• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.6A
• /
• pp.561-572
• /
• 2010

This paper is a study about application of recently proposed Performance Based Mixture Design (PBMD) for design of high strength concrete (HSC) to obtain HSC mix proportion that satisfies required performances. The PBMD method which uses Satisfaction curve based on a Bayesian method is a performance oriented concrete mix proportion design procedure easily applicable to any condition and environment for a possible replacement to the current prescriptive design standards. Based on extensive experimental results obtained for various materials and performance parameters of HSC, the application feasibility of the developed PBMD procedure for HSC has been verified. Also, the proposed PBMD procedure has been used to perform application examples to obtain desired target performances of HSC with optimum concrete mixture proportions using locally available materials, local environmental conditions, and available concrete production technologies. The validity and precision of HSC mix proportion design obtained using the PBMD method is verified with the experimental and ACI presented results to check the feasibility for actual design usage.

• Culinary science and hospitality research
• /
• v.20 no.6
• /
• pp.235-244
• /
• 2014

The purpose of this study was to investigate the effect of freezing and thawing rate on the physical properties of soybean sprouts to improve the quality of processed soybean sprouts during distribution and storage. Cooked soybean sprouts were frozen by air-blast freezing (ABF) system at $-45^{\circ}C$ or natural air convection freezing (NCF) system at $-24^{\circ}C$, then thawed using microwave oven by varying output power (0, 400, 800 and 1,000 W) until $75^{\circ}C$. The quality of soybean sprouts was measured by the water content, hardness and springiness. In addition, the internal microstructure of soybean sprouts was observed by optical microscope. For results, water content of soybean sprouts thawed by 1,000 W in a microwave showed the lowest value after natural air convection freezing. Springiness of soybean sprouts thawed by all amounts of output power was decreased in comparison with control. Hardness was increased only in soybean sprouts thawed by 1,000 W after air-blast freezing. However the gaps between springiness and hardness were relatively small with control at 1,000 W thawing, after air-blast freezing. Internal microstructure of the soybean sprouts was more damaged as freezing and thawing time were increased. In conclusion, high freezing and thawing rate might improves the quality of soy bean sprout, and IQF freezing and 1,000 W of microwave thawing appears to be the optimum condition for frozen HMR production. From the results freezing and thawing process parameters might can be use as quality control parameters as various type of sprout products processing.

• Korean Journal of Soil Science and Fertilizer
• /
• v.7 no.3
• /
• pp.163-175
• /
• 1974

Effects on yields, yield components and nutrient content of potassium depression for two or three weeks at various growth stages were investigated in rice (var. Jinheung) under sand culture system.(K 40 ppm 1973) 1. Analysis of variance showed significant difference among treatments of both two-week (at p=0.01) and three-week depression (at p=0.05) in yield. 2. Most sensitive stage to potassium depression on yield appeared two weeks until heading (42% yield decrease) and sensitivity decreased the growth stage is apart from heading either before or after. During 30 days after transplanting two-week potassium depression increased yield, but three-week depression decreased yield. Until about 30 days after heading depression caused poor yield. 3. Root potassium involves in harvest index, filled grain ratio and grain weight with significant correlation and considerably in spikelet per panicle while potassium in leaf sheath+culm involves considerably in spikelet per panicle and panicle per hill. Relative total dry matter weight was significantly correlated with panicle per hill, spikelet per panicle and K or K/Ca+Mg only in leaf sheath+culm. The indications are that root potassium contributes for building sink and efficiency of structure while potassium in leaf sheat+culm primarily for building source, productive structure. 4. Relative yield was significantly correlated with potassium content in root and leaf sheath+culm and with K/Ca+Mg and its ratio before and after depression in root indicating that potassium depression occurs greatly in root and that K/Ca+Mg might have more important role than K content alone under depression. 5. Optimum level of $K_2O$ appears around 3% in leaf blade. 4% in leaf sheath+culm and 1% in root under the assumption that below these level the same content has the same role in relation to yield during growth. The K/Ca+Mg appeares to be 2.5 in root and should not decrease throughout the growth stages. 6. The increase of sodium content in plant by K depression was highest, especially in leaf sheath during the most insensitive period to K depression suggesting that insensitivity may be attributed to partial replacement of Na for K. Partial replacement seems very little in sensitive stage (later stage) and sensitive organ (root).

