• Journal of KSNVE
• /
• v.5 no.2
• /
• pp.225-234
• /
• 1995

In this study, first, transformation process of damping ratios, whose are evaluated in active control analysis, into damping matrix resulting from installed viscous dampers is illustrated. Then, a method is followed to maximize the effect of response reduction, which leads to optimum locations and size of viscous dampers using sensitivity analysis. Highly coupled nonlinearity between damping ratios and dampers makes it hard to find the optimal size of dampers. Therefore, the nonlinearity is transformed to linear problem with small increments of damping ratios and the size of dampers can be found. However, there are many cases for the size of dampers satisfying the small increment of damping ratios, so it is necessary to select minimum size using optimization technique. To determine optimum locations of dampers, dampers are assumed to be installed between the different stories and their locations are selected corresponding corresponding to the degree of damping size. Numerical examples for the frame structure and the shear wall structure show that optimum locations and size of dampers are different form each other depending on the characteristics of modal responses of the structures. The proposed method in this study can be applied to get optimum locations of active controller in the active control.

• Journal of Industrial Technology
• /
• v.27 no.B
• /
• pp.161-167
• /
• 2007

The objetives of this study are to set up optimum extraction temperature, time and organic solvent for propolis extraction, to investigate chemical properties, and to develop health foods from propolis preparation. In this study, ethanol and ultrasonic extracts method performed to optimum extraction temperature was at 60, $20^{\circ}C$, optimum extraction time was at 12, 4 hours and optimum extraction amount of solvent was at 20, 15 times of propolis weight. When various ethanol solutions were used, whereas flavonoid content was highest in 70, 80% aqueous ethanol, respectively. So the ultrasonic extracts method used gave better results than the ethanol extracts method in this work. Extraction of propolis with etanol and ultrasonic extracts method was performed by using the water and various concentrations of aqueous ethanol as solvent. Sensitivity of propolis samples to Staphylococcus aureus was investigated and the results were shown. Samples of water extract did not inhibit microbial growth, where as 50% aqueous ethanol extract the largest inhibitory zone for Staphylococcus aureus, then decreased inhibition with increasing ethanol concentrations.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.12
• /
• pp.24-29
• /
• 1997

Recently, Genetic Algorithm(GA), which is a stochastic direct search strategy that mimics the process of genetic evolution, is widely adapted into a search procedure for structural optimization. Contrast to traditional optimal design techniques which use design sensitivity analysis results, GA is very simple in their algorithms and there is no need of continuity of functions(or functionals) any more in GA. So, they can be easily applicable to wide area of design optimization problems. Also, owing to multi-point search procedure, they have higher porbability of convergence to global optimum compared to traditional techniques which take one-point search method. The methods consist of three genetics opera- tions named selection, crossover and mutation. In this study, a method of finding the omtimum size and topology of drilling machine is proposed by using the GA, For rapid converge to optimum, elitist survival model,roulette wheel selection with limited candidates, and multi-point shuffle cross-over method are adapted. And pseudo object function, which is the combined form of object function and penalty function, is used to include constraints into fitness function. GA shows good results of weight reducing effect and convergency in optimal design of drilling machine.

• Economic and Environmental Geology
• /
• v.19 no.4
• /
• pp.297-304
• /
• 1986

Earthquake disaster is dependent upon both site intensity and strength of structures. The higher the strength, structures become more safe, which in turn increases the construction cost. Therefore, it is necessary to decide an optimum design intensity in which the safety is balanced with the cost. Such an optimum design intensity for major man-made structures in Korea is determined in the present study from a simulation model as follows. 1) Hypothetical earthquake time series are generated from the probability distribution to represent appropriately the seismicity of Korea. 2) The strength of structures constructed with a certain design intensity is assumed to exponentially decrease with the elapsed time. The construction cost is also expressed as a function of design intensity. 3) Comparing the seismic intensity generated from the earthquake time series with the strength of structures, the safety of structures is examined. Then the time until the structure is damaged by an earthquake is obtained within the designed life time. 4) The above simulation is iterated several hundred times and hence the mean life time of structures having a certain design intensity is obtained. 5) After all, the optimum design intensity to minimize the annual mean loss, the ratio of construction cost to mean life time, is estimated. The major conclusions obtained from the above simulation model are as follows. 1) Depending upon the designed life time ($T_p$), the optimum design intensities are appeared to be 0. 05-0. 10g for $T_p=50yr$ and 0. 08-0.13g for $T_p=100yr$. 2) According to the sensitivity analysis, the optimum design intensity increases with the rapid strength decrease of structure and decreases with the increase of initial construction cost.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.2
• /
• pp.168-172
• /
• 2005

