• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1526-1531
• /
• 2007

Data transmission capacity that is required in 2010 is forecasted that increase by optical communication capacity more than present centuple, and is doing increased demand of optical communication related industry product present. Specially, Lid glass' application that is one of optical communication parts is used in optical communication parts manufacture of Fiber array, Ferrule array, Fanout Black, Silica optical waveguide chip and splitter etc. Also, it is used widely for communication network system, CATV, ATM-PON, FTTH and system. But, Lid glass need much processing times and becomes cause in rising prices of optical communication parts because production cost is expensive. The objectives, of this work is to suggest the micro concave and convex pattern manufacturing technology on borosilicate plate using high temperature and compression molding method. As a result, could developed micro pattern Mold more than 5 pattern, and reduce Lid Glass manufacture cycle time.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.218-224
• /
• 1999

It is necessary to improve mechanical and optical properties in the optical disk substrates as the information storage devices with high storage density using short wavelength laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates with high is regarded as the most suitable process to manufacture optical disk substrates with high dimensional accuracy low residual stresses and superb optical properties In the present study polycarbonate optical disk substrates were fabricated by injection compression molding and the birefringence regarded as one of the most important optical properties for optical disk is measured. The effects of various processing conditions upon the development of birefringence distribution were examined experimentally. It was found that the value of the birefringence distribution were very sensitive to the mold wall temperature history and the variance of the birefringence distribution in the radial direction was affected by the level of the packing and the compression pressure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.201-204
• /
• 1999

Polarization mode dispersion (PMD) restrict the bend-width of single mode optical filer, and it is important parameter in the optical fiber having long-length. Although fiber has perfect circular symmetry, fiber bending, twisting and laws governing manufacture cause additional Polarization mode dispersion. The effect of polarization mode dispersion in general single mode fiber of long length is discussed in this paper. Measurement of PMD with random mode coupling were conducted in two kind of fibers using different laws governing manufacture and interferometric method.

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.02a
• /
• pp.373-374
• /
• 2006

This paper physically demonstrates that our proposed method improves the Signal-to-Noise Ratio (SNR) of significantly increase the number of acceptable optical signals in PON(Passive Optical Network) systems. This method reduced Optical Beat Interference(OBI) by using CDMA.

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.07a
• /
• pp.539-540
• /
• 2006

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.3
• /
• pp.218-222
• /
• 2011

This paper proposes a single-joint optical torque sensor with one body structure. Conventional optical torque sensors consist of three parts, two plates and an elastic structure. They have slightly slipping problem between plates and elastic structure due to the manufacturing tolerance. Since the order of measurement range of optical sensor is about ten micrometers, the slipping problem causes large measurement error, especially in the case of vibrational or high speed plant. This problem does not occur in the proposed design due to the one body structure. The proposed sensor has advantage of low cost, light weight, and small size. And it is easy to design and manufacture. Simulation works that analysis of stress and strain are performed accurately. To demonstrate the performance of proposed sensor, experiments were implemented to compare with a commercial force/torque sensor (ATI Mini45).

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.217-218
• /
• 2009

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.360-361
• /
• 2004

An atomization doping process is proposed to manufacture nonlinear optical fiber containing higher concentration of PbTe nano-particles in the core of the fiber than that by the conventional solution doping process. The absorption peaks appeared near 725nm, 880nm, and 1050nm are attributed to the PbTe quantum dots in the fiber core.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.11a
• /
• pp.184-185
• /
• 2002

We discussed the main issues of 10GHz Receiver packaging. High frequency structure simulations and circuit simulations for TO-CANs led to a new design for 10GHz optical receiver module packaging. The simulation results were compared to the measured laboratory data. The proposed package has low cost and easy manufacture process far mass production. Using this package, we had a good optical to electrical conversion (OE) characteristic at a data rate of 10Gbps.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1330-1333
• /
• 2006

The channel shape of FFL(Flat Fluorescent Lamp) was designed by optical simulation. It was possible to design and manufacture the channel in any shape using glass forming. The best suitable brightness uniformity of 83.7% was achieved.