• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.101-103
• /
• 2007

Since they use the low switching frequency in multilevel inverter systems, they generate the high low frequency harmonic components. Generally, LC filter is used at the output terminal of inverter systems to solve this problem. But it causes a voltage drop at the output terminal by use of damping resistors, and causes the problem in which system efficiency decreases due to power loss of the damping resistor. In this paper, we proposed an output filter design method for NPC three-level inverter systems with low switching frequency. And we analyzed the efficiency of the proposed filter system, and the effectiveness of the proposed system is verified by simulation and experimental results.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.347-349
• /
• 2013

This paper describes analysis and calculation of line frequency ripple current according to output capacitor value and effects of LED connection in the single stage flyback converter with high power factor. The low frequency output ripple current delivered from single stage converter has been analyzed in detail and the method evaluating parasitic resistance included in LED has been provided. In order to verify the equation derived in this paper, the single stage flyback converter has been designed with constant output current regulation with DCM operation. Experiments were conducted with different LED load structures to analyze the effect of LED parasitic resistance on output ripple current. As test results, the calculation can provide guide line to select capacitor values depending on output ripple current and LED characteristics.

• Journal of Advanced Navigation Technology
• /
• v.6 no.1
• /
• pp.52-62
• /
• 2002

Electrical characteristics of two types of 20 GHz Push-Push GaAs MESFET dielectric resonator oscillators having Wilkinson and T-junction power combiners for the output stage have been investigated. The Push-Push oscillator for suppressing fundamental frequency 10 GHz and enhancing 20 GHz has been designed and realized in microstrip configuration on 20 mil thick RT-Duroid(${\varepsilon}_r$=2.52) teflon substrate. Two different types of power combiners, T-junction and Wilkinson, have been considered. Whenever one type of the combiners has been adopted for the output circuit, output power, phase noise and fundamental frequency suppression characteristics of the oscillator have been measured. When the Wilkinson power combiner was used, a maximum output power of 5.67 dBm, a phase noise of -105.5 dBc/Hz at an offset frequency of 100 kHz and a fundamental frequency suppression of -29.33 dBc have been measured. When the T-junction power combiner was used, a maximum output power of -1.17 dBm, a phase noise of -102.2 dBc/Hz at an offset frequency of 100 kHz and a fundamental frequency suppression of -17.84 dBc have been measured.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.1
• /
• pp.54-62
• /
• 1988

For code division multiple access, a frequency synthesizer of elementary components is necessary in the system application of frequency hopped spread spectrum communication. This paper proposes the model of N-loop PLL frequency synthesizer to be adaptied for generating the output frequency resultes in the frequency hopping pattern and to be easy in practical application of the system. It was analyzed how the frequency divider ratio distribute, what the method to decide frequency divider ratio is and what relationship of bandwidth of BPF and degree of multiple have is also analyzed in order to hop the desired frequency output.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.361-365
• /
• 2002

Advancements in silicon phase control (SCR) technologies provide an arc welding power supply that has the capability to allow the alteration of the Alternating Current (AC) welding output. These technologies provide a square wave output involving sixteen frequency selections and multiple balance selections. While an AC out put is known to minimize magnetic disturbances associate with Direct Current (DC), the potentials of a non-sinusoidal waveform have not been explored. The focus of the paper is to determine the effects that the frequency and balance of an AC wave form output will have upon a high speed Submerge Arc (SAW) application. The test matrix of the project includes welding .250" steel plate. Joint type is square groove with a travel speed of 65 IPM. Each of the weld parameters was held constant, only the frequency and/or balance were altered between welds. Each frequency/balance combination involved three-gap spacing. Upon completion of the welds the bead profiles were measured and recorded. A relationships/trends were observed with various frequency and balance values. Optimum frequency and balance values were found for the .250" square groove application which permit consistent weld sizing, ease of slag removal, and minimal plate distortion.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2243-2257
• /
• 2016

