• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.1
• /
• pp.23-30
• /
• 2011

This study was carried out to investigate the effect of aging treatment on the mechanical properties and damping capacity of 12Cr heat resistant steel with ferrite phase. While hardness values in ferrite phase was not changed, that in martensite phase was dramatically dropped in early stage of aging treatment and then gradually decreased with increase of aging time. As aging treatment was carried out, the precipitation was not detected in ferrite phase, while carbides were precipitated in martensite phase. With increasing the aging time, tensile strength eventually decreased while impact toughness increased rapidly in the early stage of aging and then gradually increased. Besides, it was confirmed that damping capacity was not changed in the early stage of aging and then gradually increased with increase of aging time.

• Journal of the Korean Magnetic Resonance Society
• /
• v.24 no.4
• /
• pp.96-103
• /
• 2020

A new NMR method to monitor solvent-localized NMR signals in the two-phase liquid system is suggested. This method based on intermolecular single-quantum coherence (iSQC). Here, we exploited the feature of the local action of distant dipolar field (DDF) effect in order to filter out specific NMR signals dissolved in different solvents. This solvent specific iSQC spectroscopy was carried out on a model two-phase liquid system (D-glucose in water/palmitic acid in chloroform), and showed solvent-localized NMR signals. We believe our approaches might be useful in metabolic analysis such as two-phase liquid extraction scheme for labile chemical species.

• Journal of Power Electronics
• /
• v.9 no.4
• /
• pp.553-566
• /
• 2009

In-phase control and energy-optimized control are the two major control strategies proposed for series power quality controllers (SPQC). However quantitative analysis and comparison between these two control strategies is quite limited in previous publications. In this paper, an extensive quantitative analysis is carried out on these two control strategies through phasor diagram approach, and a detailed quantitative comparison is conducted accordingly. The load current is used as the reference phasor, and this leads to a simpler and clearer phasor diagram for the quantitative relationship. Subsequently detailed analysis of SPQC using in-phase control and energy-optimized control are provided respectively, under different modes both for under voltage/voltage sag and for over voltage/voltage swell. The closed form analytic expressions and the curves describing SPQC compensation characteristics are obtained. The detailed system power flow is figured out for each mode, and the detailed quantitative comparison between the two control strategies is then carried out. The comparison covers several aspects of SPQC, such as required compensating voltage magnitude, required capacity of energy storage component, and maximal ride-through time. In the end, computer simulation and prototype experimental results are shown to verify the validity of all the analysis and the result of the comparison.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.6 s.237
• /
• pp.815-821
• /
• 2005

Biaxial low cycle fatigue test was carried out to predict fatigue life under combined axial-torsional-loading condition which is that of in-phase and out-of-phase for CF8M cast stainless steels. Fatemi-Socie(FS) parameter which is based on critical plane approach is not only one of methods but also the best method that can predict fatigue life under biaxial loading condition. But the result showed that, biaxial fatigue life prediction by using FS parameter with several different parameters for the CF8M cast stainless steels is not conservative but best results. So in this present research, we proposed new fatigue life prediction parameter considering effective shear stress instead of FS parameter which considers the maximum normal stress acting on maximum shear strain and its effectiveness was verified.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.8
• /
• pp.377-386
• /
• 2005

This paper presents the control algorithm of single-phase hybrid active power filter for the compensation of harmonic current components in nonlinear R-L load with passive active Power filters. To construct two phase system, an imaginary second phase was made. In this proposed method, the new signal which is the delayed through the filtering by the phase-delay property of low-pass filter is used as the secondary phase. Because two-phases have the different phase, the instantaneous calculation of harmonic current is possible. In this paper, a reference voltage is created by multiplying the coefficient k by the compensation current using the rotating reference frame synchronized with the source-frequency, not applying to instantaneous reactive power theory which has been used with the existing fixed reference frames In order to verify the validities of the proposed control methods, experiments are carried out with the prototypes of single-phase hybrid active power filter.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.6
• /
• pp.320-328
• /
• 2003

A specimen of Cu-35%Sn alloy has been subjected to the unidirectional heat treatment in an attempt to examine the evolution of microstructures under varying thermal conditions. The specimen was cast in the form of a cylinder 10 mm in diameter and 200 mm in length, which was then installed in the temperature gradient field established inside a vertical tube furnace. The furnace temperature was adjusted to make the upper part at $750^{\circ}C$ and bottom end part at $300^{\circ}C$ of the specimen. The experiment was terminated by dropping it into water after the 30 minutes holding at given temperature. By the rapid cooling, the high temperature phases, ${\gamma}$ and ${\zeta}$, were retained at ambient temperature with some of ${\gamma}$ phase transformed to ${\varepsilon}$ phase, especially at the grain boundaries of ${\gamma}$ phase. The presence of ${\varepsilon}$ phase was found to determine the nature of phase transformations of the ${\zeta}$ phase undergoes upon cooling. In the close area of the ${\varepsilon}$ phase, ${\varepsilon}$ phase grew separately out of ${\zeta}$, and adds to the preexisting ${\varepsilon}$ whereas in areas away from ${\varepsilon}$, both ${\delta}$ and ${\varepsilon}$ grew simultaneously out of ${\zeta}$, and formed a lamella eutectoid structure. The transformation to ${\delta}$ was found to occur only in slow cooling. The hardness on each phase showed that the retained phases, ${\gamma}$ and ${\zeta}$, could be plastically deformed without brittle fracture while the phases, ${\varepsilon}$ and ${\delta}$, were too brittle to be deformed.

