• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.828-834
• /
• 2013

In this paper, TMC (Tracker Motion Controller) as one of the many research methods for condensing efficiency improvements can be condensed into efficient solar system configuration to improve the power generation efficiency of the castle with Concentrated solar silicon and photovoltaic systems (CPV)experiments using PV systems. Microprocessor used on the solar system, tracing the development of solar altitude and latitude of each is calculated in real time. Also accept the value from the sensor, motor control and communication with the central control system by calculating the value of the current position of the sun, there is a growing burden on the applicability. Through the way the program is appropriate for solar power systems and sensors hybrid-type algorithm was implemented in the ARM core with built-in TMC, Concentrated CPV system compared to the existing PV systems, through the implementation of the TMC in the country's power generation efficiency compared and analyzed. Sensor method using existing experimental results Concentrated solar power systems to communicate the value of GPS location tracking method hybrid solar horizons in the coordinate system of the sun's azimuth and elevation angles calculated by the program in the calculations of astronomy through experimental resultslook clear day at high solar irradiation were shown to have a large difference. Stopped after a certain period of time, the sun appears in the blind spot of the sensor, the sensor error that can occur from climate change, however, do not have a cloudy and clear day solar radiation sensor does not keep track of the position of the sun, rather than the sensor of excellence could be found. It is expected that research is constantly needed for the system with ongoing research for development of solar cell efficiency increases to reduce the production cost of power generation, high efficiency condensing type according to the change of climate with the optimal development of the ability TMC.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.6
• /
• pp.976-982
• /
• 2007

This study investigated whether supplemental Cu, Fe, Zn, and Mn are needed in a practical diet for pullets. Four hundred and twenty females of an egg-laying strain (1-d-old, Lohmann Brown Layer) were randomly distributed into 4 groups, consisting of 7 replicates of 15 birds each. During the 18-week experimental period, chicks were given three basal diets in sequence, each with single or multiple Mn, Zn and Cu supplementation to improve the mineral balance gradually. In the Control, no Mn, Zn, and Cu were added; in the single Mn supplemented group (sMn) Mn was added to 120, 60, and 60 mg/kg for 1-6, 7-12, and 13-18 weeks of age, respectively; in the multiple Mn and Zn supplemented group (mMnZn), Mn was added to 180, 90, and 90 mg/kg and Zn was added to 120, 105, and 105 mg/kg for 1-6, 7-12, and 13-18 weeks of age, respectively; in the multiple Mn, Zn, Cu supplemented group (mMnZnCu), Mn, Zn, and Cu were added to the same multiple of basal Fe concentration relative to NRC (1994) recommendations. Energy and protein metabolizability were determined by subtracting energy/protein intake by energy/protein excretion (from both feces and urine) and dividing by energy/protein intake. There were no statistically significant differences between groups in terms of feed intake, final body weight or tibia length throughout the experiment. Optimal growth performance was observed in the Control, while adding trace minerals to basal diets tended to result in decreased productive performance. Protein metabolizability was increased by mMnZn and mMnZnCu treatments, but energy metabolizability was not affected. Concentrations of Mn, Zn, Cu in excreta varied greatly related to dietary content, and the retentions of Cu, Fe, Zn and Mn were all increased due to the improvement of mineral balance. Based on these results, it is suggested that the concentrations of Cu, Fe, Zn and Mn in typical basal diets used in this study were adequate for normal growth for pullets from 1 to 18 weeks of age.

• Asian-Australasian Journal of Animal Sciences
• /
• v.20 no.12
• /
• pp.1843-1848
• /
• 2007

