• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.1
• /
• pp.71-79
• /
• 2014

In this study, an experiment with large-scale model was performed according to raising the embankment in order to investigate the behavior of failure for embankment and spillway transitional zone due to overtopping. The pore water pressure, earth pressure, settlement and failure pattern by a rapid drawdown and overtopping were compared and analyzed. The pore water pressure and earth pressure at spillway transitional zone by overtopping increased a rapidly with the expansion of seepage erosion, but the crest showed a smally change due to effect of the inclined core type. And it is considered an useful data that can accurately estimate the possibility of failure of the reservoirs. A settlement at overtopping decreased a rapidly due to failure of crest. The relative settlement difference due to change of the water level at the upstream and downstream slope cause increase largely crack of crest. The behavior of failure by overtopping was gradually enlarged towards reservoirs crest from the bottom of the spillway transition zone, the inclined core after the raising the embankment was influenced significantly to prevent the seepage erosion.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.479-483
• /
• 2004

A new calculation method of expected overtopping probability of rubble mound breakwater considering real tide occurrence has been proposed. A calculation method of expected overtopping probability of rubble mound breakwater was proposed by Kweon and Suh (2003). In their calculation, the fluctuation of tidal elevation was expressed by the sinusoidal change that yields the uniform distribution of occurrence frequency. However, the realistic distribution of tidal elevation should influence on the overtopping chance. In this study, the occurrence frequency of tidal elevation obtained from the real sea is included. The tidal elevation used in this study is collected from the east coastal part of Korean peninsular. Analyzing the annual data of the tidal fluctuation measured hourly during 355 days, the distribution of occurrence frequency is formulated utilizing by the normal distribution with one peak. Among the calculation procedures of annual maximum wave height, wave height-period joint distribution, wave run-up height and occurrence frequency of tide, only the annual maximum wave height is again chosen randomly from normal distribution to consider the uncertainty. The others are treated by utilizing the distribution function or relationship itself, It is found that the inclusion of the variability of tidal elevation has great influence on the computation of the expected overtopping probability of rubble mound breakwater. The bigger standard deviation of occurrence frequency is, the lower the overtopping probability of rubble mound breakwater is.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.35 no.4
• /
• pp.75-83
• /
• 2023

Apart from implementing hardware solutions like raising the crest freeboard of coastal structures to efficiently counter wave-overtopping, there is a simultaneous requirement for software-driven disaster mitigation strategies. These tactics involve the swift and accurate dissemination of wave-overtopping information to the inland regions of coastal zones, enabling the regulation of evacuation procedures and movement. In this study, a method was proposed to estimate wave-overtopping by utilizing the temporal variation of wave heights exceeding the structure's crown level, with the aim of developing an on-site wave measurement system for providing wave-overtopping information in the field. Laboratory model experiments were conducted on vertical seawall structures to measure wave-overtopping volumes and wave runup heights under different wave conditions and structural freeboard variations. By assuming that the velocity of water inundation on the top of the structure during wave-overtopping events is equivalent to the long-wave velocity, an overtopping discharge coefficient was introduced. This coefficient was utilized to estimate the rate of wave-overtopping based on the temporal changes in wave runup heights measured at the top of the structure. Upon reasonably calculating the overtopping discharge coefficient, it was verified that the estimation of wave-overtopping could be achieved solely based on the wave runup heights.

• Journal of Navigation and Port Research
• /
• v.30 no.8 s.114
• /
• pp.649-655
• /
• 2006

Waves progressing into the coastal area can be amplified, swashed and overtopped by a wave overtopping control structure, and it converts the kinetic energy of the waves to the potential energy with a hydraulic head above the mean sea level by conserving the overflow in a reservoir. Then the potential energy in the form of hydraulic head can be converted to electric power utilizing extremely low-head hydraulic turbine. This study aims to find the most optimal shape of wave overtopping structure which maximizes overtopping volume rate of sea water. Laboratory experiments for the performance evaluation of wave overtopping control structures were carried out in three dimensional wave tank, and the three dimensional structure models with planar wave concentration shapes(B/b) were manufactured into five classes, which were optimized by cross sectional parameters of the structure, ie, length of ramp(l), gradient of inclined ramp($cot{\phi}$) and freeboard height of the wave overtopping structure($h_e$) proposed by Shin and Hong(2005). The wave overtopping discharges were investigated with 20 incident wave conditions and wave directions of $0^{\circ},\;15^{\circ},\;30^{\circ}$.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.42-50
• /
• 2019

