• 한국결정성장학회지
• /
• 제7권3호
• /
• pp.406-417
• /
• 1997

초크랄스키법들 의한 8인치 실리콘 단결정 성장계에 대칭과 비대칭 커스프 자장을 인가하여 결정을 성장시켰을 때 축방향으로 일정한 산소농도분포를 가질 수 있는 적절한 인가 자장의 크기와 비대칭도에 대한 수치해석적 연구를 수행하였다. 결정이 성장할 때 커스프 자장의 형태가 유지되는 방법으로 도가니의 위치를 변화시키는 방법과 인가코일의 위치를 변화시키는 방법을 비교하였다. 대칭 커스프 자장이 인가된 경우, 축방향으로 일정한 산소농도를 얻을 수 있는 자장의 강도변화는 결정이 성장함에 따라 아래로 볼록한 형태를 띠었다. 축밟향으로 일정한 산소농도분포를 갖기 위해 도가니의 위치를 변화시키는 방법과 코일의 위치를 변화시키는 방법을 비교한 결과 비슷한 산소농도의 표준편차값을 가짐을 알 수 있었다. 비대칭 자장이 인가된 경우, 축방향으로 일정한 산소농도 분포를 얻기 위해서는 비대칭도는 결정이 성장함에 따라 점차 증가하는 양상을 보였다.

• 한국환경보건학회지
• /
• 제23권3호
• /
• pp.1-6
• /
• 1997

This research was conducted in the laboratory to investigate an alternative of Copper(Cu) removal from an heavymetal wastewater using the electrochemical precipitation(ECP) process. The ECP unit consisted of an electrolytic cell made of Titanium plate and Steel plate representing anode and cathode. The DC power source applied to the ECP unit had electrical potential(E) of 50$\pm$ 1V, respectively. The synthetic wastewater used in the experiments contained Cu in the 10 mg/l concentration and the electrode separation were 2, 3, 4 cm and the initial pH were 3, 6, 9, 12, and electrolytic concentration were 0.005, 0.0125, 0.025, 0.0375 mole, and the real heavymetal wastewater used in the experiments. From the experiment for removal efficiency according to pH variation, the low pH area doesn't give the coagulation effect by Ti(OH)$_4$ because process interfere with the coagulation and oxidation reaction, therefore the optimum pH was 4-7. The removal rate was 97.75% after the lapse of 30 minutes when copper concentration and electrolytic concentration were respectively 10 mg/l and 0.025 mole. The removal rate was 96.41% after the lapse of 30minutes when the real heavymetal wastewater used. The optimum consumption of power showed 27KWh/m$^3$ when copper concentration, electrolyte concentration and cell potential were respectively 10 mg/l, 0.025 mole and 50$\pm$ 1 Volt.

• KSBB Journal
• /
• 제23권2호
• /
• pp.169-176
• /
• 2008

The concentration of fresh gel from Aloe vera L. by using ulfrafiltration (UF) process was investigated and analyzed. The two membranes (organic and ceramic) with different molecular weight cut-off (MWCO) and modules (flat sheet and tubular) was used. Under optimum operation conditions, ceramic (zirconium dioxide) tubular membrane with MWCO of 50 kDa resulted in higher flux, less fouling, more turbid, higher total solid, higher polysaccharide and less aloin content. Optimum operation conditions were transmembrane pressure of 1.0 bar, feed velocity of 240 L/hr and temperature of $23^{\circ}C$. Volume concentration factor of aloe gel was 3.13 at permeate flux of $51.1\;L/m^2{\cdot}hr$ after processing time of 1.66 hr. Aloin in fresh aloe gel by UF process was effectively removed as permeate and bioactive polysaccharide content was 2.1 times higher than that of fresh aloe gel. These results allowed a very good level of concentration degree and polysaccharide content. Thus, ultrafiltration process of this study was suitable for the concentration of fresh aloe gel though the aloe concentrate showed both the viscosity decrease and partially separation of liquid layer during storage at $4^{\circ}C$.

• 한국염색가공학회지
• /
• 제18권5호
• /
• pp.22-29
• /
• 2006

The purpose of this study was to investigate the dyeability and antibacterial activity on wool fabric dyed with cochineal at variable dyeing conditions. Al, Cr, Fe, Cu and Sn were used as mordants and adsorption was compared with different mordanting methods. The optimum dyeing conditions of wool fabrics were dyeing concentration 2.0%(o.w.s), dyeing temperature $60^{\circ}C$, pH 3 and dyeing time 30 minutes. The pre-mordanting method was preferred for Al and Cr, and the post-mordanting one was preferred for Cu, Sn and Fe to achieve better dyeing. The optimum mordanting conditions of wool fabrics dyed with cochineal were mordanting concentration of 1%(o.w.s), mordanting temperature $60^{\circ}C$, and dyeing time 30 minutes. Wool fabrics dyed with cochineal showed a little antibacterial activity, but it was increased by Cu and Sn mordanting. The light fastness and perspiration fastness of wool fabric treated with cochineal were improved by mordanting.