Thirty-six 1.5 year-old Inner Mongolian White Cashmere wether goats (body weight $28.14{\pm}1.33$ kg) were used to determine the effects of dietary copper (Cu) concentration on ruminal fermentation, nutrient digestibility and cashmere fibre characteristics. Wethers were fed a basal diet (containing 7.46 mg Cu/kg DM) that was supplemented with either 0 (control), 10, 20 or 30 mg Cu/kg DM. To ensure full consumption, animals were fed restrictedly with 0.75 kg feed (DM) in two equal allotments per day. The results indicated that: (1) supplemental 10 mg Cu/kg DM in the basal diet significantly (p<0.05) decreased ruminal fluid pH value and total VFA concentrations were significantly (p<0.05) increased on all Cu treatment groups. (2) Cu supplementation had no influence on DM intake and digestibility of DM, CP and ADF (p>0.05); however, NDF digestibility of groups supplemented with 10 and 20 mg Cu/kg DM were significantly higher than that of the control group (p<0.05). Apparent absorption and retention of copper were decreased with increasing level of supplementation. (3) 20 mg Cu/kg DM treatment significantly (p<0.05) improved cashmere growth rate, but cashmere diameter was not affected by Cu supplementation (p>0.05). In conclusion, supplementation of cashmere goats with Cu at the rate of 10 to 20 mg/kg DM in the basal diet resulted in some changed rumen fermentation and was beneficial for NDF digestibility, while supplementation of 20 mg Cu/kg DM improved cashmere growth. Collectively, the optimal supplemental Cu level for cashmere goats during the fibre growing period was 20 mg/kg DM (a total dietary Cu level of 27.46 mg/kg DM).

• Archives of Plastic Surgery
• /
• v.34 no.4
• /
• pp.466-470
• /
• 2007

Purpose: Active prevention is an essential component in reducing the development of pressure sores. For the high-risk patient group, following the certified pressure sore screening scale as well as educating the patient and the nurses who care for them can lead to optimal management of these patients. Applying a risk assessment scale along with a prevention strategy can reduce medical costs and length of stays at the hospital. The purpose of this study is to evaluate the efficacy of a new pressure sore risk assessment scale based on the universally recommended Braden scale and our prevention program. Methods: From June to August, 2003, our pressure ulcer risk assessment scale was applied to a total of 1882 patients admitted to the experimental group (intensive care unit, neurosurgery, general surgery, and oncology units). It was based on Braden scale. We analysed sensitivity, specificity, positive and negative predictive value and ROC curve to evaluate its efficacy. Pressure ulcer prevention program was composed of patient's education using protocol and specific nursing care. The incidence of pressure ulcers was also measured during the 3 months period, and those were compared to the control group of 1789 patients from March to May, 2002. Results: 118(6.27%) of the experimental group were high-risk with an incidence of pressure ulcers measuring 4 (0.21%). Sensitivity, specificity, positive and negative predictive value of our scale were 100%, 94%, 4%, 100%, respectively, and AUC(area under the curve) was 0.992. In the control group, the incidence of pressure ulcers was 11(0.61%). Statistical analyses using chisquared tests with a significance level of 5%, the results were such that ${\chi }^2=3.6482$(p=0.0561). The results proved to be statistically significant in borderline. Conclusion: The results from this study proved that pressure sore risk assessment scale based on Braden scale has an excellent efficacy, and shows that our pressure ulcer prevention program is partially effective in reducing pressure ulcer incidence.

• Journal of Korea Water Resources Association
• /
• v.55 no.5
• /
• pp.321-331
• /
• 2022

In this study, we tried to present a method for calculating the amount of regression using a watershed modeling method that can simulate the hydrological mechanism of water balance analysis and agricultural water based on watershed unit. Using the soil water assessment tool (SWAT), a watershed water balance analysis was conducted considering the simulation of paddy fields for the Manbongcheon Standard Basin (97.34 km²), which is a representative agricultural area of the Yeongsan river basin. Before evaluating return flow, the SWAT was calibrated and validated using the daily streamflow observation data at Naju streamflow gauge station (NJ). The coefficient of determination (R²), Nash-Sutcliffe Efficiency (NSE), Root-Mean-Square Error (RMSE) of NJ were 0.73, 0.70, 0.64 mm/day. Based on the calibration results for three years (2015-2017), the quick return flow and the return rate compared to the water supply amount for the irrigation period (April 1 to September 30) were calculated, and the average return flow rate was 53.4%. The proposed method of this study may be used as foundation data to optimal agricultural water supply plan for rational watershed management.

