• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.116-120
• /
• 2001

Fiber fracture is one of the dominant failure phenomena to determine total mechanical properties in composites. Fiber fracture locations were measured by optical microscopic method and acoustic emission (AE) as functions of matrix toughness and surface treatment by the electrodeposition (ED), and then two methods were compared. Two AE sensors were attached on the epoxy specimen and fiber fracture signals were detected with elapsed time. The interfacial shear stress (IFSS) was measured using tensile fragmentation test and AE system. In ED-treated case, the number of the fiber fracture measured by an optical method and AE was more than that of the untreated case. The signal number measured by AE were rather smaller than the number of fragments measured by optical method, since some fiber fracture signals were lost while AE detection. However, one-to-one correspondence between the x-position location by AE and real break positions by optical method was generally established well. The fiber break source location using AE can be a valuable method to measure IFSS for semi- or nontransparent matrix composites nondestructively (NDT).

• 한국전기전자재료학회논문지
• /
• 제26권7호
• /
• pp.567-574
• /
• 2013

An optical model is proposed in the white LED using phosphor and LED chip. In this paper a new model that describes the absorption rate and quantum efficiency with increasing the mixing ratio of phosphor in silicone, and the allotment of the phosphor absorption optical power in the several phosphor mixing in the silicone. Single phosphor in silicone from the optical measurement data before and after molding, the solution to get the blue optical power and the phosphor emission optical power is proposed. By these solution the absorption rate and the quantum efficiency was obtained. The model with single phosphor mixing in the silicone the validity was confirmed.

• ETRI Journal
• /
• 제23권3호
• /
• pp.97-105
• /
• 2001

$1.6\;{\mu}m$ emission originated from $Pr^{3+}:\;(^3F_3,\;^3F_4)\;{\longrightarrow}\;^3H_4$ transition in $Pr^{3+}-\;and\;Pr^{3+}/Er^{3+}$-doped selenide glasses was investigated under an optical pump of a conventional 1480 nm laser diode. The measured peak wavelength and fullwidth at half-maximum of the fluorescent emission are ~1650nm and 120nm, respectively. A moderate lifetime of the thermally coupled upper manifolds of ${\sim}212{\pm}10{\mu}s$ together with a high stimulated emission cross-section of ${\sim}(3{\pm}1){\times}10^{-20}\;cm^2$ promises to be useful for $1.6{\mu}m$ band fiber-optic amplifiers that can be pumped with an existing high-power 1480 nm laser diode. Codoping $Er^{3+}$ enhances the emission intensity by way of a nonradiative $Er^{3+}:\;^4I_{13/2}\;{\longrightarrow}\;Pr^{3+}:\;(^3F_3,\;^3F_4)$ energy transfer. The Dexter model based on the spectral overlap between donor emission and acceptor absorption describes well the energy transfer from $Er^{3+}$ to $Pr^{3+}$ in these glasses. Also discussed in this paper are major transmission loss mechanisms of a selenide glass optical fiber.

• 한국진공학회지
• /
• 제18권2호
• /
• pp.102-107
• /
• 2009

본 연구에서는 ZnO 박막을 성장하기 위한 plasma-assisted molecular beam epitaxy (PAMBE)에 장착된 플라즈마건에 13.56 MHz의 rf 전력을 인가하였을 때 발생되는 산소 플라즈마의 발광 스펙트럼을 광발광 분광기(optical emission spectroscopy: OES)를 이용하여 조사하였다. 실험은 산소 가스 유량을 1 sccm에서 20 sccm, rf 전력을 25W에서 250 W 범위에서 플라즈마건의 오리피스의 직경을 각각 3 mm 와 5 mm로 달리하여 행해졌다. 산소 플라즈마를 발생시켰을 때 오리피스의 직경에 상관없이 전형적인 산소 플라즈마의 발광 스펙트럼이 관측되었다. 특히 776.8 nm와 843.9 nm에서 $3p^{5}P-3s^{5}S^{0}$, $3p^{3}P-3s^{3}S^{0}$ 천이에 기인하는 강한 산소 원자 발광선이 관측되었다. 산소 유량과 rf 파워가 증가함에 따라 776.8 nm와 843.9 nm의 발광 세기는 증가하였고, 776.8 nm의 스펙트럼 발광 세기의 증가율이 843.9 nm의 스펙트럼 발광 세기 증가율보다 컸다. 또한 오리피스 직경이 3 mm일 때가 5 mm일 때보다 산소 플라즈마가 더 안정적으로 발생하였다.

