• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.785-786
• /
• 2006

Performance comparison of IPMSMs with distributed and concentrated winding is presented in this papcr. Two IPMSMs have been designed and fabricated with identical rotor dimension, air-gap length, series turn number, stator outer radius, and axial length except winding configuration. Basic parameters and machine performance, such as resistances, back emf, output torque, and efficiency, are compared. From the comparison results, motor design considering winding configuration is discussed.

• Computers and Concrete
• /
• v.26 no.1
• /
• pp.21-30
• /
• 2020

Buckling and post-buckling behaviors of geometrically imperfect annular sector plates made from nanoparticle reinforced composites have been investigated. Two types of nanoparticles are considered including graphene oxide powders (GOPs) and silicone oxide (SiO₂). Nanoparticles are considered to have uniform and functionally graded distributions within the matrix and the material properties are derived using Halpin-Tsai procedure. Annular sector plate is formulated based upon thin shell theory considering geometric nonlinearity and imperfectness. After solving the governing equations via Galerkin's technique, it is showed that the post-buckling curves of annular sector plates rely on the geometric imperfection, nanoparticle type, amount of nanoparticles, sector inner/outer radius and sector open angle.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.2
• /
• pp.76-81
• /
• 1985

This paper presents basis functions for curvilinear square elements and describes finite element analysis for coaxial cable and coaxial cross-section waveguide. On the case of coaxial cable, the more exact results is obtained by the propotional elements than by the equal elements with the same number of elements. It is found that the cutoff frequency of coaxial cross-sectional waveguide is more dependent on the inner and outer radius than the cross-sectional angle.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.429-429
• /
• 2013

We present a systematic study of the electrical, optical and electromechanical properties of flexible graphene/metal grid hybrid transparent conductive electrodes using 4-point prove method, ultraviolet/visible spectrometer and inner/outer bending test system. The hybrid electrodes were synthesized by depositing a silver grid on a graphene surface. The sheet resistance of hybrid electrodes was as low as 30 Ω/square, while the transmittance was 90%. The electromechanical properties as a function of the change of bending radius were evaluated by measuring the change in resistance. The result will be presented in detail. We believe that these results will provide useful information for the flexible optoelectronic devices based on graphene transparent electrodes.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.1
• /
• pp.81-88
• /
• 1995

Fully developed turbulent flow through three concentric annuli with both the rough inner and outer walls was experimentally investigated for a Reynolds number range Re=15,000-85,000. Measurements were made of the pressure drop, the positions of zero shear stress and maximum velocity, and the velocity distributions in annuli of radius ratios, ${\alpha}=0.26$, 0.4 and 0.56, respectively. The experimental results showed that the positions of zero shear streess and maximum velocity were only weakly dependent on the Reynolds number. It was also found that the position of zero shear stress was not coincident with that of maximum velocity. Furthmore, the former was influenced more sensitively than the latter on the square-ribbed roughness along the axial direction.

• Journal of Integrative Natural Science
• /
• v.13 no.1
• /
• pp.1-7
• /
• 2020

This paper proposes a novel fractional frequency reuse(FFR) based on dynamic user distribution. In the FFR, a macro cell is divided into two regions, i.e., the inner region(IR) and outer region(OR). The criterion for dividing the IR and OR is the distance ratio of the radius. However, these distance-based criteria are uncertain in measuring user performance. This is because there are various attenuation phenomena such as shadowing and wall penetration as well as path loss. Therefore, we propose a novel FFR based on dynamic user classification with signal to interference plus noise ratio(SINR) of macro users and classify the FFR into two regions newly. Simulation results show that the proposed scheme has better performance than the conventional FFR in terms of SINR and throughput of macro cell users.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.864-866
• /
• 2000

In the slotted motor, cogging torque is generated due to the interaction between the rotor magnets and the slots on the stator. It is well known that cogging torque produces vibration and noise which may be detrimental to the performance of position and speed control system. Hence, the prediction of cogging torque is very important at the design stage of BLDC motor. In this paper, permanent magnets with different arc an91e of inner and outer radius is proposed. The cogging torque of proposed model and conventional one is analyzed by 2-D FEM and compared.

• Structural Engineering and Mechanics
• /
• v.58 no.4
• /
• pp.719-729
• /
• 2016

The main objective of the present paper is to study the effect of the yield criterion on the magnitude of the strain rate and plastic work rate intensity factors in axisymmetric flow of isotropic incompressible rigid perfectly plastic material by means of a problem permitting a closed-form solution. The boundary value problem consisting of the axisymmetric deformation of a plastic tube is solved. The outer surface of the tube contracts. The radius of the inner surface does not change. The material of the tube obeys quite a general yield criterion and its associated flow rule. The maximum friction law is assumed at the inner surface of the tube. Therefore, the velocity field is singular near this surface. In particular, the strain rate and plastic work rate intensity factors are derived from the solution. It is shown that the strain rate intensity factor does not depend on the yield criterion but the plastic work rate intensity factor does.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.1 no.2
• /
• pp.128-137
• /
• 1989

Numerical solutions for two-dimensional, steady, free convection are presented for a cylinder filled with saturated porous media. An annulus is bounded by inner wall with constant heat flux and two adiabatic horizontal walls with outer wall isothermally cooled. Governing equations are numerically solved for the range of Aspect Ratio 1 to 20, Radius Ratio, 1 to 20, and Rayleigh number, 50 to $10^4$ by Finite Difference method utilizing upwind scheme. Results are presented in terms of stream lines and isotherms, temperature distributions and local Nusselt numbers at the heated wall. Average Nusselt numbers are also presented for the comparisons.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.6
• /
• pp.1313-1318
• /
• 2007

When the mold is cooled suddenly to reduce the time for forming work and improve the quality of jar50ml which is different highly at rib thickness by a series of various curvature radii, the poor quality of void, flow and deformation happens. The structure of spiral cooling circuit at cavity and core can control the temperature of inner and outer side sufficiently. And the system can control cooling and heating automatically. These things are applied to Jar mold. and so, the best quality and the effect of productivity improvement can be obtained.