• Journal of Bio-Environment Control
• /
• v.15 no.2
• /
• pp.125-137
• /
• 2006

Pleurotus eryngii is one of the most promising mushrooms produced on the domestic farms. The quality as well as quantity of Eryngii is sensitively affected by micro climate factors such as temperature, relative humidity, $CO_2$ concentration, and light intensity. To safely produce high-quality Eryngii all the yew round, it is required that the environmental factors be carefully controlled by well designed structures equipped with various facilities and control systems. At the commercial mushroom cultivation houses of permanent frame type (A, B), this study was carried out to find out reasonable range of each environmental factor and yield together with economic and safe structures influencing on the optimal productivity of Eryngii. This experiment was conducted for about two-year ken Nov. 2003 to Dec. 2005 in cultivation house. Ambient temperature during the experiment period was not predominantly different from that of a normal year. The capacity of the hot water boiler and the piping systems were not enough. Because the capacity of electric heater and air circulation were not enough, air temperatures in cultivation house before improvement of system were maintained somewhat lower than setting temperature, and maximum air temperature difference between the upper and lower growth stage during a heating time period was about 5.1. But the air temperatures after system improvement were maintained within the limits range of setting temperature without happening stagnant of air. Air temperature distribution was generally distributed uniform. Relative humidity in cultivation house before , improvement was widely ranged about $44{\sim}100%$. But as the relative humidity after improvement was ranged approximately $80{\sim}100%$, it was maintained within the range of relative humidity recommended. And $CO_2$ concentration was maintained about $400{\sim}3,300mg{\cdot}L^{-1}$ range. The illuminance in cultivation house was widely distributed in accordance with position, and it was maintained lower than the recommended illuminance range $100{\sim}200lx$. The acidity of midium was some lower range than the recommend acidity range of pH $5.5{\sim}6.5$. The yield was relatively ununiform. In case of bottle capacity of 1,300cc, the mushroom of the lowest grade was less than 3%. The consumption electric energy was quite different according to the cultivation season. The electric energy consumed during heating season was much more than that of cooling season.

• Journal of Bio-Environment Control
• /
• v.22 no.4
• /
• pp.341-348
• /
• 2013

Maintenance of adequate soil tension or content during the period of crop growth is necessary to support optimum plant growth and yields. A better understanding of soil tension and content for precision irrigation would allow optimal soil water condition to crops and minimize the adverse effects of water stress on crop growth and development. This research reports on a comparison of soil water tension and content variations in differently textured soils over time under drip irrigation using two different water management methods, i.e. pulse time and required water irrigation methods. The pulse time-based irrigation was performed by turning the solenoid valve on and off for preset times to allow the wetting front to disperse in root zone before additional water was applied. The required water estimation method was a new water control logic designed by Rural Development Administration that applies the amount of water required based on a conversion of the measured water tension into water content. The use of the pulse time irrigation method under drip irrigation at a high tension of -20 kPa and high temperatures over $30^{\circ}C$ was not successful at maintaining moisture tensions within an appropriate range of 5 kPa because the preset irrigation times used for water control could not compensate for the change in evapotranspiration during day and night. The response time and pattern of water contents for all of the tested soils measured with capacitance-based sensor probes were faster and more direct than those of water tensions measured with porous and ceramic cup-based tensiometers when water was applied, indicating water content would be a better control variable for automatic irrigation. The required water estimation-based irrigation method provided relatively stable control of moisture tension, even though somewhat lower tension values were obtained as compared to the target tension of -20 kPa, indicating that growers could expect to be effective in controlling low tensions ranging from -10 to -20 kPa with the required water estimation system.