• Progress in Superconductivity and Cryogenics
• /
• v.6 no.3
• /
• pp.50-55
• /
• 2004

We fabricated and tested a resistive type superconducting fault current limiter (SFCL) of three-phase 6.6 $kV_{rms}/200 A_{rms}$ rating based on YBCO thin films grown on sapphire substrates with a diameter of 4 inches, Short circuit tests were carried out at a accredited test facility for single line-to- ground faults, phase-to-phase faults and three-phase faults, Each phase of the SFCL was composed of 8${\times}$6 elements connected in series and parallel respectively. Each element was designed to have the rated voltage of 600 $V_{rms}$. A NiCr shunt resistor of 23 Ω was connected to each element for simultaneous quenches. Firstly, single phase-to-ground fault tests were carried out. The SFCL successfully developed the impedance in the circuit within 0.12 msec after fault and controlled the fault current of 10 $kA_{rms} below 816 A_{peak}$ at the first half cycle. In addition, in case of phase-to-phase fault and three- phase fault test. simultaneous quenches among the SFCLs of the phases successfully accomplished. In conclusion. the SFCL showed excellent performance of current limitation upon fault and stable operation regardless of the amplitude of fault currents.

• Journal of Embryo Transfer
• /
• v.17 no.2
• /
• pp.91-100
• /
• 2002

The experiment was divided into two phases. In phase-I fresh embryos were transferred and in Phase-II frozen embryos were transferred. Embryos were collected by using Dulbecco's phosphate buffered saline. In phase-I total of 65 ova were collected out of 107 ovulation in 18 goats. Recovery of ova was 60.74％, of which 51 (78.46％) was fertilized. Sixteen embryos were transferred to 10 recipient goats and kidding was observed in 6 goats, that produced 10 kids. Thus, 62.50％ embryo survival and 60％ kidding were achieved in phase-I. In phase-II of the experiment, 17 regular cyclic Black Bengal goats were used. The main purpose was to study the viability of caprine embryos after cryopreservation. In this phase the embryos were collected and frozen using Bio-cool freezers. A two step addition of cryoprotectants (5％ glycerol and 10％ glycerol) and three-step dilution of cryoprotectants with 1mole (M) sucrose was used. Embryos were preserved for 10 to 45 days. Out of 27 embryos preserved, 18 were recovered after freezing and thawing (37$^{\circ}C$ water bath) with 33.33％ embryonic loss. Seventeen frozen and thawed embryos were transferred in 9 recipient goats, out of which kidding was observed in 6 goats and 7 kids were produced, giving a 66.66％ kidding and embryo survival of 41.17％. The technique utilized for fresh and frozen embryo transfer can be successfully utilized to produce goats of superior genetic merits. The protocol used for addition of cryoprotectant, freezing, thawing and dilution was found suitable for caprine embryo freezing.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.141-150
• /
• 1994

The residual stress is inevitably introduced into composites because of the mismatch of the coefficient of thermal expansion, and it is different in each phase. The X-ray technique can detect separately the stress in each phase, so will wield useful information for analyzing the toughening mechanisms of composites. In order to apply the law of mixture to alloy steels with composite microstructures, two phase stainless steel, consisted of ferrite (.alpha.-Fe) and austenite (.gamma.-Fe) structures, was selected. The tensile elastic deformation was loaded, and then the X-ray diffraction technique was used to measure the X-ray elastic constants, the X-ray stress constants and the phase stresses. The law of mixture was investigated and the separation of macrostress and microstress was carried out. The phase stresses (the residual stresses of phase) in each phase, which were measured by X-ray technique, was directly proportional to the applied stress. The macrostress calculated from the phase stresses by using the law of mixture was nearly equal to the applied stress.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.4
• /
• pp.11-14
• /
• 2001

Phase intergrowth in BSCCO thin films has been Investigated. It turfed out from XRD analyses of these phases that molar fraction of each constituent phase in the intergrowth thin film can be exhibited as a function of substrate temperature and ozone pressure. Super- conducting behavior of the intergrowth thin aim Is also discussed.