• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.33-42
• /
• 2003

Since the cut slope has been big concern due to frequent failures, the government decided to include cut slopes in the“Act for Safety Control of Public Structures”. Based on the Act, the cut slope whose height is over 50m and length is over 200m should be inspected on the regular basis. According to the Act, KISTEC developed the objective evaluation method for the condition of cut slope. The evaluation method is divided into two categories: evaluation for damaged condition and evaluation for failure affecting factor. Based on the evaluation results, the cut slope is graded from A to E. In this study, the process to evaluate the cut slope condition and the evaluation criteria to divide the grade of cut slope are introduced.

• Explosives and Blasting
• /
• v.20 no.2
• /
• pp.7-19
• /
• 2002

The cut is placed high up in the section, the 1st sloping holes below the cut, and divided all the holes located below the 1st sloping holes into a certain area with longitudinal section, to lower pollution made from tunnel blasting. With the sequential blasting machine, after I first blasted holes around the cut holes by a pre-splitting method, blasted the cut area and the 1st sloping holes. The 1st and 2nd sloping holes divided areas are initiated gradually to free face upwards made by the cut. Especially, I pre-splinted contour holes previous blast the before sloping holes from the contours. The ground vibration from the earth surface just over the advance face decreased about 42.0% compare with the down blasting method under the condition of equal charge weight per delay. I controlled the crack and over break of the mother rock by pre-splitting contour holes before blast the first sloping holes from the contours. The peak values of noise and air blast by blasting decreased about 10dB more than the down blasting method. the noise and air blast diminished gradually as a round. The throw distance of the fly rock was decreased about 55%.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.3
• /
• pp.8-15
• /
• 2004

A significant error in the end milling processes is generated due to using slender tools of which the strengths are not sufficient. In order to obtain the desired machining accuracy, therefore, it is general that at first the rough cut is implemented, then the finish cut is followed. The rough cut eliminates large volume and the finish cut does the remained part. This remaining portion after the rough cut is called as the finish allowance. Larger finish allowances make it hard to get precise dimensions at a following finish cut. Smaller finish allowances are helpful for good dimension, but it sometimes is responsible for inferior surface qualities and over cuts. This study suggests a guidance for the optimum finish allowance for machining accuracy improvement, in which the rough cuts are regulated to remain the desired margins without any over cuts. Some experiments were carried out with various cutting conditions including the change of tool strengths and depth of cuts, and also extended to up millings as well as down millings.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.524-529
• /
• 2002

In this paper, we report the development of two DEM (digital elevation model) generation algorithms over urban areas from an IKONOS stereo pair. One ("EpiMatch") is originally developed for SPOT images and modified for IKONOS images. It uses epipolar geometry for accurate DEM generation. The other is based on graph-cut algorithm in 3D voxel space. This algorithm is believed to work better on height discontinuities than EpiMatch. An IKONOS image pair over Taejon city area was used for tests. Using ground control points obtained from differential GPS, camera model was set up and stereo matching applied. As a result, two DEMs over urban areas were produced. Within a DEM from EpiMatch small houses appear as small "cloudy" patches and large apartment and industrial buildings are visually identifiable. Within the DEM from graph-cut we could achieve better height information on building boundaries. The results show that both algorithms can generate DEMs from IKONOS images although more research is required on handling height discontinuities (for "EpiMatch") and on faster computation (for "Graph-cut").