• Journal of Mushroom
• /
• v.20 no.3
• /
• pp.113-118
• /
• 2022

This study was conducted to diversify the cultivation of mushroom items and develop a competitive variety of Hypsizigus marmoreus. We focused on developing Hypsizigus marmoreus with lower bitterness, likable shape, and high yield. We have collected and tested characteristics of genetic resources from domestic and abroad since 2019. Breeding (2019), characterization (2020), productivity test (2021), and farm demonstration test (2021) have been sequentially conducted. We bred the new variety 'Yunseul' with unique traits. The optimal temperature for mycelial and fruit body growth were 22-25℃ and 15-18℃, respectively. It was similar to the control variety (Mangadak-2Ho) in the pileus form (hemispherical shape) and the cultivation period. However, it was thinner and longer than the control variety with the pileus diameter, thickness, stipe diameter, and length being 19.9 mm, 7.0 mm, 9.4 mm, and 86.3 mm, respectively. The effective number of fruit bodies was 47.8 in bottle cultivation, which was more than that of the control variety. The yield was 197.4 g/bottle (1,100 cc), which was 30% higher than the yield of the control variety, 151.9 g/bottle (1,100 cc). The parent and control varieties were also incubated alongside the new variety. The somatic incompatibility line was distinct. The band pattern in the mycelial DNA PCR reaction was different from that of the parent and control varieties, confirming the hybrid species.

• The korean journal of orthodontics
• /
• v.27 no.4 s.63
• /
• pp.559-568
• /
• 1997

For orthodontic tooth movement, optimal orthodontic force should be maintained without periodontal breakdown and alveolar bone should be remodeled physiologically Therefore, To obtain proper occlusion through tooth movement within alveolar bone, we should know the biomechanics of teeth and supporting 4issues. The present study was performed to observe histologic changes of periodontal tissue immediately after application of orthodontic force and during the retention period in growing young adult dogs. In this study, experimental group contained between mandibular left canine and 1st molar and control group contained contralateral teeth of same animal. The .018'x.022' stainless steel closed coil spring(Dentaurum Co.) was ligated on the experimental teeth at initial 200gm-force from mandibular canine to 1st molar The animals(4 to 6 months aged young adult dogs) were sacrificed on 0, 14, 28 days after the finish of appliance activation, and then tissue samples were divided into hematoxylin-eosin(HE) staining section, ground section, alkaline phosphatase(ALP) staining section, and tartrate-resistant acid phosphatase(TRAP) staining section. Thereafter, the preparations were examined under light microscopy The following results were obtained: 1. Immediately after the finish of appliance activation, the periodontal space was increased in tension side, but decreased in pressure side compared to that of control. The hyalinized zone was also observed in the periodontium. 2. After the 14-day retention, peridontal space was decreased in tension side and slightly increased in pressure side compared to that of immediately after the finish of appliance activation. The hyalinized zone was repaired and a few osteoblasts showing slightly new bone formation were seen. Osteoblasts were scarcely observed along the alveolar bone. 3. Aftter the 28-day retention, the periodontal fibers are normally repaired. A lot of TRAP(+) osteoclasts md increased alveolar bone resorption were observed in pressure side, and AP(+) osteoblast and increased new bone formation were observed in tension side.

• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.232-239
• /
• 2016

The objective of this study was to examine the effect of photoperiod and light intensity of RBW LED (red:blue:white = 2:1:1) on the growth of Taraxacum coreanum Nakai in a fully artificial light type plant factory. 3 photoperiods and 4 light intensity were used respectively in a fully artificial light type plant production system. Plants were cultured with three photoperiods and four light intensity regimes (conditions) for 270 and 120 days, respectively, using nutrient film technique (NFT) or aeroponics culture methods. For each photoperiod, the total leaves per plant harvested 8 times in all cultivation period was 224 in the 16/8(day/light) photoperiod that had no significant difference from 220 in the 12/12 photoperiod and the lowest number of leaves was 151 occurred in the 8/16 photoperiod, which means that the longer photoperiod, the more leaves harvest. Total fresh weight of above ground was the high in order of in 16/8 photoperiod as 125g, 12/12 photoperiod as 91g, 8/16 photoperiod as 56g. For each light intensity, the total leaves per plant harvested 4 times in all cultivation period was the great in order of $150{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 123, $200{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 107, $100{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 95, $50{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 56 which was the smallest number of total leaves harvest. Total fresh weight of above ground per plant was the high in order of $150{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 43.6g, $100{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 34.6g, $200{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 32.2g, $50{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ as 18.2g. From these results, it was concluded that photoperiod of 16/8 and light intensity at $150{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ can be used as the light condition of RBW LED (red:blue:white = 2:1:1) for optimal growth of Taraxacum coreanum Nakai in a fully artificial light type plant factory.