• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.152-152
• /
• 2016

We studied the effect of the silver grid size on graphene transparent conducting films for flexible organic solar cells (OSCs). The silver grid was used an assistant layer of the graphene to reduce the sheet resistance of substrates. Silver grid with various graphene sizes for optimizing transmittance and sheet resistance of substrates were fabricated on polyethylene terephthalate (PET) substrates to form the hybrid films. The optimized grid geometry on the single layer graphene (SLG) was the grid dimension $200{\mu}m{\times}200{\mu}m{\times}50nm{\times}2{\mu}m$ (length ${\times}$ width ${\times}$ height ${\times}$ linewidth), where the sheet resistance was $55.73{\Omega}/square$ with the average transmittance of ~ 92.83 % at 550 nm. The properties of the OSCs fabricated using SLG with optimized silver grids on PET substrates show a short circuit current of $10.9mA/cm^2$, an open circuit voltage of 0.58 V, a fill factor of 60.8 %, and a power conversion efficiency (PCE) of 3.9 %. The PCE was improved about 91% than that of the OSCs using the SLG without the silver grid. These results demonstrate that the optimized grid geometry to the based on the graphene transparent electrodes contribute to improving the performance of OSCs.

• 한국전자파학회논문지
• /
• 제9권4호
• /
• pp.473-482
• /
• 1998

본 논문에서는 유한차분 시간영역법(FDTD)를 이용하여 단일 마이크로스트립 안테나와 기생소자를 갖는 광 대역 마이크로 스트립 안테나의 특성을 해석하고, 최대 대역폭을 갖는 안테나를 설계하였다. 유한차분 시간영역 법에 의한 수치 해석 결과뜰 Fourier 변환하므로 주파수 영역에서의 반사손실, 입력 임피던스, 복사 패턴 동의 특성을 계산하였다. 이 안테나의 구동소자의 폭, 구동소자와 기생 소자 사이의 간격, 기생소자의 폭과 넓이 변화 에 따라 안테나의 입력 임피던스 및 반사손실, 전압 정재파비 둥의 특성이 변하고, 광대역 특성을 가진다. 따라서 서로 다른 소자틀은 다른 주파수에서 공진되고, 이러한 공진이 대역폭올 향상시킨다. 계산 및 측정한 결과, 결합성을 갖는 마이크로스트립 안테나는 단일 마이크로스트립 안테나의 면적에 약 2배 증가한 반면, 대역폭은 단일 마이크로스트립 안테나에 비해 약 4배 이상 개선되었다. 이러한 계산 결과들은 본 실험의 측정치와 비교적 잘 일치하였다.

• 상하수도학회지
• /
• 제26권4호
• /
• pp.503-512
• /
• 2012

In Yongwon channel, its natural flow of seawater is blocked by the construction of Busan New Port including the container berth. The channel was transformed into a narrow and long one, where it is possible that ships are only allowed to pass through the north-side channel of Gyeonmado located at the point of river mouth to Songjeongcheon. In addition, Yongwon channel is approximately 100 m wide on average and 3,600 m long, and has the highest slenderness ratio (length/width = 36). So it is considered that the changes in the terrain characteristics of Yongwon channel is likely to alter the circulation of sea water, thereby changing its water quality. In this study, the bottom sediment were collected from the 48 points of the Yongwon channel and the long-term leaching characteristics were analyzed. Thus, changes in sediment and water quality were analyzed through the sediment release test to investigate the degree of contamination. The sediment release from the inside region was higher than the outer region, which is due to the pollutant that comes form the downtown area. The results of this study can be used to predict the water quality in the future and prepare the economically optimized countermeasures to improve the water quality of Yongwon channel, Busan New Port.

• 한국기계가공학회지
• /
• 제7권2호
• /
• pp.72-77
• /
• 2008

In this study, we propose and develop PDMS-based modular actuators. The microactuator which looks like a small insect uses thermal expansion power of the PDMS (polydimethylsiloxane; $sylgar^{(R)}$ 184 silicone elastomer). The PDMS-based microactuator provides a large displacement due to a high thermal expansion coefficient (approximately 310ppm). The microacruator with 1mm length $350{\mu}m$ width is optimized by using a numerical analysis. The shape of the PDMS actuatoris variously designed. They are placed at several positions to find the optimal position that provides a high transformation ratio. The PDMS-based microactuators are fabricated using a conventional micromaching technique. The fabricated microactuator is heated using a hot-plate. The actuator displacement is measured as a function of temperature from $27^{\circ}C$ to $300^{\circ}C$. The experimental results are compared to the simulation result. When heating temperature up to $300^{\circ}C$ is applied to the PDMS actuator, each V-groove-shaped joint is actuated $30{\mu}$ mat $300^{\circ}C$. Anotherdesign of the microactuator has a maximum displacement of about 656mm.

• 한국군사과학기술학회지
• /
• 제22권4호
• /
• pp.527-535
• /
• 2019

Hanger in a rail-launched missile protrudes in general and causes to increase significant drag force. One method to avoid the significant increase of drag force is to apply fairings on the hanger. In this paper, sloping shaped fairing parameters of height, width, and length are optimized to minimize the drag force under subsonic speed region by examining three configurations of fairings : front-fairing only, rear-faring only, and the both front and rear fairing. We use Latin Hypercube Sampling method to determine the experimental points, and computational fluid dynamics with incompressible RANS solver was applied to acquire the data at sampling points. Then, we construct a meta model by kriging method. We find the best choice among three configurations examined : both front and rear fairing reduce the drag force by 63 % without the constraint of fairing mass, and front fairing reduced the drag force by 52 % with the constraint of hanger mass.

