• 터널과지하공간
• /
• 제13권3호
• /
• pp.235-243
• /
• 2003

최근 경향은 터널연장이 점점 장대화되고 있음을 보여주고 있으며, 또한 경제적인 이유로 고속도로 터널의 제트팬 종류 환기방식에 대한 적용이 점차 증대되고 있다. 차량엔진의 성능이 향상됨에 따라 최적 환기방식을 결정하는 중요한 요소인 소요환기량(Qreq)은 결과적으로 줄어들고 있다. 소요환기량 특성도(Qreq contour map)는 터널연장, 종단경사 그리고 소요환기량 사이의 관계를 나타내는 그래프이다. 그리고 제트팬 환기방식이 가능한 터널제원을 평가하기 위해서는 소요환기량의 변화를 이해하는 것이 중요하다. 그러므로 본 연구에서는 소요환기량 특성도를 이용하여 제트팬 환기방식의 가능 터널제원을 결정하는 그래프적 분석법에 관한 연구를 대상으로 하고 있다. 또한 국내 고속도로상의 지역별 교통량 구성비에 따른 분석도 연구대상으로 하고 있다.

• 한국항공우주학회지
• /
• 제36권5호
• /
• pp.438-447
• /
• 2008

본 논문에서는 이동최소자승법을 이용한 근사모델을 사용하여 신뢰성 최적설계를 수행하였다. 신뢰성 최적설계의 수행을 위한 반응표면 생성에는 RSM 과 Kriging이 사용될 수 있다. RSM은 계산시간은 빠르나 비선형성이 강한 문제에 약하며 Kriging은 비선형성이 강한 문제에 적용할 수 있으나 계산시간이 오래 걸리는 단점이 있다. 이 두 방법을 보완한 방법인 이동최소자승법(MLSM)을 이용하여 신뢰성 최적설계를 위한 반응표면을 생성하였다. 이동최소자승법을 이용한 신뢰성 최적설계기법은 Rosenbrock function 과 six-hump carmel back function으로 검증하였고 다른 기법과 비교하였다. 이동최소자승법을 이용하여 무인항공기 배기 덕트의 신뢰성 최적설계를 수행하였고 이는 항공우주구조물의 최적설계에 유용할 것으로 보여 진다.

• 한국물환경학회지
• /
• 제26권5호
• /
• pp.754-760
• /
• 2010

This study was carried out not only to evaluate optimal operating condition to increase biogas production, but also to estimate feasibility of renewable energy from anaerobic digester of sewage sludge. Semi- continuous Fed and Mixed Reactors (SCFMRs) were operated in various condition to quantify the reactor variables. The result of SCFMR operation showed that the biogas productivity and total volatile solids (TVS) removal of total solids (TS) 4% reactor at hydraulic retention time (HRT) 20 days with Organic Loading Rate (OLR) of $1.45kg/m^3-d$ were $0.39m^3/m^3-d$ and 26.7%, respectively which was two times higher than that of TS 2.5% reactor. Consequently the daily biogas production of $20,000m^3$ would be possible from the total volume of $52,000m^3$ of anaerobic digesters of the municipal wastewater treatment plant in D city. In feasibility study for the Biogas utilization, combined heat and power system (CHP) and CNG gasification were examined. In case of CHP, the withdrawal period of capital cost for gas-engine (GE) and micro gas-turbine (MGT) were 7.7 years and 9.1 years respectively. biogas utilization as Clean Natural Gas (CNG) shows lower capital cost and higher profit than that of CHP system. CNG gasificaion after biogas purification is likely the best alternative for Biogas utilization which have more economic potential than CHP system. The withdrawal period of capital cost appeared to be 2.3 years.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권8호
• /
• pp.891-898
• /
• 2005

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint race, and energy required lot welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy amount of upset. working time, and residual stresses in the joint. Inertia welding was conducted to make the large exhaust valve spindle for low speed marine diesel engine. superalloy Nimonic 80A for valve head of 540mm and high alloy SNCrW for valve stem of 115mm. Due to different material characteristics such as, thermal conductivity and flow stress. on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and Parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the Predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters. especially for welds for which are very expensive materials or large shaft. Many kinds of tests, including macro and microstructure observation, chemical composition tensile , hardness and fatigue test , are conducted to evaluate the qualify of welded joints. Based on the results of the tests it can be concluded that the inertia welding joints of the superalloy exhaust valve spindle are better properties than the material specification of SNCrW.