• 천문학논총
• /
• 제15권spc1호
• /
• pp.61-71
• /
• 2000

The emission line objects such as planetary nebulae, symbiotics, gaseous nebulae, HII regions, novae, supernovae, SNRs, nearby spiral galaxies, dIrr, dE, and nearby active galactic nuclei, would be goldmines for us to dig with the 1.8m bohyunsan optical (BOAO) telescope. We discussed the importance of strategically important diagnostic lines and atomic constant calculation for a study of Galactic and extragalactic emission objects. The scientific background on a spectrometer development history is briefly presented and spectroscopic research areas other than the emission objects are also summarized.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1422-1424
• /
• 2007

A simulation method has been purposed in this paper to optimize the stack structure of metal/ITO cathode for full transparent or top emission devices. The result demonstrates that the complexity of the two proper layers thicknesses design is reduced. Finally, the experiment data also strain the simulation result.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.370-375
• /
• 2003

Optical fiber vibrations sensors (OFVSs) and extrinsic Fabry-Perot interferometer (EFPI) were used in damage monitoring of fiber-metal laminates(FML). The optical fiber vibration sensor and EFPI were applied in order to detect and evaluate the strain, damage and failure of FML. Damages in composites, such as matrix cracks, delamination and fiber breakage may occur as a result of excessive load, fatigue and low-velocity impacts. Tensile and indentation test was performed with the measurement of optical signal and acoustic emission (AE). The signals of the optical fiber vibration sensor due to damages were quantitatively evaluated by wavelet transform. It was found that damage information of comparable in quality to acoustic emission data could be obtained from the optical fiber vibration sensor signals.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2003년도 춘계학술발표대회 논문집
• /
• pp.42-45
• /
• 2003

Optical fiber vibrations sensors (OFVSs) and extrinsic Fabry-Perot interferometer (EFPI) were used in damage monitoring of fiber-metal laminates(FML). The optical fiber vibration sensor and EFPI were applied in order to detect and evaluate the strain, damage and failure of FML. Damages in composites, such as matrix cracks, delamination and fiber breakage may occur as a result of excessive load, fatigue and low-velocity impacts. Indentation test was performed with the measurement of optical signal and acoustic emission (AE). The signals of the optical fiber vibration sensor due to damages were quantitatively evaluated by wavelet transform. It was found that damage information of comparable in quality to acoustic emission data could be obtained from the optical fiber vibration sensor signals.

• Journal of the Optical Society of Korea
• /
• 제14권1호
• /
• pp.49-54
• /
• 2010

In this study, the use of a continuous-wave (CW) supercontinuum (SC) seeded by an erbium-doped fiber's amplified spontaneous emission (ASE) for optical-coherence tomography imaging is experimentally demonstrated. It was shown, by taking an in-depth image of a human tooth sample, that due to the smooth, flat spectrum and long-term stability of the proposed CW SC, it can be readily applied to the spectral-domain optical-coherence tomography system. The relative-intensity noise level and spectral bandwidth of the CW SC are also experimentally analyzed as a function of the ASE beam power.

• 한국자동차공학회논문집
• /
• 제3권2호
• /
• pp.146-156
• /
• 1995

Growing international concern about environmental issues in recent years has led to new proposals for strengthening exhaust emission standards and fuel economy requirements throughout the world. The low emission vehicle(LEV) standards drawn up by the California Air Resources Board(CARB) in the U.S.A are noticeably stringent To cope with this regulation, a reduction of HC emission is the most important challenge for the automotive industry because HC emission levels are severer than any other components emission levels. In this paper, the apparatus for visulalizing the wall film flow in a intake manifold and the spark plug with optical fiber for detecting the signal from diffusion flame are developed to mal,e the HC formation mechanism clear. High speed camera system is also used to elucidate the correlation wall film flow and the diffusion flame. Using these methods, the effect of fuel injection systems such as injection direction, spray angle, atomised injection on HC emission levels is investigated. Consequently, the optimal fuel injection conditions for minimizing the wall film flow and reducing the HC emission are found through this research.