• KSBB Journal
• /
• 제6권4호
• /
• pp.351-361
• /
• 1991

This study is on the investigation of hydrogen production and substrate removal by photosynthetic bacteria. After using of Rhodospillum rubrum KS-301 and IFO 3986, which are photosynthetic bacteria as strains, R. rubrum KS-301 was turned out a better strain. And result of experiment in which glucose and sodium lactate, components of wastewater, were used limiting substrates, showed that the productivity of hydrogen was indifferent with the kind of substrates. In batch experiments using free cells and immobilized whole cells, the decrease in hydrogen productivity was observed in the latter case. From the results of these experiments, specific growth rate of cells, specific utilization rate of glucose, and specific production rate of hydrogen were calculated. And each rate was expressed in the form of Monod equation of which parameters were estimated. Also the optimum condition of hydrogen production for free cells was $30^{\circ}C$, pH 7, and 12,000 Lux, and the optimum immobilized condition was as follows: initial immobilized cell concentration 1.0g/L, sodium alginate concentration 2% and light intensity 12,000 Lux.

• 동아시아식생활학회지
• /
• 제8권1호
• /
• pp.57-65
• /
• 1998

To utilize deteriorated sweet persimmon effectively, response surface methodology(RSM) was used to determine the optimal vinegar fermentation conditions and monitored by a divided two stage fermentation. The optimum conditions for maximum alcohol content were obtained when the first stage (alcohol fermentation) was carried out with an initial sugar concentration of 18.5$^{\circ}$Brix, agitation rate of 140.8 rpm, fermentation time of 127.6 hr. When sugar concentration was 14$^{\circ}$Brix maximum alcohol content(7.1%) was predicted at fermentation conditions of 160 rpm in agitation rate, 140hr in fermentation time. The optimum conditions for maximum acidity were obtaiend when second stage(vinegar fermentation)was carried out 249.5 rpm in agitation rate, 148.8 hr in fermentation time. Predicted values at the optimum conditions were similar to experimental values.

• 한국연초학회지
• /
• 제27권1호
• /
• pp.100-106
• /
• 2005

To obtain the optimum condition for analysis of 10 alkaloids in tobacco leaves, such as nicotine, nornicotine, anatabine, anabasine, myosmine, cotinine, 2,3'-dipyridyl, $\beta-nicotyrine,\;\beta-nornicotyrine\;and\;\beta-formylnornicotin$, 5 types of extraction method were investigated by GC-FID and GC/MS. The optimum condition of alkaloid extraction was achieved by using methanol:dichloromethane(1:3, v/v) after NaOH treatment. The use of mass selective detector (MSD) provided unambiguous nicotine related alkaloid analysis. Alkaloids in various tobacco leaves were extracted with the optimum extraction condition and quantified by GC/MS/SIM mode. Compared with concentrations of alkaloids among the various tobacco leaves, the concentration of alkaloids was generally in the order burley > flue-cured > oriental tobacco. In flue-cured tobacco leaves, the order of concentration of alkaloids was nicotine > anatabine > nornicotine > $\beta-nicotyrine\;>\;\beta-formylnornicotine\; >\;myosmine\;>\;2,3'-dipyridyl\;>\;cotinine\;>\;anabasine\;>\;\beta-nornicotyrine$. However, in the case of burley and oriental tobacco leaves, the concentration of nornicotine was higher than that of anatabine.

• Journal of Electrical Engineering and information Science
• /
• 제2권5호
• /
• pp.108-113
• /
• 1997

In this paper, the optimum condition of (110) Si etching with the potassium hydroxide(KOH) etchant is presented. Although several researches on (110) Si anisotropic etching have been studied, there has been lack of effects of mask quality and etching conditions on the selectivity and the roughness o the etched surface. Three kinds of masks (film, emulsion and E-beam mask) were used in order to verify the effect of etching properties. Anisotropic bulk etching depends on the crystalline orientation and the concentration and temperature of the etchant. In order to investigate the effect of etching conditions on selectivity and the roughness of the etched surface, the concentration of the etchant was varied from 35 to 45 per cent in weight with increments by 5 per cent and the temperature was changed from 70 to 90$^{\circ}C$ with increments by 10$^{\circ}C$. The combination of the temperature of 70$^{\circ}C$ and the concentration of 40wt.% was found to be the optimum etching condition for high selectivity. Etched surfaces show minimum surfaces show minimum surface roughness at a temperature of 80$^{\circ}C$ and a concentation of 40wt.%. Comb structures with various comb widths were fabricated and the lengths of the combs wree measured with several etching time durations. A micro comb structure 525$\mu\textrm{m}$ high was fabricated for MEMS application.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.78.2-78.2
• /
• 2005

• Journal of Mechanical Science and Technology
• /
• 제14권11호
• /
• pp.1179-1186
• /
• 2000