• Journal of Korea Multimedia Society
• /
• v.16 no.9
• /
• pp.1067-1076
• /
• 2013

Known as an important criterion that evaluates performance of future high-speed backbone networks, burst data loss ratio is well-studied in Optical Burst Switching networks. Current literatures mostly focus on reduce burst loss ratio without considering the system stability and link utilization after reducing. In this paper, we propose a novel framework which comes from feedback theoretic to dynamically control burst loss ratio in OBS. The proposed scheme tries to track the pre-set values of burst loss ratio and increases the stability and link utilization degree. The simulation results show that measured burst loss ratio always tracks setup reference with small errors, wavelength channel utilization is increased up to 2% and the system stability is also improved.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.6
• /
• pp.841-847
• /
• 1993

The evaluation methods of the splicing loss in attenuation characteristics of optical fiber were measured and analyzed presently, the splicing loss of single mode optical fiber is measured by the cut-back technique and the backscattering technique. Comparing the splicing loss measured by above two technique, evaluation method of splicing loss measured by backscattering technique (OTDR) shall be calculated by the splicing loss is occurred due to difference of the backscattering coefficient in the spliced fibers. Thus. this analysis of the splicing loss is certainly applied in installation of the optical fiber cables for management of the data.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.8
• /
• pp.153-165
• /
• 1995

The design procedure of a GaAs/AlGaAs semiconductor matrix optical switch is presented for a simplified tree architecture in the viewpoint of optical loss. A low loss, 0.537 dB/cm, pin type substrate is designed by considering the loss due to imputity doping at 1.3 $\mu$m wavelength. The operating voltage and the device length of a reversed ${\Delta}{\beta}$ electro-optic directional coupler(EODC) swith which is a cross-point device of the 4${\times}$4 matrix optical switch and the bending loss of rib waveguide are caculated as functions of waveguide parameters and bending parameters. There is an optimum bending radius for some waveguide parameters. It is recommened that higher optical confinement conditions such as wide waveguide width and higher rib-height should be chosen for structural parameters of a low loss and a process insensitive 4${\times}$4 matris optical switch. A 4${\times}$4 optical matrix switch which has a 3 dB loss and a 12 volt operating voltage is designed.

• Journal of the Optical Society of Korea
• /
• v.7 no.2
• /
• pp.79-83
• /
• 2003

In this paper, we describe the fabrication process of a photonic crystal fiber and present the measured optical properties of the photonic crystal fiber. The fabrication of the photonic crystal fiber involves stacking, jacketing, collapsing, and drawing using a conventional drawing tower The photonic crystal fiber drawing needs higher tension to maintain the uniform air hole structure. Thus, the temperature of the photonic crystal fiber drawing is lowered by a few hundred degrees Celsius than for the case of conventional optical fiber drawing. The optical properties of the fabricated photonic crystal fiber such as mode profile, optical loss, transmission spectrum, bending loss, and polarization dependent loss are measured.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.82-88
• /
• 2007

This work is to fabricate a precise optical fiber array using polymer composite for optical interconnection. Optical fiber array has to satisfy low optical loss requirement less than 0.4 dB according to temperature change. For this purpose, design criteria for an optical fiber array was derived. The coefficient of thermal expansion of silica particulate epoxy composites was affected by volume fraction of silica particles. And also, elastic modulus of silica particulate epoxy composites was affected by volume fraction of silica particles. To obtain the coefficients of thermal expansion below $10{\times}10E-6/^{\circ}C$ and elastic modulus more than 20 GPa , we chose the volume fraction more than 76%. Using silica particulate epoxy composites with the volume fraction 76%, 8-channel optical fiber array with dimensional tolerances below $1\;{\mu}m$ was manufactured by transfer molding technique using dies with the uniquely-designed core pin and precisely-machined zirconia ceramic V block. These optical fiber arrays showed optical loss variations within 0.4 dB under thermal cycling test and high temperature test.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.468-472
• /
• 2005

This paper is to investigate the influence of the endface quality on the loss characteristics of a plastic optical fiber connector for in-car network service. Using the parameters of the surface roughness and applied load, insertion loss of connector is measured. Due to scattering and change of refractive index, an optimal condition for low-loss coupling exists. We present the optimal condition as surface roughness $R_{rms}$ = 8 nm and contact load up to 50 N.