This paper presents a two stage three-phase proton exchange membrane fuel cell (PEMFC) generation system. When the system is connected to a three-phase load, it is very sensitive to the characteristics and type of the load. Especially unbalanced three-phase loads, which result in a pulsating power that is twice the output frequency at the inverter output, and cause the dc-link to generate low frequency ripples. This penetrates to the fuel cell side through the front-end dc-dc converter, which makes the fuel cell work in an unsafe condition and degrades its lifespan. In this paper, the generation and propagation mechanism of low frequency ripple is analyzed and its impact on fuel cells is presented based on the PEMFC output characteristics model. Then a novel method to evaluate low frequency current ripple control capability is investigated. Moreover, a control scheme with bandpass filter inserted into the current feed-forward path, and ripple duty ratio compensation based on current mode control with notch filter is also proposed to achieve low frequency ripple suppression and dynamic characteristics improvement during load transients. Finally, different control methods are verified and compared by simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1896-1897
• /
• 2007

Medical equipment of high frequency has been presently applied to various parts of human body and novel treatment effects have been shown by it. Recently there are many cases that high frequency apparatus has been used in dermatology as the interest in beauty has been growing. Especially used in skin, blood volume is increased by keeping surface temperature of skin at around $43^{\circ}C$ and domodex folliculorum are treated by applying high electric field. It is the aspect we consider that increasing blood volume and domodex folliculorum treatment take effect on hair loss. In this study, high frequency electrotherapy apparatus was proposed to be applied to hair loss treatment. For that, human body was experimented with varying output voltage and frequency. The adjustable switching signal for treatment was obtained from 100[kHz] to 1000[kHz] by using DSP. Stable output specific was also obtained by feedback control to protect human body. The best hair growth conditions were the output voltage of 1.2[kV], the frequency of near 300[kHz] and the maximum current of 2[mA]. We apply this high frequency electrotherapy apparatus to two bald men, 46-year-old and 45-year-old. After treatment for a month they had thick and strong hair.

• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.36-39
• /
• 2000

The adaptive learning circuit is designed the basis of modeling of MFSFET (Metal-Ferroelectric-Semiconductor FET) and the numerical results is analyzed. The output frequency of the adaptive learning circuit is inversely proportioned to the source-drain resistance of MFSFET and the capacitance of the circuit. The output frequency modulation of the adaptive learning circuit is investigated by analyzing the source-drain resistance of MFSFET as functions of imput pulse numbers in the adaptive learning circuit and the dimensionality factor of the ferroelectric thin film. From the results, the frequency modulation characteristics of the adaptive learning circuit, that is, adaptive learning characteristics which means a gradual frequency change of output pulse with the progress of input pulse are confirmed.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.342-345
• /
• 2014

An active frequency doubler monolithic microwave integrated circuit (MMIC) for E-band transceiver applications is presented in this letter. This MMIC has been fabricated in a commercial $0.1-{\mu}m$ GaAs pseudomorphic high electron mobility transistor (pHEMT) process on a 2-mil thick substrate wafer. The fabricated MMIC chip has been measured to have a high output power performance of over 13 dBm with a high fundamental leakage suppression of more than 38 dBc in the frequency range of 71 to 86 GHz under an input signal condition of 10 dBm. A microstrip coupled line is used at the output circuit of the doubler section to implement impedance matching and simultaneously enhance the fundamental leakage suppression. The fabricated chip is has a size of $2.5mm{\times}1.2mm$.

• Journal of the Korean Magnetics Society
• /
• v.22 no.6
• /
• pp.200-203
• /
• 2012

In this study, we have investigated that the operation frequency dependences of the output properties of the orthogonal fluxgate sensor which was fabricated with a ferrite core. An orthogonal fluxgate sensor should be operated in as high as possible frequency to enhance its sensitivity in the case of small sized sensor, because sensitivity of the sensor is proportional to cross section area, winding number and operation frequency. In this study, we investigated the correspondence of the frequency dependence of output and the reactance (inductance and capacitance) of pickup coil and cable. Experimental results represented that we could obtain maximum output (= sensitivity) at optimal frequency which is near LC resonance frequency of the pickup coil and cable.