• 한국미생물·생명공학회지
• /
• 제19권4호
• /
• pp.398-404
• /
• 1991

효모를 Na-alginate에 고정화한 후 연속반응기를 이용한 glucose 발효로 에탄올을 생산하였다. 그 결과 고정화 효모의 활성화 시간은 20~25시간이었다. 연속발효에서 고정화효모의 온도안정성은 30~$37^{\circ}C$였으며 pH 안정성은 pH 4.0~pH 8.0, 최적 희석속도는 $0.2h^[-1}$ 이었고 에탄올생산 최적 당농도는 15%였다. 최적조건에서 에탄올수율은 0.23, 생산된 에탄올 농도는 33.90g/l 그리고 에탄올 생산성은 7.12g/$l\cdot h$로 각각 나타났다.

• 한국추진공학회지
• /
• 제9권4호
• /
• pp.1-8
• /
• 2005

과산화수소를 단일추진제로 사용하는 마이크로 추력기를 위한 실험적 연구를 수행하였다. 연구에서 은 촉매 활성화 방법과 메조스케일 반응기의 성능평가에 관한 실험을 하였다. 시도한 여러 가지 활성 방법 중, $500^{\circ}C$의 수소 환원법의 경우 가장 좋은 반응성을 가짐을 확인 하였다. 추진제의 완전한 분해 조건을 찾기 위해 메조스케일 반응기가 제작되었다. 촉매 베드를 위해 지지체로 20 mm 길이의 유리 웨이퍼를 준비하여 은 촉매를 스퍼터링 하였다. 과산화수소 공급 유량에 따라 반응기내 공간시간이 변하므로 유량을 변화시키며 반웅기 실험을 수행하였고 전환율을 측정 하였다. 20 mm 베드 길이에서 추진제의 완전한 분해를 위해 480초 이상의 공간시간이 요구된다.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.15-15
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic?iency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet?ween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr?ease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$$$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea?ses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin?ear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num?ber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco?very rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• 한국수산과학회지
• /
• 제46권4호
• /
• pp.371-376
• /
• 2013

A feeding trial was conducted to determine the optimum dietary protein and lipid levels for the growth of juvenile muddy loach Misgurnus anguillicaudatus. Eight experimental diets (designated as P20L7, P20L14, P30L7, P30L14, P40L7, P40L14, P50L7 and P50L14) were formulated to contain 20%, 30%, 40% and 50% protein with 7% and 14% lipid. Three replicate groups of muddy loach (1.5 g/fish) were fed one of the experimental diets ad libitum for 8 weeks. Survival of fish fed the P20L14 diet was lower than in other groups (P<0.05). Specific growth rate (SGR) and feed efficiency (FE) of fish were affected by dietary protein (P<0.05) and lipid (P<0.005) levels. SGR and FE of fish tended to decrease with increasing dietary lipid level at the same protein level. There were no significant differences in SGR and FE among fish fed diets containing different protein levels ranging from 30% to 50% with the same lipid level. Whole body moisture and lipid contents were affected by dietary protein and lipid levels. Crude lipid content of fish fed the 14% lipid diets was higher than that of fish fed 7% lipid diets at each protein level. The results of this study indicate that a diet containing 30% protein with 7% lipid would be suitable for the optimum growth and effective feed utilization of juvenile muddy loach.

• 한국수소및신에너지학회논문집
• /
• 제18권1호
• /
• pp.12-25
• /
• 2007

Numerical simulation of the natural gas steam reforming process for on-site hydrogen production in a $H_2$ fueling station was conducted on the basis of process material and heat balances. The effects of reforming parameters on the process efficiency of hydrogen production were investigated, and set-point values of each of the parameters to minimize the sizes of unit process equipments and to secure a stable operability of the reforming process were suggested. S/C ratio of the reforming reactants was found to be a crucial parameter in the reforming process mostly governing both the hydrogen production efficiency and the stable operability of the process. The operation of the process was regarded to be stable if the feed water(WR) as a reforming reactant could evaporate completely to dry steam through HRSG. The optimum S/C ratio was 3.0 where the process efficiency of hydrogen production was maximized and the stable operability of the process was secured. The optimum feed rates of natural gas(NGR) and WR as reforming reactants and natural gas(NGB) as a burner fuel were also determined for the hydrogen production rate of $27\;Nm^3/h$.