• Journal of Advanced Marine Engineering and Technology
• /
• 제13권4호
• /
• pp.63-74
• /
• 1989

디젤기관의 연료분사계는 연소실과 함께 디젤기관의 성능에 가장 큰 영향을 미치는 요소의 하나로 이에 대한 이해는 디젤연소 규명에 있어서 매우 중요하다. 그러나 이분사계는 발화 및 완전연소에 필요한 무화, 공기의 이용율을 증가시키는 관통성 및 분포성등의 요건뿐만 아니라 요구되는 분사율, 2차분사 그리고 분사펌프와의 결합등의 많은 문제와 연관되어 있다. 따라서 본 연구에서는 이와 같이 복잡한 디젤기관의 연료분사계를 단순화시켜서 펌프측, 노즐측 및 분사파이프측의 세부분으로 나누어 모델링하여 해석함으로써 새로운 연료분사계의 개발을 위한 기초연구자료를 구하는 것을 목적으로 하였다. 분사파이프내의 압력과 분사계의 실험을 통하여 본 모델의 타당성을 검토하였으며 각 분사계에 있어서 분사량을 최대로 하는 분사파이프직경이 존재함을 확인할 수 있었다.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.375-382
• /
• 2007

The multi-driver off-road vehicle drive-line consists of many components, with close connections among them. In order to design and analyze the drive-line efficiently, a modular methodology should be taken. The aim of a modular approach to the modeling of complex systems is to support behavior analysis and simulation in an iterative and thus complex engineering process, by using encapsulated submodels of components and of their interfaces. Multi-driver off-road vehicles are comparatively complicated. The driving-line is an important core part to the vehicle, it has a significant contribution to the performance. Multi-driver off-road vehicles have complex driving-lines, so performance is heavily dependent on the driving-line. A typical off-road vehicle's driving-line system consists of a torque converter, transmission, transfer case and driving-axles, which transfers the power generated by the engine and distributes it effectively to the driving wheels according to the road condition. According to its main function, this paper proposes a modularized approach for design and evaluation of the vehicle's driving-line. It can be used to effectively estimate the performance of the driving-line during the concept design stage. Through an appropriate analysis and assessment method, an optimal design can be reached. This method has been applied to practical vehicle design, it can improve the design efficiency and is convenient to assess and validate the performance of a vehicle, especially of multi-driver off-road vehicles.

• 한국자동차공학회논문집
• /
• 제16권1호
• /
• pp.106-113
• /
• 2008

The starter motor noise is usually well identified by the customers since it is operated while the engine is quiet, and leaves distinct impressions of the vehicle. In this study the design of experiments(DOE) was applied to the identification of the noise sources of direct drive starter motor since this process usually requires lengthy analysis and elaborate experiments. In the first stage of the test, five controllable factors(alignment and dynamic unbalance of armature, tightening torques of T/bolt and center bracket bolt, and alignment of the center bracket-yoke-rear bracket), excluding static unbalance, are sorted out of all possible factors. Test results showed that the dynamic unbalance and misalignment of armature are the major factors. However, the error level of the first test was relatively high, indicating that there might be some missing major factors. In the second stage test the results showed that both static and dynamic unbalances are the dominant factors contributing to more than 80% of the overall noise, while the misalignment contributes around 12%. Error of the second test was about 4% that could be considered satisfactory. The noise level of the optimal product was predicted to be reduced by 19dBA, and verification test showed the average noise reduction of 16.8dBA with the standard deviation of 3.2dBA, and proved the usefulness of the whole DOE process.

