• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.192-194
• /
• 2006

To elucidate possible challenges for outdoor practical use of dye-sensitized solar cells(DSC), compared with conventional Si solar cells. DSC modules still need the larger area than conventional Si solar modules to attain the same rated output because of lower photoelectron-chemical conversion efficiency. However, using batteries backup systems, the measured data shows that DSCs gathered over 12% more electricity than Si solar cells of the same rated output power in same outdoor condition. Moreover, battery charging time of DSC is about 1 hour faster than same rate of Si solar module. In this paper, 12 single DSC cells prepared for 4 serialized DSC cells was connected in 3 row parallel which have same output power rate of Si solar module. This DSC module was practiced generating characteristic experiment over outdoor daylight condition and applied with PV battery charger by using DC-DC converter. The main advantages of DSC module battery charger as compared with conventional Si solar module one are shorter charge time and lower cost.

• Current Photovoltaic Research
• /
• v.10 no.4
• /
• pp.111-115
• /
• 2022

For the high efficiency of the photovoltaic module, a high-output solar cell, which is the basis of photovoltaic power generation, is required. As the light receiving area of the solar cell increases, the light receiving area of the photovoltaic module also increases. Accordingly, recent trend is to use large-area solar cells such as M6 and M8 instead of M2-based solar cells for manufacturing the photovoltaic module and a study on the mechanical stiffness of the module with increased size is required. In this study, a mechanical load test corresponding to IEC-61215 was performed among the reliability tests of large-area photovoltaic modules. In order to confirm the degree to which the mechanical load test affects the photovoltaic module, the output and EL images were checked by sequentially increasing the pressure by 600 Pa at a pressure of 2400 Pa. Also, factors such as output and efficiency of large-area photovoltaic modules were verified through mechanical load testing of actual large-area photovoltaic modules and the rate of change was very small at 1%.

• Journal of Sensor Science and Technology
• /
• v.31 no.6
• /
• pp.376-382
• /
• 2022

A triboelectric nanogenerator (TENG) can obtain electrical output due to the reciprocal motion between two objects (i.e., rubbing), in which repetitive contact is made. High reliability, stable output, and high reproducibility are important aspects of the electrical output obtained through a TENG as a sensor or generator, thus enabling its meaningful use. Therefore, many researchers fabricated TENGs into individual parts in the form of one module type to obtain high reproducibility and reliability. Since a TENG manufactured as a module type operates as a single device, it is possible to collect kinetic energy and convert it into electrical energy through the interaction between internally configured elements without the need for a separate structure. In addition, it is relatively easy to apply the size to the body, machine tools, and natural environment by simply adjusting the size suitable for use and surrounding environmental conditions. In this paper, the application cases of module-type TENGs are divided into four areas, and the research progress of module-type TENGs in each area is extensively reviewed.

• 한국태양에너지학회:학술대회논문집
• /
• 2012.03a
• /
• pp.102-107
• /
• 2012

The purpose of thesis is to improve output of solar cell module by enhancing transmission efficiency. To improve transmission efficiency, transmission interconnection ribbon which is used to connect solar cells and busbar which contacts with it has been improved. To secure reliability, comparison research on output of solar cell modules has been conducted by manufacturing PCB module formed by laminated metal with the same output. The result of this research is based on a output efficiency test of modules by comparing electric conductivity of soldering busbar and laminated PCV type of busbar.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.53-58
• /
• 2009

Solar photovoltaic power generation system is judging that by the most suitable new refreshing energy in real condition of our country forward continuously interest for solar photovoltaic power generation system and diffusion me enlarged. Output decline problem is item to consider necessarily and should be verified in continuous interest for solar photovoltaic power generation system are diffusion. Present plan that minimize output decline calculating module liver optimum interval that consider recitation of a poem to reduce output decline by module liver shade by incidence angle consideration and this that occupy most parts among factor because do output of solar photovoltaic power generation system well.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.12-17
• /
• 2008