• 한국수산과학회지
• /
• 제46권6호
• /
• pp.753-760
• /
• 2013

Two feeding trials were conducted to investigate the effects of feeding rate and frequency on growth performance and body composition of juvenile Korean rockfish Sebastes schlegeli reared at $15.0{\pm}0.3^{\circ}C$. In the first trial, three replicate fish groups averaging $2.07{\pm}0.03g$ were fed a commercial diet with one of seven different daily feeding rates: 1.00%, 2.00%, 2.50%, 2.75%, 3.00%, 3.25%, and satiation (3.34%) based on body weight (BW). After four weeks of feeding, fish fed the 3% diet showed significantly higher weight gain (WG) and feed efficiency (FE) than fish that received the other feeding rates. In the second trial, the optimum feeding frequency was evaluated with three replicate fish groups averaging $2.04{\pm}0.03g$. Fish were fed a commercial diet at 2.87% BW with six different daily feeding frequencies: 2, 3, 4, 5, 7, or 9 meals. After four weeks of feeding, WG, specific growth rate, FE, and protein efficiency rate in fish fed 3 meals $d^{-1}$ were significantly higher than those of fish fed 7 or 9 meals $d^{-1}$. In both feeding trials, proximate composition of the entire body changed depending on the feeding rate or frequency. A broken-line regression analysis based on weight gain suggested that the optimum daily feeding rate and frequency for juvenile Korean rockfish at $15^{\circ}C$ was 2.9% BW $d^{-1}$ and 2-3 meals $d^{-1}$, respectively.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.201-201
• /
• 2010

The evaporative desalination system with solar energy would be the efficient and attractive method to get fresh water. This study was described the development of Multi Effect Distillation(MED) with solar energy desalination system. The system was designed and manufactured Multi effect distillation on the capacity of $3m^3$/day. The experimental apparatus consists mainly of ejector pump, Hot water pump, flow meter, demister, cooler, evaporator and condenser. Evaporator and condenser were made Shell&Tube Heat Exchanger type with corrugated tube. The experimental variables were chosen $75^{\circ}C$ for hot water inlet temperature, 40, 60 and $80{\ell}$/min for hot water inlet volume flow rate, 6.0 and $8.0{\ell}$/min for evaporator feed seawater flow rate, $18^{\circ}C$ for sea water inlet temperature to cover the average sea water temperature and the salinity of sea water is measured about 33,000 PPM (parts per million). for a year in Korea. This study was analyzed the results of thermal performance of Multi Effect Distillation. The results are as follows, The experimental Multi effect distillation is required about 40 kW heat source for production of $3m^3$/day fresh water. Various operating flow rate was confirm in the experiments to get the optimum design data and the results showed that the optimum total flow was $8.0{\ell}$/min. Comparison of Single Effect Distillation with Multi Effect Distillation showed MED is at least more than double of SED.

• 한국작물학회지
• /
• 제36권6호
• /
• pp.513-520
• /
• 1991

충남 예산에서 호밀을 답리작으로 재배할때 파종량과 예취기간가 수량 및 사료가치에 미치는 영향을 요약하면 다음과 같다. 1. 파종량이 많아질수록 호밀의 초장과 단위면 적당 경수는 증가하였으며 건물률은 감소하였다. 2. 청예 및 건물수량은 파종량이 많을수록 높았으며 예산에서 청예수량이 가장 높았던 예취기는 5월 15일, 건물수량이 가장 높았던 예취기는 5월 25일 이었다. 3. 파종량이 많을 수록 그리고 예취시기가 늦을수록조단백질, 가급태단백질 및 가소화단백질 함량은 감소하였으며, 반면에 조섬유함량(ADF와 NDF)은 증가하였다. 4. 파종량이 많을 수록 그리고 예취시기가 늦을수록 총가소화영양분(TDN) 함량과 상대적 사료가치는 감소하였다. TDN 수량은 파종량 18-28kg/10a, 5월 15-25일 수확시 가장 높았다. 5. 호밀의 에너지 함량은 파종량이 많을수록 그리고 예취시기가 늦을수록 감소하나, 단위면적당 에너지 생산량은 ENE와 NEL은 23kg/10a 파종-5월 15일 수확할때, NEM은 18kg/10a 파종-5월 15일 수확할때 가장 높았다. NEG는 18-28kg/10a 파종-5월 5일 수확할 때 가장 높았다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제13권1호
• /
• pp.115-125
• /
• 2000

In recent years a great deal of information has accumulated for livestock on vitamin. function, metabolism and supplemental needs. The role of the antioxidant "vitamins" (carotenoids, vitamin E and vitamin C) in immunity and health of livestock has been a fruitful area of research. These nutrients play important roles in animal health by inactivating harmful free radicals produced through normal cellular activity and from various stressors. Both in vitro and in vivo studies showed that these antioxidant vitamins generally enhance different aspects of cellular and noncellular immunity. A compromised immune system will result in reduced animal production efficiency through increased susceptibility to diseases, thereby leading to increased animal morbidity and mortality. Vitamin E has been shown to increase performance of feedlot cattle and to increase immune response for ruminant health, including being beneficial for mastitis control. Vitamin E given to finishing cattle at higher than National Research Council (NRC) requirements dramatically maintained the red color (oxymyoglobin) compared with the oxidized metmyoglobin of beef. Under commercial livestock and poultry production conditions, vitamin allowances higher than NRC requirements may be needed to allow optimum performance. Generally, the optimum vitamin supplementation level is the quantity that achieves the best growth rate, feed utilization, health (including immune competency), and provides adequate body reserves.