As the industry develops in Korea, the use of hazardous chemicals is increasing rapidly and chemical accidents are increasing accordingly. Most of the chemical accidents are caused by leaks of hazardous chemicals, but there are also accidents in which all the substances are released instantaneously due to sudden high temperature/pressure or defection of the storage tanks. This is called catastrophic failure and its frequency is very low, but consequence is very huge when it occurs. In Korea, there were 15 casualties including three deaths due to catastrophic rupture of water tank in 2013, and 64 instances of failures from 1919 to 2004 worldwide. In case of catastrophic failure, it would be able to overflow outside the bund that reduces the evaporation rate and following consequence. This incident is called overtopping. Overseas, some researchers have been studying the amount of external overflow depending on bund conditions in the event of such an accident. Based on the previous research, this study identified overtopping fraction by condition of bund in accordance with Korea Chemicals Controls Act Using CFD simulation. As a result, as the height increases and the distance to the facility decreases while meeting the minimum standard of the bund capacity, the overtopping effect has decreased. In addition, by identifying the effects of overtopping according to atmospheric conditions, types of materials and shapes of bunds, this study proposes the design of the bund considering the effect of overtopping caused by catastrophic failure with different bund conditions.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.4
• /
• pp.273-278
• /
• 2009

Overtopping Wave Energy Convertor (OWEC) is an offshore wave energy convertor for collecting the overtopping waves and converting the water pressure head into electric power through the hydro turbines installed in the vertical duct which is fixed in the sea bed. The numerical wave tank based on the commercial computational fluid dynamics code Fluent is established for the corresponding analysis. Several incident wave conditions and shape parameters of the overtopping device are calculated. The straight line type and parabolic type of the sloping arm are compared in the optimal designing investigation of the overtopping characteristics and discharge for OWEC device. The numerical results demonstrate that the parabolic sloping arm is available for wave running up and the overtopping discharge increasing.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.2
• /
• pp.154-162
• /
• 2011

A reliability analysis model is developed for evaluating the crest freeboard of vertical breakwaters based on the concepts of maximum overtopping volume of individual wave. A reliability function is formulated by defining the margin of admissible overtopping volume and maximum overtopping volume that is depend on the number of overtopping waves, dimensionless crest freeboard, and mean overtopping discharge. In addition, Level III MCS technique is straightforwardly suggested by which the related empirical parameters to reliability function can be considered to be random variables with the wide range of different uncertainties. It can be possible to calculate the probabilities of failure according to the relative crest freeboard with the variations of the incident wave directions, the structural types of vertical breakwaters, and admissible overtopping volumes in conditions of the long and short crested-waves.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.6
• /
• pp.414-421
• /
• 2011

In determination of the crest height of a vertical structure against attacking of obliquely incident waves, most of existing studies have suggested to use the overtopping reduction factor due to incident angles. However, they have not considered the amplification of wave heights and the spatial distribution of wave overtopping. In this study, a spatial distribution of overtopping due to the amplification of wave heights along a vertical structure is investigated experimentally. It is recommended that the crest height can be determined by the same manner as that for normally incident waves up to 3 significant wave lengths from the one end of the structure. However, the rest part of the structure can be done by employing the overtopping reduction factor with considering the amplification of wave heights and the spatial distribution of wave overtopping.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.6
• /
• pp.606-613
• /
• 2007

This study investigates the behavior of a plunging wave and its associated runup and overtopping through velocity measurements and suggests an empirical formula for overtopping velocities on a structure. The plunging wave breaking in front of the structure generates very bubbly flow fields. For measurements of the two phase flow field of the breaking wave, particle image velocimetry and a modified optical method were employed. The obtained velocity fields were discussed in respect of the process of wave impinging, runup and overtopping. The overtopping velocity distribution is found to have a nonlinear profile showing a maximum magnitude at its front part. The relationship of self-similarity among dimensionless parameters is observed and used to obtain the regression formula to depict the overtopping velocity.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.36 no.1
• /
• pp.11-19
• /
• 2024

In this study, the program was modified by adding the empirical formula of EurOtop (2018) to enable calculation of wave overtopping on armoured slope structures in the FUNWAVE-TVD model using the fully nonlinear Boussinesq equation. The validity of the modified numerical model was verified by comparing it with CLASH data and experiment data for the rubble mound structure. This model accurately reproduced the change in wave overtopping rate according to the difference in the roughness factor of the armoured block, and well reproduced the rate of decrease in wave overtopping rate due to the increase in relative freeboard. The overtopping rate of the armoured slope structures showed significant differences depending on the positioning condition of the armoured blocks. When Tetrapods were placed with regular positioning, the overtopping rate increased significantly compared to when they were placed with random positioning, and it was consistent with when they were placed with Rocks. Meanwhile, when rocks were placed in one row, the wave overtopping rate was greater than when rocks were placed in two rows, which is believed to be due to the influence of the roughness and permeability of the structure's surface.