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.9
• /
• pp.39-45
• /
• 2010

Controlled low strength material(CLSM) is produced by mixing portland cement, fine aggregates, water and chemical admixtures. Sand is the most commonly used as the fine aggregates in the conventional CLSM. It is getting more and more difficult to obtain sand in Korea so it is required that the alternative materials be developed as the replacement of sand. Since the engineering characteristics of coal ash are similar to the sand, it becomes necessary to examine the application of the coal ash as the alternative material for CLSM and as the environment-friendly material. When the results meet the optimum pH level that plants can live, it can be expanded the scale of application of the study on the plant as the important field. This study was subjected to present the method to reduce the pH range of CLSM to a suitable condition that plants can survive. To verify this method, the care of neutralization was conducted by immersing the specimen to Ammonium monohydrogen phosphate. Before curing and neutralization, the maximum pH of developmental CLSM is approximately 11. However, the pH value of developmental CLSM has under 9.5 after peaceful curing and neutralization management.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.6D
• /
• pp.839-848
• /
• 2011

TBM (Tunnel Boring Machine) tunnel should be carry out with the adopted machine until the end of excavation because of impossibility of replacement or modification of machine. Observation of the face of the tunnel is difficult, especially in EPB(Earth Pressure Balance) shield TBM, predict changes in the ground condition with analyzing data, collected during the excavation, and it should be reflected in construction. Until recently, subjects of studies on TBM are mainly the determination of machine and the development of advance rate prediction model, according to the characteristics of ground which is the target of excavation. However, study focused on the estimation of ground conditions and the improvement in operational methods using excavation data of TBM equipment, the principal of the excavation, has been done not so much. This study examine the variances in advance rate depending on changes in operating conditions and evaluate the optimal operating conditions of adopt machine, using working data obtained from EPB shield TBM project. The result of this study is suggested as follows. First, cutter head RPM and total thrust force are biggest influences on advance rate, Second, it is recommended for proper advance rate that total thrust force is controlled while optimum cutter head RPM is kept, Third, according to the increasing trend of total thrust force, the changes in ground conditions can be predicted, the appropriate operating conditions can be determined.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.9
• /
• pp.1268-1273
• /
• 2011

The present study was conducted to determine a feasible method of protein concentrate extraction from rice bran (RBPC) and its effect as a substitution for skim milk in early weaning pig diets. An investigation to extract protein concentrate from full fat rice bran was undertaken to determine the best ratio of water and rice bran, the amount of NaOH and a HCl solvent to use in a simple paddle-type mixer with modified spinning to produce RBPC. The results stated that the best ratio for water mixing in the RBPC extraction process was 1:5 with 20 g NaOH and 30 min in a paddle-type mixer at 300 rpm. A mix of 250 ml 0.2 N HCl was optimum for neutralization and protein precipitation. After the fluid was spun out with a washing machine, the sediment was left for 12-14 hours to complete the filtration. One kilogram of rice bran could produce an average of 324.5 gram RBPC and it contained 3.40% ash, 496.48 kcal of GE/100 gram, 1.94% crude fiber, 28.20% ether extract, 7.64% moisture and 16.66% crude protein, respectively. A total of 45 crossbred piglets, weaned at 3 weeks of age were allotted into control diet (A) and dietary treatments formulated with a four different rates of RBPC substitution for skim milk at a percentage of 25 (B), 50 (C), 77 (D) and 100 (E) respectively, in a randomized complete block (RCB) design. All piglets had free access to feed and water until 8 week of age when the experiment ended. Feed intake, average daily gain, growth rate and feed efficiency were not affected by dietary treatments. Blood test parameters after completion of the growth trial indicated normal health. Even though the mean of cell hemoglobin concentration was significantly different between treatments (p<0.05) it was still within the normal range. The cost difference for BW gain of 100% RBPC substituted for skim milk in the weaning diet was approximately 35% lower than that of the control and the relative cost of production was 96.67, 92.85, 70.75 and 64.48% lower for the replacement of 25, 50, 75 and 100% of skim milk respectively. These results implied that this technology is feasible for use by small scale farmers to improve their self-reliance.

• Steel and Composite Structures
• /
• v.34 no.5
• /
• pp.681-698
• /
• 2020

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D₃ with PVD-TiN coated (Al₂O₃-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L₁₈ orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al₂O₃+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.3
• /
• pp.396-403
• /
• 2009

