• Journal of KSNVE
• /
• v.10 no.4
• /
• pp.648-654
• /
• 2000

A procedure to determine the realizable optimal positions of rigid supports is suggested to get a maximum fundamental natural frequency. a measured frequency response function based substructure-coupling technique is used to model the supported structure. The optimization procedure carries out the eigenvalue sensitivity analysis with respect to the stiffness of supports. As a result of such stiffness optimization, the optimal rigid-support positions are shown to be determined by choosing the position of the largest stiffness. The optimally determined support conditions are verified to satisfy the eigenvalue limit theorem. To demonstrate the effectiveness of the proposed method, the optimal support positions of a plate model are investigated. Experimental results indicate that the proposed method can effectively find out the optimal support conditions of the structure just based on the measured frequency response functions without any use of numerical model of the structure.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.3 s.246
• /
• pp.302-309
• /
• 2006

Effective mixing plays a crucial role in microfluidics for biochemical applications. Owing to the small device scale and its entailing the low Reynolds number, the mixing in microchannels proceeds very slowly. In this work, we optimize the configuration of obstacles in the Y-channel mixer in order to attain maximum mixing efficiency. Before the optimum design, mixing characteristics are investigated using unstructured grid CFD method. Then, the analysis method is employed to construct the approximate analysis model to be used in the optimization procedure. The main optimization tool in the present work is sequential quadratic programming method. Using this approximate optimization procedure, we may obtain the optimum layout of obstacles in the Y-channel mixer in an efficient manner, which gives the maximum mixing efficiency.

• Journal of the Korean Operations Research and Management Science Society
• /
• v.37 no.4
• /
• pp.197-209
• /
• 2012

This paper studies an emergency service vehicle location problem, where minimum reliability level pre-specified at each demand point is assured. Several models are suggested depending on the busy fraction, which is the time proportion of unavailability for the ambulances. In this paper a new model on computing the busy fraction is suggested, where it varies depending on the distance between the demand point and ambulances, hence it may respond the more realistic situation. The busy fraction for the ambulance location determined by the optimization model is computed by the simulation, and updated through the iterative procedure. It has been shown that the performances of the solutions obtained by the algorithm suggested for the instances appeared in the literature.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.333-336
• /
• 2002

In many cases, fuzzy modeling has a defect that the design procedure cannot be theoretically justified. To overcome this difficulty, we suggest a new design method for fuzzy model by combining genetic algorithm(GA) and mush set theory. GA, which has the advantages is optimization, and rule base. However, it is some what time consuming, so are introduce rough set theory to the rule reduction procedure. As a result, the decrease of learning time and the considerable rate of rule reduction is achieved without loss of useful information. The preposed algorithm is composed of three stages; First stage is quasi-optimization of fuzzy model using GA(coarse tuning). Next the obtained rule base is reduced by rough set concept(rule reduction). Finally we perform re-optimization of the membership functions by GA(fine tuning). To check the effectiveness of the suggested algorithm, examples for time series prediction are examined.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.12
• /
• pp.1250-1255
• /
• 2008

Design of shape fur visco-elastic vibration isolation elements, which are very cost-effective and so popular in many applications is fi?equently based on experiences, intuitions, or trial and errors. Such traditions in shape design make it difficult for drastic changes or new concepts to come out. In this paper, both topological method and shape optimization method are combined together to find out a most desirable isolator shape efficiently by using two commercial engineering programs, ABAQUS and MATLAB. The procedure is divided into two steps. At the first step, a topology optimization method is employed to find an initial shape, where density of either 0 or 1 for finite elements is used fur physical realizability. At the second step, based on the initial shape, finer tuning of the shape is done by boundary movement method. An illustration of the procedure is presented fur a mount of an air-conditioner compressor system and the effectiveness is discussed.

• Structural Engineering and Mechanics
• /
• v.7 no.3
• /
• pp.241-257
• /
• 1999

This paper presents a procedure to minimize the cost of materials of cable-stayed bridges with composite box girder and concrete tower. Two sets of iterations are included in the proposed procedure. The first set of iteration performs the structural analysis for a cable-stayed bridge. The second set of iteration performs the optimization process. The design is formulated as a general mathematical problem with the cost of the bridge as the objective function and bending forces, shear forces, fatigue stresses, buckling and deflection as constraints. The constraints are developed based on the Canadian National Standard CAN/CSA-S6-88. The finite element method is employed to perform the complicated nonlinear structural analysis of the cable-stayed bridges. The internal penalty function method is used in the optimization process. The limit states design method is used to determine the load capacity of the bridge. A computer program written in FORTRAN 77 is developed and its validity is verified by several practical-sized designs.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.10
• /
• pp.157-165
• /
• 1995

The new formulation of designing the two degree of freedom(TDF) robust controller is proposed using $H_{\infty}$optimization and model matching method. In this formulation the feedback controller and feedforward controller are designed in a single step using $H_{\infty}$optimization procedure. Roughly speaking, the feedback controller is designed to meet robust stability and disturbance rejection specifications, while the feedforward controller is used to improve the robust model matching properties of the closed loop system. The proposed formulation will be illustrated and evaluated on a seeker scan-loop. And the performances of TDF robust controller are compared with those of the $H_{\infty}$ controller designed using Loop Shaping Design Procedure proposed by McFarlane and Glover.lover.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1996.10a
• /
• pp.315-321
• /
• 1996

The structural topology optimization presented in this paper is based on an evolutionary procedure, developed by Xie and Steven, in which the low stressed material of a structure is removed from the structure step-by-step until an optimal design is obtained. By appling this procedure a layout or topology of a structure can be found from a initial block of material. The purpose of this paper is to implement the evolutionary procedure, introduce some novel features and investigate its feasibility by studying a few examples.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.964-966
• /
• 2002

This paper presents a magnet circuit design procedure to reduce mover mass of the moving coil type linear direct motor (LDM). The procedure of optimization is based on the response surface methodology (RSM) and Sequential Quadratic Problem (SQP). This procedure of optimization is verified by the comparison of the result of the initial design between the result of the optimum design.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 1998.11a
• /
• pp.556-567
• /
• 1998

Robust design in industry is an approach to reducing performance variation of quality characteristic value in products and processes. Taguchi has used the signal-to-noise ratio(SN) to achieve the appropriate set of operating conditions where variability around target is low in the Taguchi parameter design. Taguchi has dealt with having constraints on both the mean and variability of a characteristic (the dual response problem) by combining information on both mean and variability into an SN. Many Statisticians criticize the Taguchi techniques of analysis, particularly those based on the SN. In this paper we propose a substantially simpler optimization procedure for robust design to solve the dual response problems without resorting to SN. Two examples illustrate this procedure. in the two different experimental design(product array, combined array) approaches.