• 수산해양기술연구
• /
• 제47권4호
• /
• pp.435-442
• /
• 2011

In an attempt to respond to the increase in international oil prices and reduce operating expenses, ship remodeling was carried out on a 740ton class tuna purse seiner. To strengthen the competitiveness of the fisheries industry by improving vessel performance, a bulbous bow was newly equipped. The slipway and rudder area were also lengthened and enlarged with the propeller and main engine remained unchanged. To reduce the hull resistance, a circle type bulbous bow was attached on the hull behind bow thruster and thus the cost for exchanging electrical equipment for bow thruster was reduced. The new rudder area was expanded 15% more than the old one within the extent that the existing mechanical control part and rudder stock were not changed. To prevent fishing net damage and stabilize wake field, slipway was lengthened to the optimal position. All of the new design of remodeling parts went through the model tests in towing tank and CWC. Besides resistance test, all of necessary model test results were delivered for hydrodynamic character for the modified ship. The maneuvering simulation to verify that the remodeled ship satisfies the IMO rules was performed in both zigzag and turning tests. The estimated resistance with new bulbous bow and lengthened stern was reduced by 4.8% in the 2-dimensional analysis and 17.4% in the 3-dimensional analysis in comparison of conventional ship. The average reduction of resistance was estimated about 10%. Maneuvering character of modified hull form was found to satisfy all regulations under IMO. The remodeling of tuna purse seiner can not only improve fishing performance but also contribute to reduction of operating cost by saving energy for the fisheries industry.

• 한국자동차공학회논문집
• /
• 제16권4호
• /
• pp.56-62
• /
• 2008

A synthetic gas reformed from hydrocarbon-based fuels consists of $H_2$, CO and $N_2$. Hydrogen contained in the synthetic gas is a very useful species in chemical processes, due to its wide flammability range and fast burning speed. The ESGI (Exhaust Synthetic Gas Injection) technology is developed to shorten the light-off time of three way catalysts through combustion of the synthetic gas in the exhaust manifold during the cold start period of SI engines. Before the ESGI technology is applied to the test engine, the authors set a test rig that consists of gas temperature and composition controllers, an exhaust pulse generator and an exhaust manifold with a visualization window, in order to optimize the point and conditions of injection of the synthetic gas. Through measuring burned gas temperatures and taking photographs of synthetic gas combustion at the outlet of the exhaust manifold, the authors tried to find the optimal injection point and conditions. Analysis of burned gas composition has been performed for various $O_2$ concentrations. As a result, when the synthetic gas is injected at the port outlet of the cylinder No. 4 and $O_2$ concentration exceeds 4%, combustion of the synthetic gas is strong and effective in the exhaust manifold.

• Journal of Nutrition and Health
• /
• 제35권1호
• /
• pp.115-123
• /
• 2002

This study was carried out to investigate the utilization status of internet dietary information by gender(boys: 363, girls: 366) in adolescent(middle & high school students). The results were summarized as follows. The internet using frequency of 6-7times per week had 45.0% of subjects and the using time of internet per a time was shown mainly'<2hours(68.5%)'. The main place for internet use was home(79.0%) and favorite search engine was 'Yahoo'(45.7%) and 'Daum'(19.3%). As main purpose using internet were mentioned 'social intercourse'(45.0%) and data search'(24.8%). The organization that offer to reliable internet information was educational institution'(49.4%). The problems in using information site were 'poor information'(26.4%), 'slow connection speed'(22.6%), and 'don't arouse interest'(18.8%). The search experience about dietary information had only 27.9% of subjects and search purpose was 'for homework'(33.3%) and 'for health'(32.0). The satisfaction degree of dietary information was not high. The connection motive to dietary information was mainly 'by site navigation casualty'(55.7%). Only 7.7% of subjects had experience of nutrition counseling using internet, and the motive of nutrition counseling was also 'by site navigation causally'(55.8%). The purpose of counseling was 'for diet'(41.5%) and 'for health problem'(30.2%), and the satisfaction degree of counseling result was very low. As the ask of improvement for counseling site were pointed out 'poor in answer content'(44.8%) and 'lazy answer'(31.0%). The subjects wanted to get the dietary information about 'growth in status'(41.4%), 'diet related skin beauty'(14.6%), the update period less 1 month, and the way of 'free board'(32.3%), 'game'(21.1%) and 'animation'(19.3%) as offer tool. The results of this study showed that although the internet using percent and frequency of subjects was high, they used dietary information very seldom and they are dissatisfied with internet nutritional information. Therefore, the information donor should consider which dietary information was needed and what is the optimal tool for adolescent.