Male broiler chicks were fed graded levels of organic zinc (zinc-methionine) supplementation to investigate the effects of partial or complete substitution of the organic zinc source for inorganic ones on the development of lymphoid organs and immunological responses. A total of 450 day-old male broilers were distributed into groups of 10 chicks and randomly assigned to nine experimental diets during a 42-day feeding trial. Dietary treatments consisted of two basal diets supplemented with 40 mg/kg added zinc as feed-grade Zn sulfate or Zn oxide in which, Zn was replaced with that provided from zinc-methionine (ZnMet) complex at the levels of 25, 50, 75 or 100%. Two randomly-selected birds from each pen replicate were bled and then slaughtered by cervical cutting on the final day of the trial to measure leukocyte subpopulations and relative weights of lymphoid organs. Among lymphoid organs, only thymus weight was affected (p<0.05) by dietary treatments. The sulfate-supplemented birds were heavier (p<0.01) in relative weight of thymus than oxide-supplemented birds. The 10 days of age-assessed cutaneous hypersensivity reaction was stronger in chicks fed ZnMet-containing diets. Dietary ZnMet supplementation caused (p<0.05) an increase in proportion of lymphocytes and consequently a decrease in heterophil to lymphocyte ratio. Diet fortification by zinc-methionine complex increased (p<0.01) Newcastle antibody titer at 19 days of age. Also, a similar response was observed in antibody titers at 6 and 12 d after infectious bronchitis vaccine administration. There was no significant effect of replacement of dietary zinc on antibody titer against infectious bursal disease virus (IBDV) at the 6th d post-vaccine inoculation; however, at d 12 after vaccination, ZnMet-fortified diets improved antibody titer against IBDV. Although dietary inclusion of ZnMet had no marked effect on primary antibody titer against sheep erythrocytes, effective responses were observed during secondary reaction from the viewpoint of both total antibody and immunoglobulin Y (IgY) titers. From the present findings, it can be concluded that dietary supplementation with organic zinc improves both cellular and humoral immune responses. It is necessary to replace 75% of supplemental inorganic zinc with organic ZnMet complex to achieve the optimum immunological responses in broiler chicks.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.45 no.2
• /
• pp.146-153
• /
• 2012

This study examined the effect of formulated diets (composed of condensed freshwater $Chlorella$ or $Schizochytrium$ sp., $Crypthecodinium$ sp., and EPA oil sources derived from baker's yeast) on the population growth and fatty acid composition of the brackish water flea ($Diaphanosoma$ $celebensis$) to determine diet effectiveness for mass production. Results indicated that the highest maximum density, fecundity, and population specific growth rate (SGR) of the flea were observed using a diet of $Tetraselmis$ $suecica$ (control). However, results using condensed freshwater $Chlorella$ and the mixed treatment of $Schizochytrium$ sp.+$Crypthecodinium$ sp.+EPA oil did not significantly differ from the control treatment ($P$>0.05). Thus, $T.$ $suecica$ could be replaced with a combination diet of $Schizochytrium$ sp., $Crypthecodinium$ sp., and EPA oil in condensed freshwater $Chlorella$ without growth interruption of $D.$ $celebensis$. As the percentage of combination diet (mix of $Schizochytrium$ sp., $Crypthecodinium$ sp., and EPA oil) in condensed freshwater $Chlorella$ increased, the level of ARA, EPA, DHA, and n-3 HUFA in $D.$ $celebensis$ also increased. However, the population density of $D.$ $celebensis$ sharply decreased with the use of treated supplements C5M5 (CHL [50%] and $Crypthecodinium$ sp.+ $Schizochytrium$ sp. + EPA oil [MIX 50%]). The optimum proportions of CHL and MIX for $D.$ $celebensis$ within the mixture were 70% and 30%, respectively. Based on the results, the combination of $Schizochytrium$ sp., $Crypthecodinium$ sp., and EPA oil in condensed freshwater $Chlorella$ appears to be a stable and effective food source for mass production of $D.$ $celebensis$.

• Journal of the Korea Concrete Institute
• /
• v.28 no.4
• /
• pp.435-444
• /
• 2016

In Korea, approximately 48% of all households live in apartments, which are a form of multi-unit dwellings, and this figure increases up to 58%, when row houses and multiplex houses are included. As such, majority of the population reside in multi-unit dwellings where they are exposed to the problem of floor impact noise that can cause disputes and conflicts. Accordingly, this study was conducted to manufacture a high-weight, high-stiffness foamed concrete in order to develop a technology to reduce the floor impact noise. For the purpose of deriving the optimum mixing ratio for the foamed concrete that best reduces the floor impact noise, the amounts of the foaming agent, lightweight aggregate and binder were varied accordingly. Also, the target characteristics of the concrete to be developed included density of over $0.7t/m^3$, compressive strength of over $2.0N/mm^2$ and thermal conductivity of under 0.19 W/mK. The results of the experiment showed that the fluidity was very excellent at over 190 mm, regardless of the type and input amount of foaming agent and lightweight aggregate. The density and compressive strength measurements showed that the target density and compressive strength were satisfied in the specimen with 50% foam mixing ratio for foamed concrete and in all of the mixtures for the lightweight aggregate foamed concrete. In addition, the thermal conductivity measurements showed that the target thermal conductivity was satisfied in all of the foamed concrete specimens, except for VS50, in the 25% replacement ratio case for Type A aggregate, and all of the mixtures for Type B aggregate.