A novel cogging torque reduction algorithm is presented for 2-pole permanent magnet DC motor. While the shape of the permanent magnet is changed in the conventional method, the pole shape of the magnetizing yoke is optimized in the presented algorithm. In order to parameterize the shape of the yoke, and the distribution of the residual magnetization of the permanent magnet, the Bezier spline is used. The shape of the magnetizing yoke is optimized using the design sensitivity analysis incorporated with the finite element method and Bezier spline.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.281-282
• /
• 2002

To reduce the spin-off of lubricants on a magnetic disk, which is caused by the radial component of shear force between the disk and air, we analyzed the air-velocity distribution and the air-shear force by three-dimensional large-eddy simulation (LES). This sensitivity analysis, on five design parameters, showed that disk/arm clearance and arm thickness have a greater effect on the mean radial air-shear force than the other parameters. The force on a disk optimized according to the optimum parameters is 12% less than the force on a conventional disk.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.4
• /
• pp.372-379
• /
• 1990

The effect of primary solidification phase on the solidification cracking sensitivity, corrosion resistance and toughness at cryogenic temperature was investigated for the austenitic stainless steel welds. The conclusions were summarized as follows; 1. Soldification crack sensitivity of austenitic stainless steel welds depends on the primary solidification mode. 2. Austenitic stainless steels were very susceptible to solidification cracking in case of solidification as primary ${\gamma}$ and immune when solidified as primary $\delta$. 3. When the ratio of Creq/Nieq is in the range of 1.46 to 1.55, the most resistance against solidification cracking was obtained. These results agreed well with the relationship between primary solidification mode, corrosion resistance and toughness at cryogenic temperature. 4. Optimum toughness, corrosion and solidification cracking resistance can be obtained when alloys having chemical compositions described above and solidifies as primary $\delta$ containing no ferrite at room temperature.

• Structural Engineering and Mechanics
• /
• v.4 no.4
• /
• pp.425-436
• /
• 1996

An application of the perturbation method to optimum structural design with random parameters is presented. It is formulated on the basis of the first-order stochastic finite element perturbation method. It also takes into full account the stress, displacement and eigenvalue constraints, together with the rates of change of the random variables. A method for calculating the sensitivity coefficients in regard to the governing equation and the first-order perturbed equation has been derived, by using a direct differentiation approach. A gradient-based nonlinear programming technique is used to solve the problem. The numerical results are specifically noted, where the stiffness parameter and external load are treated as random variables.

• Journal of the Korean Ceramic Society
• /
• v.29 no.6
• /
• pp.441-450
• /
• 1992

The microstructur and LPG sensing properties of maghemite (${\gamma}-Fe_2O_3$) ceramics have been studied. The acicular and fine spherical shaped iron oxide particles were sintered at below $900^{\circ}C$. The maghemite ceramics were prepared by reduction-oxidation of sintered iron oxide. With the microstructure of acicular and/or fine grains, the maghemite ceramics have good LPG sensing properties. Increased sintering temperature deteriorates the LPG sensitivity of maghemite ceramics due to the grain growth. The maghemite ceramics prepared from the mixed iron oxide, of a large amount of acicular particles and a small amount of spherical ones, have a lower LPG sensitivity than that of the acicular iron oxide ceramics. But, they seem to be of higher mechanical strength. The optimum working temperature for LPG sensing of the maghemite ceramics was found to be $300~350^{\circ}C$.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.89-93
• /
• 1997

A superlastic material, aluminum - lithium alloy 8090, were examined with uniaxial tensile test to investigate its thermomechanical behavior. The tests were carried out at the strain-rates ranging from 2${\times}$10-4 to 1${\times}$10-2 and at the temperatures from 48 0$^{\circ}C$ to 540$^{\circ}C$. The experiments produced force-displacement curves which converted to stress-strain curves. From the curves, several important superplastic factor such as strain-rate sensitivity, optimum strain-rate and strength coefficient were obtained.