• 한국정보통신학회논문지
• /
• 제17권10호
• /
• pp.2245-2251
• /
• 2013

본 논문에서는 사각형 패치가 종단에 장하된 소형 직렬 급전 다이폴 쌍(series-fed dipole pair; SDP) 안테나를 제안하였다. SDP 안테나의 폭을 줄이기 위해 두 다이폴 소자의 두 팔의 종단과 접지면의 양끝에 사각형 패치가 추가되었다. 사각형 패치의 길이와 폭에 따른 입력 반사계수와 같은 안테나 성능의 변화를 분석하였다. 1.7-2.7 GHz 대역에서 동작하는 최적화된 소형 SDP 안테나를 설계하여 FR4 기판 상에 제작하였다. 제작된 안테나의 폭은 기존의 SDP 안테나와 비교하여 14.3% 줄었다. 제작된 SDP 안테나를 측정한 결과, VSWR이 2 이하인 임피던스 대역폭은 48.7%(1.68-2.76 GHz), 이득은 5.6-6.0 dBi으로 기존 SDP 안테나와 유사하며 전후방비는 0.7-7.4 dB 향상되었다.

• 대한기계학회논문집A
• /
• 제31권10호
• /
• pp.1025-1030
• /
• 2007

Three kinds of metallic sandwich panels with quasi-Kagome truss cores have been analyzed on their mechanical behaviors subjected to bending load. According to the results of previous work on the optimal design, they were designed to have similarly high strength per weight with the identical overall sizes, i.e., the total length, the width, the core height. Differences were in the face sheet thickness and/or the thickness of the metal sheet from which the core was fabricated through expanding and bending processes. Under the bending load, they performed well as designed, as far as the maximum load is concerned. However, after the maximum load, the load-displacement curves were different each other depending on the slenderness ratio of the truss elements composing the quasi-Kagome truss cores and the face sheet thickness. Namely, the slenderness ratio and the face sheet thickness governed stability of the elastic and plastic buckling. Therefore, if energy absorption characteristics or structural stability as well as the maximum load capacity are to be achieved, the sandwich panel with thick truss members and thick face sheet should be selected.

• 한국정밀공학회지
• /
• 제32권8호
• /
• pp.735-741
• /
• 2015

Piezoelectric materials are well-utilized for transforming mechanical vibrations into electrical energy that can be stored and used to power a diversity of devices. In this work, these materials have been studied to improve the efficiency of a piezoelectric system, whereby the shape and vibration mode of a piezoelectric module was changed. The basic shape of the piezoelectric module used in this work comprises a width of 10 mm, a length of 30 mm, and a thickness of 0.2 mm. The structural design of the piezoelectric module is optimized using a Taguchi method to increase the corresponding electrical-energy generation. The maximum terminal voltage was defined as a characteristic value to evaluate the optimal design parameters. Through this work, we propose an optimal structure with an eccentric and centric mass; furthermore, the voltage increase of approximately 26% was obtained by comparing a general plate-vibrating piezosystem with an optimal plate-vibrating piezosystem.

• 한국금형공학회:학술대회논문집
• /
• 한국금형공학회 2008년도 하계 학술대회
• /
• pp.35-38
• /
• 2008

A pattern master and a Ni stamper for 50nm class of patterns are fabricated through e-beam lithography and Ni electroforming process. A model pattern set is designed, which is based on unit patterns of 50nm, 100nm, 150nm and 200nm in length and 50nm in width. The e-beam process is optimized to fabricate designed patterns with some parameters including dose, accelerating voltage, focal distance and developing time. For Ni electroforming to fabricate Ni stamper, a seed layer, a conducting layer, is deposited first on the pattern master fabricated by an e-beam lithography process. Ni, Ti/Ni and Cr are first tested to find optimal seed layer process. Currently the best result is obtained when adopting Cr deposited to be 100nm thick with continuous tilting motion of the master substrate during the deposition process.

• Composites Research
• /
• 제13권2호
• /
• pp.40-50
• /
• 2000

종횡비가 다른 적층복합재료에 경사형 구조를 도입하고, 이것이 일방향으로의 하중을 받을 때의 좌굴특성을 최대화하기 위해서 복합재료의 각 층에서의 섬유부피분율과 두께를 변수로 sequential linear programming method를 이용하여 최적화 하였다. 이로부터 좌굴특성을 최대화 할 수 있는 최적구조를 제안하였다. 적층복합재료는 종횡비의 영향이 커서 종횡비가 1보다 작은 경우는 최외각층의 섬유부피분율을 최대화하는 방향으로 최적화가 이루어졌으나 종횡비가 2인 경우는 각층에서의 섬유부피분율과 두께비가 어느 정도 균형을 이루는 형태로 최적화가 이루어 졌다. 경사형 구조는 전통적인 균일구조의 복합재료에 비해서 섬유부피와 복합재료의 무게 절감에 큰 효과를 가지는 것으로 확인되었다.