• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.112-121
• /
• 2015

In this paper, powertrain of output split type plug-in hybrid electric vehicle is analyzed for the operation range of speed, torque, and power. First, it is assumed that the efficiency of motor is 100%. And, the speed and torque equations are derived based on the lever analogy. With the above equations, the simulations are performed for the powertrain of output split type plug-in hybrid electric vehicle. From the simulation results, it is found that the output torques of EV1 and series modes are larger than the EV2 and power split modes' ones. It means the EV1 and series modes can be used for the rapid acceleration. But the EV1 and series modes can be used only the velocity of under the 120 km/h. It is because the motor reaches its maximum speed when the velocity is over the 120 km/h for the EV1 and series modes. When the engine is turned on, the engine power is transmitted through the two motors. But, the power split mode shows the power split of engine at the output shaft, and it has the point of zero motor power. Thus, the transmission efficiency of the power split mode can be higher than the series mode's one, it the motor efficiency is considered.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.6
• /
• pp.60-65
• /
• 2002

The purpose of this study is to measure and compare the output power characteristics and optical gain for selenium vapour laser depending on the He gas purity. The purity of the He gas was improved with a special He-filter. During the measurement the individual wavelengths were selected with a birefringent filter. The result shows that compared with those of laser without He-filter, the output-coupling power and small signal gain of laser with He-filter increase in the most of the lines. Especially, the output-coupling power and small signal gain for the strong lines (497.6 nm, 499.3 nm, 506.9 nm, 517.6 nm, 522.8 nm, 530.5 nm), blue(460.4 nm, 464.8 nm) and red(644.4 nm 649.1 nm) lines lies notably higher.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.7 no.3
• /
• pp.11-22
• /
• 1997

The number of output sequence was proposed as a characteristic of binary sequence generators for cryptographic application, but in general most of binary sequence generators have single number of output sequence. In this paper, we propose two types of binary sequence generators with a large number of output sequences. The first one is a Switched-Tap LFSR (STLFSR) and it applies to the generalized nonlinear function and the Geffe's generator as example. The other is a generalized memory sequence generator(GMEM-BSG) which is an improved version of the Golic's memory sequence generator (MEM-BSG) with a large number of output sequences, and its period, linear complexity, and the number of output sequence are derived.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.3
• /
• pp.284-291
• /
• 2006

Recently with the motorizing of electric home appliances and car systems, there is increasing interest in high efficiency electric motors. Thus, the present study described the operating characteristics of coreless AFPM motor that is highly efficient in high speed driving, and discussed its electric characteristics from the perspective of design. In particular, we examined back electromotive force and the magnetic field characteristic in slits, which have significant effects on the characteristic of the motor, and conducted simulation and experiment on control characteristic according to inductance characteristic. This study analyzed torque speed and efficient operation characteristic as well as control characteristic through comparing the result of motor design with the result of output characteristic experiment based on the electric network method. Furthermore, we evaluated vibration and noise that may occur due to the absence of core.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.716_717
• /
• 2009

This paper deals with the characteristic analysis & optimum design of Permanent Magnet Assisted Synchronous Reluctance Motor(PMASynRM) for Premium Efficiency Performance. The focus of this paper is characteristic analysis of d and q-axis inductances and torque according to magnetizing quantity of interior permanent magnet for PMASynRM. The d and q-axis current component ratios, load angles of a PMASynRM are investigated quantitatively on the basis of the proposed analysis method and the experimental test. Comparisons are given with output characteristic curves of normal SynRM and those according to the load in PMASynRM, respectively. And optimum design of PMASynRM is performed by Response Surface Methodology(RSM).

