• Proceedings of the KIPE Conference
• /
• 1996.06a
• /
• pp.26-30
• /
• 1996

This paper proposes a novel method to reduce the torque ripple due to the non-ideality of the current sensing parts in vector-controlled inverter-fed PMSM(Permanent Magnet Synchronous Motor) drive systems. The motor output torque equations are derived in terms of their offset voltages and different voltage transducing gains. And the effects of phase current errors on motor torque are analyzed for both salient PMSM and non-salient PMSM. The proposed method can eliminate the torque ripple by nulling the offset voltages and setting the voltage transducing gains to the same value. To verify the proposed method, digital simulations are carried out for non-salient PMSM.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.575-578
• /
• 2003

This paper presents a new current control method to reduce torque ripple of Brushless DC Motor during commutation. In the proposed control strategy, the current slopes of rising and decaying phase during commutation is equalized by the compensation voltage. By adding the compensation voltage for it to the current controller output, the reduced torque ripple can be obtained. The simulation and experimental results show that the proposed method reduces the torque and the current ripples significantly.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.409-410
• /
• 2012

Speed output has ripple such as periodic torque ripple if load torque with periodic ripple was injected in AC motor. In this paper, it is proposed method to reduce speed ripple through novel speed control method. It replaces algorithm to compensate torque ripple. Proposed method demonstrated through simulation using MATLAB SIMULINK.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.4
• /
• pp.121-129
• /
• 1997

Gear train system test rig of power circulating type was fabricated, and systematic experiment for measuring dynamic characteristics of the planetary gear trains in the low speed region has been carried out using the test rig. The measured parameters are fillet strains of the sun gear and ring gear, carrier displacements, torques of the input and output shafts. The results are as follows : i) Even though the loading torque is constant, torque variation has been observed on the input and output hafts, ii) The variation of the torque has two frequency components, i.e. lower one of the input shaft rotation and higher one of the two teeth meshing, iii) The variation of the fillet strains shows the same tendency as that of the torque, iv) The loci of the carrier depend on the torque and rotational speed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.12
• /
• pp.2189-2196
• /
• 2016

This paper proposes a new finite control set-model predictive control (FCS-MPC) method for induction motors. In the method, the reference state that satisfies the given torque and rotor flux requirements is derived. Cost indices for the FCS-MPC are defined using the state tracking error, and a linear matrix inequality is formulated to obtain a proper weighting matrix for the state tracking error. The on-line procedure of the proposed FCS-MPC comprises of two steps: select the output voltage vector of the two level inverter minimizing the cost index and compute the optimal modulation factor of the minimizing output voltage vector in order to reduce the state tracking error and torque ripple. The steady state tracking error is removed by using an integrator to adjust the reference state. The simulation and experimental results demonstrated that the proposed FCS-MPC shows good torque, rotor flux control performances at different rotating speeds.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.106-114
• /
• 1998

Cogging torque is often a principal source of vibration and control difficulty in permanent magnet motors, especially at low speeds and loads. For example, reduction of cogging torque is an important specification for DC motors used for electric power stee- ring. This paper examines two motor design techniques, stator tooth notching and rotor pole skewing with magnet pole shaping, for reduction of cogging torque, and the effect of each method on the airgap flux, and the use of the Maxwell stress method and Fourier decomposition to calculate the periodic cogging torque. The analyses show that the cogging torque can be nearly eliminated by the suggested designs, with minimal scacrifice of output torque.

• Proceedings of the KIPE Conference
• /
• 2013.07a
• /
• pp.212-213
• /
• 2013

This paper proposes the algorithm of torque distribution in the electric wheel-chair using 2D joystick for drive safety. For the accurate driving performance, the specific and precise torque distribution is required in both wheels depending on signals of X-Y axis that is generated from 2D joystick. The signals of X-Y axis from joystick are transformed into the propulsion force and the torque reference. And the torque reference can be generated through the dynamic model of wheel-chair. The optimal dynamic characteristics of the electric powered wheelchair can be obtained, by adjusting the sensitivity coefficients of propulsion force and torque reference, In addition, the system takes smooth and stable control characteristics due to continuous torque output at all directions of joystick. The several simulations verify the usefulness of the proposed algorithm about torque distribution.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.361-364
• /
• 2013

Permanent magnet flux switching motor (PMFSM) is a novel double salient machine which employs PMs instead of field winding for excitation. PMFSM contains only one set of armature winding, thereby features simple control strategy, low cost power inverter and substantial high efficiency. Due to the unique double salient structure and operation principle, the generated cogging torque in PMFSM is critical and quite different compared to the traditional PM machines. This paper presents and investigates various design techniques for reducing cogging torque in PMFSM. Firstly, an analytical model is proposed to study the influence of different methods on cogging torque. Then the optimal design parameters for minimizing cogging torque are determined by the analytical model, which significantly reduces the computational efforts. At last, the cogging torque with different design approaches are simulated by FEA along with the average output electromagnetic torque, which validates the analysis above.

• Journal of Sensor Science and Technology
• /
• v.27 no.2
• /
• pp.105-111
• /
• 2018

In this paper, a torque sensor is designed and fabricated to measure the knee joint torque of a walking assist robot for stroke patients. The torque sensor sensing part was modeled on the link of the part connected to the knee joint motor. The torque capacity of the knee joint was calculated by simulation and the size of the torque sensor sensing part was designed using the finite element method. The torque sensor was fabricated by attaching a strain gauge to the sensing part. Characteristic experiments were conducted to characterize the torque sensor, and the torque sensor was calibrated to utilize it for the control of the walking assist robot. As a result of the characteristics test, the reproducibility error and the nonlinearity error of the torque sensor were 0.03% and 0.04%, respectively. Therefore, it is considered that the developed torque sensor can be used to measure the torque applied to the knee joint when walking on a walking assist robot.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.690-695
• /
• 2004

The present study is an investigation on the characteristics of heavy load toque converter by experimental process. To get the dynamic performance, the dynamometer was used with a parameters of speed, torque, oil pressure and oil flux, etc. The torque converter was tested for various input speed, output oil pressure and input oil flow rate. All experiments were investigated in case that the speed ratio is increased. The torque ratio and capacity factor was in inverse proportion to speed. Engine revolution had a more effects at region of low speed ratio. But, the opposite phenomena were represented increase of efficiency. In result of this experiments, the characteristics of torque converter were not influenced by oil pressure and oil flux.