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.12
• /
• pp.86-92
• /
• 2002

This paper presents a new model of NC verification in NC milling using z-map. The model can describe the motion of machine tool like a real machine effectively. The model uses x, y, and z directional feed rate as well as cutting data for modeling Z-map of workpiece. The model verifies the over-cut, the under-cut and the surface topography using NC codes and cutting conditions. To investigate the performance of the model, simulation study was carried out. As the results, the model gave the geometry accuracy of workpiece, the surface topography, and the chip loads.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.4
• /
• pp.365-369
• /
• 2001

This paper presented a new model of virtualized CNC milling machine. The model verifies the over cut, the under cut and the surface roughness using NC file generated from CAM and cutting condition. The model uses Z-map model to verify workpiece. In this paper, the model used the velocities of x, y and z direction and obtained a center point of a hall end mill for modeling Z-map of workpiece. To investigate the performance of the model, simulation study was carried out. As the results, the model gave geometry accuracy of workpiece, the surface roughness and the chip loads in finish cutting that can predict tool chipping. The virtualized CNC machine can he used a flat end mill, a ball end mill and a rounded end mill.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.725-729
• /
• 2000

This paper presented a new model of NC verification in ball end milling. The model verifies the over cut the under cut and the surface roughness using NC file generated from CAM and cutting condition. The model uses Z-map model to verify workpiece. In this paper, the model used the velocities of x, y and z direction and obtained a center point of a ball end mill for modeling Z-map of workpiece. To investigate the performance of the model simulation study was carried out. As the results, the model gave geometry accuracy of workpiece, the surface roughness and the chip loads in finish cutting that can predict tool chipping.

• The korean journal of orthodontics
• /
• v.21 no.3
• /
• pp.657-670
• /
• 1991

It was said that early rapid palatal expansion was the treatment of choice in case of maxillary constriction with posterior crossbite. The author tried to assess dimensional changes of nasal and oral cavity before rapid palatal expansion and over 4 months of retention by use of three coronal tomograms through the incisal, molar, and maxillary tuberosity areas. The subjects of this study were consisted of 9 boys and 11 girls ranging from 11 to 13 years old. The results were as follows: 1. A mean change in maxillary first molar width was 3.68mm and a mean change in nasal cavity width was 2.26mm after 6.70mm expansion by Hyrax-type screw and over 4 months of retention tomographically in molar cut. 2. A change in nasal cavity width tomographically showed in order of molar cut, incisal cut, maxillary tuberosity cut respectively. 3. There was no correlation between changes in oral cavity width and nasal cavity width.

• The Research Journal of the Costume Culture
• /
• v.11 no.6
• /
• pp.967-971
• /
• 2003

As the concerns over health increased in 1990's, research and development on the health material were also activated. The development of UV-cut textile became the hot issue, because the damage of W irradiation due to ozone depletion has become widely known. UV-cut effect is determined by the material, the color, the organization and the density of UV-cut fibers. UV-cut effect is very different according to the fibers. Polyester is known to have a better effect. Even in the same textile material, staple fiber has more effect than filament fiber. Different colors have different offsets. Although textiles have the same color, the effects can be different according to the depth of color. PET, PET/cotton blend, nylon and cotton fabrics were ultraviolet cutting finished with padding method using several absorbers. These UV-cut effect can be improved through the processing. Safety of UV-cut textile for the body must be considered future, Until now the figure of the UV-cut effects has been emphasized. There has been no experiment on the human body, although the textiles are directly on the human body. Futhermore there os no safety standard of UV-cut textiles. Therefore every effort will be made to set the standard UV-cut processing is established. The need of UV-cut products will be known to the consumers.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.1
• /
• pp.65-73
• /
• 2004

In this paper, we propose a tunnel establishment scheme using Next Hop Resolution Protocol over mobile IP networks, which consist of LAN-based IP networks and ATM-based IP networks. As a basic idea, we use the shortest path algorithm to establish a short-cut tunnel between HA and FA. Also, we classify methods for establishing a short-cut tunnel into four cases considering the locations of HA, FA, CN and MN. To confirm the advantages of our schemes, which deliver packets using short-cut tunnel in optimized path method over mobile IP networks, we performed mathematical analysis and simulation, compared proposed schemes with existing IP routing method in terms of transmission delay between CN and MN. The simulation results show that our scheme have superior performance to that of existing IP routing mechanism, because the store-and-forward delay which occurred in IP routing mechanism is considerably reduced in short-cut tunnel over ATM networks.