• Fibers and Polymers
• /
• 제5권3호
• /
• pp.177-181
• /
• 2004

Current efforts to establish links between geometrical features and mechanical performance of nonwoven fabrics in general, and of point-bonded (spot-bonded) nonwovens in particular has been made using the measurements of Fiber Orientation Distribution Function (ODF) and tensile modulus which occurs during controlled-deformation experiments. Image analysis technique (using the Fast Fourier Transform) was used to quantify the fiber orientation distribution. The results suggest that, within a typical window of processing conditions, the fiber orientation has a significant influence on the anisotropical behavior of nonwoven. The data also suggest that mechanical anisotropy of thermally point-bonded nonwovens is likely to be governed by different load transfer mechanism according to the applied macroscopic tensile direction.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 The Korea-Japan Joint Symposium
• /
• pp.75-76
• /
• 2003

Current efforts to establish links between geometrical features and mechanical performance of nonwoven fabrics in general, and of point-bonded (spot-bonded) nonwovens in particular, would be served significantly by the measurements of Fiber Orientation Distribution Function (ODF) and tensile modulus which occurs during controlled-deformation experiments. Image analysis technique (using the Fast Furier Transform) is used to quantify the fiber orientation distribution. The results suggest that, within a typical window of processing conditions, ODF has a significant influence on the mechanical anisotropy. The data also suggest that mechanical anisotropy of thermally point-bonded nonwovens is likely to be governed by different stress mode according to the applied macroscopic tensile direction.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.105-108
• /
• 2003

Sheets of aluminum alloy 1100 were asymmetrically cold rolled in a rolling mill with different roll speeds. In order to promote the shear deformation during asymmetrical rolling, cold rolling without lubrication was performed. The evolution of texture components during asymmetrical rolling was investigated by the calculation of the orientation distribution function (ODF) using the monoclinic sample symmetry. The strain state during asymmetrical rolling was tackled by means of FEM calculations. Asymmetrical rolling gave rise to the development of pronounced strain gradients throughout the thickness layers which resulted in the formation of strong texture gradients in the aluminum sheet.

• 소성∙가공
• /
• 제12권3호
• /
• pp.244-250
• /
• 2003

Sheets of aluminum alloy 1100 were asymmetrically cold rolled in a rolling mill with different roll speeds. In order to promote the shear deformation during asymmetrical rolling, cold rolling without lubrication was performed with a roll speed ratio of 1.5/l.0. The evolution of texture components during asymmetrical rolling was investigated by the calculation of the orientation distribution function (ODF) using the monoclinic sample symmetry. The strain state during asymmetrical rolling was tackled by means of FEM calculations. Asymmetrical rolling gave rise to the development of pronounced strain gradients throughout the thickness layers which resulted in the formation of strong texture gradients in the aluminum sheet.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 추계학술대회논문집
• /
• pp.149-152
• /
• 1999

The effect of initial orientation on the microstructure and texture evolution of two ferritic stainless steels was investigated. the columnar and equiaxed crystal specimens which were prepared from continuous casting slab were hot rolled annealed cold rolled and annealed respectively. The rolling and recrystallization textures at each process stage were examined by orientation distribution function (ODF) and electron back-scattered diffraction (EBSD); The observation showed that the orientation density of the $\alpha$-fibre of hot rolled band of columnar crystal specimen was more pronounced than that of the equaxed one at the center layer. Nevertheless the cold rolled textures of Type 430 steel have demonstrated a rather similar development . Compared to Type 430 steel the development of the $\alpha$-fibre in the center layer of Type 409L steel was much more pronounced. The relation between texture evolution and ridging behaviour has been discussed.

• 열처리공학회지
• /
• 제24권5호
• /
• pp.251-261
• /
• 2011

The changes in microstructure and texture during annealing were examined in a series of 0.015% C-1.5% Mn cold-rolled sheet steels with 0~0.5% Mo. Orientation distribution function data were calculated from the (110), (200), (211) pole figures determined on the rolled plane of cold-rolled and annealed steel sheets. Regardless of Mo content and annealing conditions, martensite volume fraction was less than 1.0%, not affecting the texture evolution. Textural change at the cooling stage after heating at $820^{\circ}C$ for 67 sec was not observed. Increasing the Mo content and annealing temperature markedly strengthened the intensities of ${\gamma}$-fiber texture, resulting in the increase in $r_m$ value. The desirable texture evolution for deep drawability in the 0.5% Mo steel may be mainly caused by the grain refining effect of Mo carbide in the hot-rolled steel sheet.

• 한국세라믹학회지
• /
• 제43권3호
• /
• pp.152-155
• /
• 2006

Silicon carbide ceramics seeded with 10-30 wt% SiC whiskers are fabricated by hot pressing and annealing. A quantitative texture analysis including calculation of the Orientation Distribution Function (ODF) is used for obtaining the degrees of preferred orientation of the fabricated samples. The microstructure and crystallographic texture are discussed with respect to the effect of ${\beta}-SiC$ whisker seeds on the resulting fracture toughness values. The SEM microstructures and the texture data reveal a correlation between texture and fracture toughness anisotropy.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.460-462
• /
• 2005

Asymmetrical rolling was performed with different working roll speeds of upper and lower rolls. In order to promote the shear deformation during asymmetrical rolling, various deformation parameters of initial sheet thickness, rolling reduction, roll speed ratio and roll radius are considered. The evolution of texture during asymmetrical rolling was shown by the calculation of orientation distribution function (ODF). The effect of deformation parameters on shea. deformation were investigated by simulations with the finite element method (FEM). Asymmetrical rolling gave rise to the development of pronounced strain gradients throughout the thickness layers which resulted in the formation of strong texture gradients in the sheet.

• 소성∙가공
• /
• 제26권3호
• /
• pp.150-155
• /
• 2017

To obtain the Goss texture, {110}<001>, IF steel sheets were asymmetrically rolled by 50-89% reduction in the thickness at room temperature and subsequently annealed at 200, 900, and $1200^{\circ}C$ in a box furnace under air atmosphere. The asymmetrically rolled specimens and annealed specimens show well-developed Goss texture, {110}<001>. After the IF steel sheets were asymmetrically rolled at room temperature and subsequently annealed at $900^{\circ}C$ for 1 h in a box furnace under air atmosphere, the intensity of the Goss texture, {110}<001> was high in the IF steel sheets.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.46-49
• /
• 2002

The aim of this paper is to investigate the influence of various deformation ratio on texture of Ag tapes that can be used as a RE-$Ba_2Cu_3O_{7-{\delta}}$ coated conductor tapes without any buffer layer. We fabricated as-rolled Ag substrate with various deformation ratio per step. Thickness and total deformation ratio of Ag tapes were $100{\mu}m$ and >98%, respectively. And as-rolled Ag substrate was annealed at $750^{\circ}C$ for 30min. The as-rolled and recrystallization textures were measured using x-ray pole figures and orientation distribution function (ODF) analysis. With the increase of rolling ratio from 5 to 20%, deformation texture are changed from {1l0}<311> to {1l0}<112>, {032}<100>, {051}<211>. After recrystallization by annealing, main texture was observed to {013}<100> under present condition.