• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.101-107
• /
• 1993

We carried out the useful theoretical calculation for the optimum design of a 1.48 ${\mu}m$ diode laser pumped E$r^{3+}$ doped fiber amplifier. The model we established is based on the rate equations of three level laser system and the overlap integral between fundamental mode L$P_{01}$ and E$r^{3+}$ doped area. We determined several fiber parameters (N.A., V value, fiber length, E$r^{3+}$ concentration, cutoff wavelength etc.) for the optimum design of a high optical gain. We found that our theoretical results are very useful to the design of E$r^{3+}$ doped fiber used in EDFA.

• Textile Coloration and Finishing
• /
• v.31 no.2
• /
• pp.65-76
• /
• 2019

A multi-point touch input sensor having different sizes or different capacitance touch points connected by only one pair of signal transmission lines was fabricated using a polyimide film coated with a thin copper plate. The capacitance increases with the decrease in the number of sheets of fabric spacers placed between the two sheets of the polyimide film. Therefore, the touch input sensor could be manufactured without fabric spacers, which was possible by the action of the polyimide film as a dielectric material in the capacitor. On the multi-point touch sensor, higher capacitance was obtained when pressing wider-area touch points with 10mm to 25mm diameter on average. However, the capacitance of a system comprising two sheets of touch sensors was considerably low, causing a serious overlap of the capacitance values according to the data collected from the reliability test. Although the capacitance values could be increased by stacking several sheets of touch sensors, the overlap of data was still observed. After reducing the size of all touch points to 10mm and stacking up to eight sheets of sensors, reliable and consistent capacitance data was obtained. Five different capacitance signals could be induced in the sensors by pushing touch points simultaneously.

• Journal of the Korean Society of Radiology
• /
• v.13 no.5
• /
• pp.779-783
• /
• 2019

Osteoporosis is a disease that increases the risk of fracture. In this study, dual energy X-ray absorptiometry (DXA) was used to compare bone density according to the lumbar spine rotation and inclination. The results of the showed that the bone density decreases with the rotation of the lumbar spine, but the result was not predicted in the inclination of the lumbar spine. This is due to the change of the inclusion of lumbar spine in the area of the bone and the bone density due to the overlap between the lumbar spine 1 and 4. In other words, the Radiogical technologists needs to make efforts to prevent the rotation of lumbar spine and the overlap according to the inclusion to obtain the accurate bone density results.

• The Journal of the Korea Contents Association
• /
• v.11 no.6
• /
• pp.1-7
• /
• 2011

The methodology of KOSPI forecast has been considered as one of the most difficult problem to develop accurately since short-term KOSPI is correlated with various factors including politics and economics. In this paper, we presents a methodology for forecasting short-term trends of stock price for five days using the feature selection method based on a neural network with weighted fuzzy membership functions (NEWFM). The distributed non-overlap area measurement method selects the minimized number of input features by removing the worst input features one by one. A technical indicator are selected for preprocessing KOSPI data in the first step. In the second step, thirty-nine numbers of input features are produced by wavelet transforms. Twelve numbers of input features are selected as the minimized numbers of input features from thirty-nine numbers of input features using the non-overlap area distribution measurement method. The proposed method shows that sensitivity, specificity, and accuracy rates are 72.79%, 74.76%, and 73.84%, respectively.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.25 no.2
• /
• pp.501-511
• /
• 1995

The purpose of this study was to evaluate the position and shape of mental foramen in periapical radiographs. For this study, periapical radiographs of premolar areas were obtained from the 200 adults. Accordingly, the positional and shape changes of mental foramen were evaluated. The authors obtained radiographs according to changes in radiation beam direction in periapical radiographs of premolar areas, and then evaluated the positional and shape changes of mental foramen. The following results were obtained: 1. Shapes of mental foramen were observed elliptical(34.3％), round or oval(28.0％), unidentified(25.5％) and diffuse(12.2％) type in descending order of frequency. 2. Horizontal positions of mental foramen were most frequently observed at the 2nd premolar area(55.3％), the area between the 1st premolar and 2nd premolar(39.6％), the area between the 2nd premolar and 1st molar(3.4％), the 1st premolar area(1.0％), the area between the canine and 1st premolar(0.7％) in descending order of frequency. 3. Vertical positions of mental foramen were most frequently observed at the inferior to apex(67.1％), and at apex(24.8％), overlap with apex(6.4％), superior to apex(1.7％) in descending order of frequency. 4. Shapes of mental foramen were more obviously observed at the upward 10° positioned periapical radiographs. And according to the changes of horizontal and vertical position, they were observed similar to normally positioned periapical radiographs.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1503-1510
• /
• 2011

The dropper length calculation method about the normal same encumbrance spans is well known independent to whether the pre-sag is given or not. But, the dropper length calculation method for the elevating span which consists in the end area of a tensioning section and normally consists with overlaps is not well known. In this study, firstly, we investigate the dropper length calculation method about the elevating span whether the insulator is contained in or not, we also recognize the effect of dropper length due to the change of the take-off point. Secondly, we very this calculation method with a catenary sample data and check again with Gyeongbu HSL design data.