• Journal of the Korean Physical Society
• /
• v.73 no.11
• /
• pp.1663-1674
• /
• 2018

We propose the Poynting vector analysis of the air mode in a top-emitting organic light-emitting diode (OLED) by combining the transfer matrix method and dipole source term. The spatial profiles of the time-averaged optical power flow of the air mode are calculated inside and outside the multilayer structure of the OLED with respect to the thickness of the semi-transparent top cathode and capping layer (CPL). We elucidate how the micro-cavity effect controlled by the thickness variation of the semi-transparent top cathode or CPL affects the internal optical power and absorption loss inside the OLED multilayer and the external optical power coupled into the air. When the calculated absorption loss and external power obtained by the proposed Poynting vector and currently-used point dipole models are compared, two calculation results are identical, which demonstrates the validity of the two models.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3277-3285
• /
• 1996

In this paper, w designed an opical power distribution device for application to an optical switching and an optical subscriber loop. We fabricated PSG thin film by LPCVD. Based on the measured index of fabricted thin film, rib-type waveguide was transformed to two-dimension by the effective index method and we simulated dispersion property to find asingle-mode condition. We found that the optimum design parameters of rib-type waveguide are:cladding layer of 3.mu.m, core layer of 3.mu.m, buffer layer of 10.mu.m, and core width of 4.mu.m. Each side of the guiding region was etched down to 4.mu.m to shape the core. We used these optimum parameters of the rib-type waveguide with branching angle of 0.5.deg. and simulted the Y-branch waveguide by the BPM simulation. Numerical loss in branching area was claculated to be 0.1581dB and equal to the total loss of the Y-branch. The loss of the fabricated Y-branch waveguide on PSG film ws 1.6dB at .lambda.=1.3.mu.m before annealing but was 1.2dB after annealing at 1000.deg. C for 10 minutes. Consequently, the loss of branching area from 3000.mu.m to 6000.mu.m in the z-direction was 0.8dB, and single-mode propagation was confirmed by measuring the near field pattern. For coupling the fabricated Y-branch waveguide with an optical fiber, we fabricated V-groove which was used as the upholder of optical fiber. An etching angle was 54.deg. and the width and depth of guiding groove was 150.mu.m, 70.mu.m, respectively. The optical fiber is inserted onto V-groove. Both the Y-branch and V-groove were connected through the index matching oil. Coupling loss after connecting Y-branch and the optical fiber on V-groove was 0.34dB and that after injecting index mateching oil was 0.14dB.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.12
• /
• pp.978-982
• /
• 2010

For mass information transfer, the optical communication using optic fiber has been widely used. Especially, in the field of medical image, the large data is digitalized based on the standard image and it is used for telemedicine with this method. Therefore, to transfer the large amount of data fast and effectively POF (Plastic Optical Fiber) can be used and the development of optic connector for connection between POFs is very important. In this study, for stable optical coupling of POF optic fiber Ferrule and Sleeve were designed and produced by considering the bond stability and the insertion loss according to the physical contact and roughness profile was evaluated. As a result of examining the insertion loss by physical contact method of two optic fibers, it showed the loss was about 1.895dB. According to the results from studying the condition of grinding section for POF mass production, the mass production condition was established as POF profile roughness of 6nm and the loss of 0.2dB or lower by controlling the film size and time step by step.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.10
• /
• pp.64-72
• /
• 1995

In this paper, atmospheric turbulence and absorption under clear weather condition, which affect the optical satellite up-link communication between geo-satellites and earth station, were studied. In case of the up-link communication, the received optical power is weakened by pointing loss caused by beam tilt which is the main effect of turbulent atmosphere. This pointing loss directly has relation to the diameter of optical transmitting antenna. From the inverse proportion of the pointing and spaced loss, it is the regions where the diameter of transmitting antenna increases abruptly and the efficient design of transmitting antenna is impossible. In case of using channel coding, it was shown that the peak value of diameter moved to the lower regions of elevation angle with increasing the coding gain and its width was also decreased. In case of considering both coding gain and transmission rate on the design of transmitting antenna, it was known that more coding gain was necessary as transmission rate was increased.