In this paper, an I-V characteristics of bypass diode has been studied by counting the shading effect in photovoltaic module. The shadow induces hot spot phenomenon in PV module due to the increase of resistance in the current path. Two different types of PV module with and without bypass diode were fabricated to expect maximum output power with an increasing shading rate of 5 % on the solar cell. Temperature distribution is also detected by shading the whole solar cell for the outdoor test. From the result, the bypass diode works properly over 60 % of shading per cell with constant output power. Maximum power generation in case of solar cell being totally shaded with bypass diode decreases 41.3 % compared with the one under STC(Standard Test Condition). On the other hand, the maximum output power of the module without bypass diode gradually decreases by showing hot spot phenomenon with the increase of shading ratio on the cell and finally indicates 95.5 % of power loss compared with the output under STC. Finally the module temperature measured increases around $10^{\circ}C$ higher than that under STC due to hot-spots which come from the condition without bypass diode. It has been therefore one of the main reasons for degrading the PV module and shortening the durability of the PV system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.05a
• /
• pp.121-124
• /
• 2002

This paper resents a virtual forming system to simulate deep drawing process for stress-strain information by utilizing virtual system designed using Virtual Reality Modeling Language (VRML) and computer aided analysis (CAE) tool. The CAE tool to calculate stress, strain, and deformation is designed using Finite Element Method. Stress distributions and deformation profiles as well as the operation of forming machine can be simulated and visualized in the web. The developed system consists of three modules, input module, virtual forming machine module, and output module. The input nodule was designed using HTML and ASP. The input data for FEM calculation is directed to the forming machine module for calculation. The results from the forming machine module can be visualized through output module as well as the forming process simulation.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.15 no.3
• /
• pp.45-53
• /
• 2019

Moving image sharing technology has developed various servers and programs for personal broadcasting. In this paper, we propose the method of transmitting the multiple moving image, including the output channel of external streaming server. It also implements and tests multiple real-time broadcast channel automatic transmission systems that assign multiple output channels to automatic output channels. As a result of the experiment, it is easy to allocate moving image to broadcast channels that are output through the external streaming server's output channels regardless of the size of the streaming server, enabling the management of efficient output channels at the time of transmission of multiple moving image. The moving image can be provided through streaming method regardless of the type of moving image from the moving image provider terminal, and the moving image transmission can be controlled in various ways, including adding and changing channels for which the moving image is sent, and sending delayed to the moving image.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.13 no.2
• /
• pp.171-181
• /
• 1988

In this study, a packet voice/data terminal(PVDT) that services both voice and data in the packet-switched network is implemented. The software structure of the PVDT is designed according to the OSI 7 layer architecture. The discrimination of voice and data is made in the link layer. Voice packets have priority over data packets in order to minimize the transmission delay, and are serviced by a simple protocol so that the overhead arising form the retransmission of packets may be minimized. The hardware structure of the PVDT is divided into five modules; a master control module, a speech proessing module, a speech activity detection module, a telephone interface module, and an input/output interface module. In addition to the hardware implementation, the optimal reconstruction delay of voice packets to reduce the influence of delay variance is analyzed.

• Journal of the Korea Society for Simulation
• /
• v.8 no.4
• /
• pp.1-8
• /
• 1999

This paper proposes an ATM switch architecture called Output Queued Batcher-Banyan switch (OQBBS). It consists of a Sorting Module, Expanding Module, and Output Queueing Modules. The principles of channel grouping and output queueing are used to increase the maximum throughput of an ATM switch. One distinctive feature of the OQBBS is that multiple cells can be simultaneously delivered to their desired output. The switch architecture is shown to be modular and easily expandable. The performance of the OQBBS in terms of throughput, cell delays, and cell loss rate under uniform random traffic condition is evaluated by computer simulation. The throughput and the average cell delay are close to the ideal performance behavior of a fully connected output queued crossbar switch. It is also shown that the OQBBS meets the cell loss probability requirement of $10^{-6}$.