• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.16-20
• /
• 2002

This paper describes the resistive FET mixer with low IF for the 4-Ch DBF(Digital Beam Forming) receiver with LNA(Low Noise Amplifier). This DBF receiver based on the direct conversion method is generally suitable for high-speed wireless mobile communications. A radio frequency(RF), a local oscillator(LO) and an intermediate frequency(IF) considered in this research are 2.09 ㎓, 2.08 ㎓ and 10㎒, respectively. The RF input power, LO input power and Vgs are used -10㏈m, 6㏈m and -0.4 V, respectively. In the 4-Ch resistive FET mixer with LNA, the measured IF and harmonic components of 10㎒, 20㎒, 2.09㎓ and 4.17㎓ are about -12.5 ㏈m, -57㏈m, -40㏈m and -54㏈m, respectively. The IF output power observed at each channel of 10㎒ is about -12.5㏈m and it is higher 27.5 ㏈m than the maximum harmonic component of 2.09㎓. Each IF output spectrum of the 4-Ch is observed almost same value and it shows a good agreement with the prediction.

• Korean Journal of Optics and Photonics
• /
• v.6 no.1
• /
• pp.16-20
• /
• 1995

We have studied the spectral narrowing characteristics of the tunable Ti:sapphire laser pumped by the second harmonic generation of Nd:YAG laser. Ti:sapphire laser has uniform excitation distribution by both-side end pumping. We have controlled the angle of grating linearly and achieved the continuous selection of wavelength in the broad range from 705 to 835 nm. The output energy of $380{\mu}J$ at 790 nm. the spectral linewidth of $0.13cm_{-1}$ and the beam divergence of 1.2 mrad have been obtained. The wavelength range with power more than 50% of maximum output was 730-825 nm.825 nm.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.3
• /
• pp.41-51
• /
• 1997

In this study, two types of the direct digital frequency synthesizers (DDFS) designed and implemented using 1.0.mu.m CMOS gatearray(SOG) technolgoies are interoduced. To analize the effect of the number of phase bits(L), address data bits(A), and DAC bits (D) on the output spectrums of the DDFSs, the NCO-based BCD-DDFS composed of L=24, A=14, and D=8, and the improved binary-DDFS composed of L=24, A=8, and D=10 have been studied. The chips have been designed with and without a noise shapper to reduce spurious noises due to phase truncation and reduced sine ROM in output spectrum.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.873-879
• /
• 2016

A charge pump circuit with very short turn-on time is presented for minimizing reference spurs in CMOS PLL frequency synthesizers. In the source switching charge pump circuit, applying proper voltages to the source nodes of the current source FETs can significantly reduce the unwanted glitch at the output current while not degrading the rising time, thus resulting in low spur at the synthesizer output spectrum. A 1.1-1.6 GHz PLL synthesizer employing the proposed charge pump circuit is fabricated in 65 nm CMOS. The current consumption of the charge pump is $490{\mu}A$ from 1 V supply. Compared to the conventional charge pump, it is shown that the reference spur is improved by dB through minimizing the turn-on time. Theoretical analysis is described to show that the measured results agree well with the theory.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.12
• /
• pp.1700-1705
• /
• 2013

A second harmonic millimeter wave oscillator utilizing sub-harmonic injection-synchronization is presented. A 8.7GHz oscillator with MES-FET is designed, and is driven as a harmonic output oscillator at 17.4GHz by means of sub-harmonic injection-synchronization. The oscillator operates as a multiplier as well as a oscillator in this scheme. Adopting this method, a high sable, high frequency millimeter wave source is obtainable even though self-oscillating frequency of an oscillator is relatively low. The range of injection-synchronization is about 26MHz, and is proportional to the input sub-harmonic power. The spectrum analysis of the 2nd harmonic output frequency shows remarkably decreased the phase noise level.

• Smart Structures and Systems
• /
• v.19 no.5
• /
• pp.567-576
• /
• 2017

Design of piezoelectric energy harvester for a wide operating frequency range is a challenging problem and is currently being investigated by many researchers. Widening the operating frequency is required, as the energy is harvested from ambient source of vibration which consists of spectrum of frequency. This paper presents a new technique to increase the operating frequency range which is achieved by designing a harvester featured by a propped cantilever beam with variable over hang length. The proposed piezoelectric energy harvester is modeled analytically using Euler Bernoulli beam theory and the effectiveness of the harvester is demonstrated through experimentation. The results from analytical model and from experimentation reveal that the proposed energy harvester generates an open circuit output voltage ranging from 36.43 V to 11.94 V for the frequency range of 27.24 Hz to 48.47 Hz. The proposed harvester produces continuously varying output voltage and power in the broadened operating frequency range.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.190-190
• /
• 2000

This paper presents a multirate state feedback control (MRSFC) method for systems sensitive to disturbance and noise based on the multirate estimator design using the current estimator. MRSFC updates the controller output slower than the measurement sampling frequency of system output by a lifting factor R=T$\sub$c//T$\sub$s/. The closed-loop MRSFC system is less sensitive to disturbance and noise due to filtering effect than the conventional single-rate control system. The multirate estimator gain is obtained from solving a conventional pole placement problem such that MRSFC has the same spectrum of eigenvalues in the s-plane as the single-rate control. We applied the proposed multirate state feedback controller to a galvanometer servo system. Simulation and experimental results show that settling and tracking performances are improved compared with a conventional single-rate pole placement control (PPC).

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2434-2437
• /
• 1999

In order to detect the ultrasonic that is generated by the partial discharge of the heavy electric machinery, a Laser Doppler Vibrometer (LDV) was developed. A Michelson type interferometer which employed heterodyne signal process technique was built to measure the frequency and amplitude of vibration. The output signal of the fast photodetector was a frequency modulated signal centered at 40 MHz. The signal from the detector was amplified and downconverted to intermediate frequency centered at 1 MHz after mixing process. The voltage output that was proportional to the velocity of the moving surface(PZT) was obtained using PLL. The spectrum of the FM signal was analyzed and integration method was introduced to obtain amplitude information. This LDV can be used to measure the vibration of MEMS devices, automobiles, HDD and CDP.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.2
• /
• pp.55-60
• /
• 2006

In order to suppress lasing oscillation and obtain high light power, We have proposed a novel SLD which is formed with a straight and tilted waveguide. The window region is used to suppress lasing oscillation and reduce the facet reflectivity. High power and low reflectivity is obtained by the straight and tilted waveguide. Based on the theoretical analysis, we have fabricated the SLD with the waveguide of 500 $\mu$m length and window region of 50 $\mu$m by LPE equipment. Through the measurements of optical characteristics, the output light power of 3 mW was obtained at the 150 mA CW injection current and 25$^{circ}C$. We have confirmed that the proposed SLD has a 0.8 dB spectrum ripple lower than 1 dB which is sufficiently low reflectivity for preventing lasing.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2195-2197
• /
• 2000

In order to detect the ultrasonic that is generated by the partial discharge of the heavy electric machinery a Laser Doppler Vibrometer (LDV) is developed. A Michelson type interferometer which employed heterodyne signal process technique is built to measure the frequency and amplitude of vibration. The output signal of the fast photodetector is a frequency modulated signal centered at 40 MHz. The signal from the detector is amplified and converted to intermediate frequency centered at 1 MHz after mixing process. The voltage output that is proportional to the velocity of the moving surface(PZT) is obtained using PLL. The spectrum of the FM signal is analyzed and integration method was introduced to obtain amplitude information. This LDV can be used to measure the vibration of MEMS devices, automobiles, HDD and CDP.