• Proceedings of the Korean Information Science Society Conference
• /
• 1999.10a
• /
• pp.180-182
• /
• 1999

지리 정보 시스템(Geographic Information System, GIS)에서 가장 주요한 부분을 차지하는 것 중의 하나가 공간 데이터 모델(spatial data model)에서 정의된 각 공간 데이터들간의 공간 관계 연산자(spatial relational operator)의 효과적인 구현이다. 공간 데이터는 점(point), 선(line), 면(area)으로 표현될 수 있다. 이들 사이의 모든 공간 관계는 Disjoint, Touch, Cross, In, Overlap의 다섯 가지 연산자로 표현 가능함이 알려져 가능함이 알려져 있으며, 이들에 대한 실체적인 위상 관계를 표현하는 다양한 수학적 모델링 방법이 존재한다. 하지만, 실제 이들 공간 연산자들을 수학적 모델에 따라 그대로 구현하려고 하면, 컴퓨터 상에서는 표현할 수 없다거나 많은 자원을 차지하는 데이터 구조를 필요로 한다거나, 또는 비효율적인 알고리즘으로 구현할 수 밖에 없는 현실적인 어려움에 봉착한다. 그 중에서도 구현하기 어려운 연산은 면과 선과의 관계, 면과 면과의 공간 관계를 찾아내는 공간 연산자이다. 본 논문에서는 선분의 양끝점을 이용하여 면과 선분(line segment)과의 관계를 찾아내는 알고리즘을 제안한다. 이 알고리즘을 사용하여 면과 선, 면과 면과의 관계를 찾아내는 공간 연산자를 효율적으로 구현할 수 있다.

• Journal of Environmental Science International
• /
• v.22 no.9
• /
• pp.1227-1234
• /
• 2013

Between July and October 2011, radio-tracking was used to analyze the characteristics of home ranges and day roosts of Myotis aurascens by using 3 individuals (male: 2, female: 1). Bat capturing was conducted at a bridge and a nearby forest in Ulju-gun, Ulsan-si. We attached radio transmitters (0.32 g) to the bats and monitored them by using a radio receiver with a Yagi antenna. Home-range analysis of M. aurascens by using 100% minimum convex polygon (MCP) and 95% MCP showed an average of 106.5 ha and 89.3 ha, respectively, and 50% kernel home range (KHR) showed an average of 8.4 ha. Home range overlap of the 3 bats was observed at the bridge and at nearby water bodies as the core areas, and the size of the home range overlap was 7.3 ha by 100% MCP, 5.9 ha by 95% MCP, and 1.6 ha by 50% KHR. The home range for each bat consisted of the main foraging sites, and the types of foraging sites were similar. M. aurascens-01(M-01) used the bridge and nearby water bodies as the nightly main core areas, M. aurascens-02(M-02) used rice fields and water bodies adjacent to the forest as core areas, and M. aurascens-03(M-03) used water bodies and resident areas as core areas. Although rice fields and resident sites represented the core areas of the home ranges of M-02 and M-03, habitat use was the highest near water bodies as the core area for all the 3 bats. The types of day roosts in this study were a wooden house, canopies of a broad-leaved woodland, and banks of rice fields. The roosts in the wooden house and canopies of the broad-leaved woodland were located within the forest, and the roost in the banks of rice fields was also adjacent to the forest. Our results revealed that the main home range and foraging sites of M. aurascens were located near water bodies as the core area, and forests and places adjacent to the forests were used as day roosts.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.41 no.4
• /
• pp.282-288
• /
• 2008

Feeding ecology of the white-spotted conger eel Conger myriaster in the Southern Sea of Korea was examined. Specimens were caught monthly from January 2004 to December 2006. Primary prey items of C. myriaster included fish, shrimp, and crabs. C. myriaster exhibited a nocturnal feeding strategy and preyed upon a wide range of pelagic fish groups(e.g., Engraulis japonicus, Glossanodon semifasciatus, and Maurolicus muelleri). This species was also an opportunistic feeder that exploited the available prey in each area(i.e., fish in the A area and shrimp in the B area). The composition of the diet of C. myriaster exhibited seasonal fluctuations that were related to food availability during each season. The observed ontogenetic shifts in diet were relatively clear, despite substantial overlap between the 10 cm and 20 cm groups of C. myriaster.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.3
• /
• pp.273-278
• /
• 2017

This paper is to study a technique to detect the real-time route aberrance on the passage route using bumper area of the ship domain theory. In order to evaluate the risk of route aberrance, a quarter line was created between the center line and the outer line, and a passage route with the image line outside the outer line was designed. It calculated the real-time route aberrance with the vessel bumper area to measure the risk level on the passage route. The route aberrance using overlap bumper area was simulated through three kinds of scenario vessel at the designed passage route. In this paper, we proposed Ratio to Aberrance Risk as one of the evaluation parameter to detect the route aberrance risk at each sector in the passage route and to give the evaluation criteria of 5 levels for seafarer's navigation safety. The purpose of this work is to provide the information of the route aberrance to seafarer automatically, to make it possible to prevent the human errors of seafarer on the high risk aberrance route. As the real-time risk of route aberrance on the passage route is automatically evaluated, it was well thought that seafarer can have only a little workload in order to know the risk of route aberrance at early-time. Following the further development of this work, the techniques for detecting the real-time route aberrance will be able to use the unmanned vessel.