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.4
• /
• pp.175-182
• /
• 1994

In this study, we present unvoiced consonant recognition system using characteristic parameters of the phoneme of the each syllable. For the recognition, the characteristic parameters on the time domain such as ZCR, total energy of the consonant region and half region energy of the consonant region, and those on the frequency domain such as the frequency spectrum of the transition region are used. The objective unvoiced consonants in this study are /ㄱ/,/ㄷ/,/ㅂ/,/ㅈ/,/ㅋ/,/ㅌ/,/ㅍ/ and /ㅊ/. Each characteristic parameter of two regions extracted from these segmented unvoiced consonants are used for each recognition system of the region, independently, And complementing two outputs of each other system, the final output is to be produced. The recognition system is implemented using MLP which has learning ability. The recognition simulation results for 112 unvoiced consonant samples are that average recognition rates are 96.4$\%$ under 80$\%$ learning rates and 93.7$\%$ under 60$\%$ learning rates.

• 한국정보통신설비학회:학술대회논문집
• /
• 2006.08a
• /
• pp.35-38
• /
• 2006

Using the repeaters is indispensable to WiBro services. Repeater types are distinguished by usage, output power and required performance. In the paper, we have studied on the WiBro digital optic repeater design which has excellent performance characteristic than any other repeaters. WiBro has specific characteristic on modulation method TDD(Time Division Duplex)/OFDMA(Orthogonal Frequency Division Multiple Access) so that it demands specified H/W to design WiBro repeater. Switching technique has been introduced because of TDD characteristic in each amplifier on the repeater. Time Advance technique has been considered because of OFDM characteristic among RAS(Radio Access Station) and repeater. In this paper, we have studied on these techniques to increase repeater cell coverage and distance between RAS and repeater.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.119-122
• /
• 2002

This paper presents detailed characteristic of a Reluctance Synchronous Motor(RSM) which has a transverse-laminated rotor. First of all, the analysis of a magnetic circuit field between stator and rotor should be achieved in order to predict the performance characteristic of the RSM. For the analysis of a magnetic circuit field, the Finite Element(FE) analysis and a experimental method are used. The analytical result of the inductance flux distribution, vector potential, and the output shows some good characteristic along with the load condition.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1097-1102
• /
• 2007

This paper describes the development of 6-axis force/moment sensor for an intelligent robot's foot. In order to walk on uneven terrain safely, the foot should perceive the applied forces Fx, Fy, Fz and moments Mx, My, Mz to itself. The applied forces and moments should be measured from a 6-axis force/moment sensor attached to a humanoid robot's foot(ankle). They in the published paper already have some disadvantage in the size of the sensor, the rated output and so on. The rated output of each component sensor (6-axis force/moment sensor) is very important to design the 6-axis force/moment sensor for precision measurement. Therefore, each sensor should be designed to be gotten similar the rated output under each rated load. So, the sensing elements of the 6-axis force/moment sensor should get lots of design variables. Also, the size of 6- axis force/moment sensor is very important for mounting to robot's foot. In this paper, a 6-axis force/moment sensor for perceiving forces and moments in a humanoid robot's foot was developed using many PPBs (parallel plate-beams). The structure of the sensor was newly modeled, and the sensing elements (plate-beams) of the sensor were designed using FEM (Finite Element Method) analysis. Then, the 6-axis force/moment sensor was fabricated by attaching strain-gages on the sensing elements, and the characteristic test of the developed sensor was carried out. The rated outputs from FEM analysis agree well with that from the characteristic test.

• Journal of Korea Technology Innovation Society
• /
• v.9 no.2
• /
• pp.350-372
• /
• 2006

The main purpose of this study is to investigate the technology related facts which determine the difference of the output of companies in the fields of IT and BT industries in Korean. The determining facts consist of the technology development strategy, the characteristic of R&D groups, and the ability of managing knowledge assets. Three kinds of regression model are made by using 3 determining facts from total model to IT and BT model to investigate the research purpose of this study. The technology development strategy consists of 2 sub facts, as technology innovation and product upgrade. The characteristic of R&D group consists of 2 sub facts, as the characteristic of task and the intensity of R&D group members. The ability of managing knowledge assets consist of 3 sub elements, as the ability of creating knowledge assets, the ability of holding in common knowledge assets, and the ability of developing the value of knowledge assets.