• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.5
• /
• pp.272-277
• /
• 2006

The present study is devoted to investigate numerically the optical characteristics of multi-layer thin film structures such as $Si/SiO_2\;and\;Ge/Si/SiO_2$ by using the characteristics transmission matrix method. The reflectivity and the absorptivity rate for thin film structures are estimated for different incident angles of rays and various film thicknesses. In addition, the influence of wavelength on optical characteristics related to complex refractive index is examined. It is found that such wave-like characteristics are observed in predicting reflectivities and depends mainly on film thickness. Moreover, the present study predicts the film thickness for ignoring wave interference effects, and it also discusses the fundamental physics behind optical and energy absorption characteristics appearing in multi-layer thin film structures.

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.98-101
• /
• 1991

The As2S3 thin film has a characteristics of optical modulation in both amplitude and phase. Since the As2S3 thin film can be used as a real-time reconfigurable optical filter, the fSDF filter can be optically fabricated on it. According to the modulation characteristics of the As2S3, the optimal fSDF filter recorded on this thin plate has the form of continuous amplitude and binary phase. Computer simulation and optical experiments on the optical pattern classification show that the As2S3 is suitable for the optical fSDF filter.

• Electrical & Electronic Materials
• /
• v.9 no.5
• /
• pp.445-449
• /
• 1996

Structural and optical characteristics in Se thin film fabricated by EBE method had been studied. Se thin film was deposited with noncrystalline until substrate temperature of >$100^{\circ}C$ Color of its surface had red genealogy, and its optical energy band gap was about 2.45 eV. But Se film was grown with monoclinic at substrate temperature of over >$150^{\circ}C$ Also, color of its surface had gray genealogy, and its optical energy band gap was about 2.31 eV. Finally, after heat-treatment at >$150^{\circ}C$ for 15 min with substrate temperature of >$100^{\circ}C$ noncrystalline Se was proved to be hexagonal, and color of its surface had dark gray genealogy, and its optical energy band gap was about 2.06 eV. From the results, it was known that Se thin film for photoelectric device with the lowest optical energy band gap was accepted from hexagonal structure.

• Journal of Sensor Science and Technology
• /
• v.32 no.1
• /
• pp.51-54
• /
• 2023

We investigated a humidity sensor based on a polyimide-coated side-polished optical fiber. The polyimide film absorbed moisture, causing the resonant wavelength of the sensor to shift to a longer wavelength owing to the changes in the optical properties of the film. The experimental results showed that the resonant wavelength of the device shifted by 17-18 nm when relative humidity changed from 30% to 90%.

• Journal of Hydrogen and New Energy
• /
• v.12 no.4
• /
• pp.287-292
• /
• 2001

The optical transmittance change of Pd thin film due to hydrogen absorption and desorption was examined at room temperature. Hydrogen absorption and desorption cycling effects on optical transmittance were measured 6 times in the pressure range between 0 and 640 torr. Optical transmittance of Pd film was increasing with increasing hydrogen pressure. Ratio of optical transmittance to the change of pressure at $\beta$ phase is bigger than that of low hydrogen pressure range.

• Journal of the Semiconductor & Display Technology
• /
• v.19 no.4
• /
• pp.51-58
• /
• 2020

Many types of optical plastic films are essential in optoelectronics display unit fabrication and it is important to develop high precision laser cutting methods of optical films with extremely low level of film surface contamination by fume particles. This study investigates the effects of suction and blowing air motions with air flow misalignment in removing fume particles from laser cut line by employing random particle trajectory simulation and probabilistic particle generation model. The computational results show fume particle dispersion behaviors on optical film under suction and blowing air flow conditions. It is found that suction air flow motion is more advantageous to blowing air motion in reducing film surface contamination outside designated target margin from laser cut line. While air flow misalignment adversely affects particle dispersion in blowing air flows, its effects become much more complicated in suction air flows by showing different particle dispersion patterns around laser cut line. It is required to have more careful air flow alignment in fume particle removal under suction air flow conditions.

• Journal of the Korean Applied Science and Technology
• /
• v.20 no.4
• /
• pp.332-340
• /
• 2003

Crosslinked poly(methyl methacrylate) particles from 2.4 to $8.1{\mu}m$ in diameter were prepared by homogenized suspension polymerization. The effect of polymerization parameters such as homogenizing speed, homogenizing time and stabilizer concentration on the particle size were examined. Optical diffusion films were prepared with the crosslinked poly(methyl methacrylate) particles. The effect of film thickness, particle size, and particle size distribution on transmittance and haze of optical diffusion film was examined. Transmittance of optical diffusion film increased with increasing particle size and decreasing film thickness. Haze increased with increasing film thickness and decreasing particle size. We also found the existence of an optimum ratio for optical performance when the mixture of small particle and large particle was used.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.10
• /
• pp.1370-1376
• /
• 2003

The investigation of liquid fuel film on the cylinder liner is an essential to understand the engine-out hydrocarbon emissions formation in SI engines. In this research, two-dimensional visualization was carried out to investigate the liquid fuel film on the quartz liner in the optical engine. For this, the optical engine with hydraulic system was designed based on the commercial SI engine. The visualization was based on the laser-induced fluorescence with total reflection technique. Using a quartz liner and a special lens, only the liquid fuel film on the liner was visualized. With using this technique, the distribution of the fuel film on the cylinder liner was measured for different engine conditions and injection timing in the optical engine.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.111-118
• /
• 2004

The automatic assembly system of micro optical filter is a key technology in the development of optical modules with high functionality. In order to develop an automatic assembly system of optical fiber and filter, we have firstly developed the system and program capable of characterization of 30${\mu}m$-thick film filters as well as conventional optical filters. Moreover, we have carried out the characterization of optical filter using the developed system and program, and compared experimental results with by conventional handwork. The measurement of optical filters using the present system is faster, more precise and more reliable than those based on the conventional handwork.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.306-311
• /
• 2003

In this paper, we modeled the incident beam in order to analyze and evaluate the optical thin film device for wavelength division multiplexing in optical telecommunication network. As applied ray tracing method to the optical path, we were compared the accuracy of coupling efficiency simulated by two modeling methods. In the results of sinulation, ceil modeling method was preferred to annual modeling method in micro-optic device because of accuracy for coupling efficiency and Gaussian intensity distribution. In the results of optimal simulation for optical device using thin film filter, the distance (d1) between optical fiber and GRIN lens, the distance (d2) between GRIN lens and thin film filter and the coupling efficiency were 0.24 mm, 0.25 mm and -0.11 ㏈ respectively. As d2 was displaced at 0.25 mm and d1 was varied in order to evaluate the optimal value, d1 and maximum coupling efficiency were 0.24 mm and -0.35㏈, respectively. Then the results of experiment were corresponded to that of optimal simulation by cell modeling and it was possible to analyze the performance for optical device using thin film filter by the simulation.