• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.397.1-397
• /
• 2002

For high density optical storage, there should be a high NA objective lens and a shorter wavelength laser diode. To secure the disc tilt margin related to the coma aberration, moreover, it's difficult to apply the tilt compensation mechanism into the portable PC. In this paper, we proposed the 3-axis asymmetry pickup actuator with high efficiency symmetric magnetic circuit, which consisted of the top cover type inner yoke for high magnetic flux density, the coil stack unit for the 3-axis independent operation and vertically polarized magnets. (omitted)

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.356-361
• /
• 2004

A moving-magnet type pickup actuator has an assembly error . That is, the actuating part of an actuator is shifted from initial position after we assemble it into yoke. This is the result of an effect of magnetic force between magnet and yoke. We performed magnetic-analysis using FEA. As a result of simulation, we improved the assembl ing efficiency for moving-magnet type actuator.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.378-380
• /
• 2002

There has been lower the tilt margin by the increase of coma aberration due to the reduction of wave-length and the increase of numerical aperture for high density recording. The RF signal degradation is increased as the decrease of tilt margin. To compensate the tilt margin, the optical pick-up actuator for high-speed CD/DVD re-writable system should be able to drive the radial-tilt motion. We announce that the 3-axis drive actuator for high-speed CD/DVD rewritable system. And what was more, the DC/AC sensitivities of this actuator are suitable fur the low-speed playability, the high-speed readability and the high-speed rewritability.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.12
• /
• pp.24-30
• /
• 2010

The super-resolution near-field structure (super-RENS) disc system is the most promising one for next-generation optical data storage systems to succeed the Blu-ray disc (BD). In this paper, we apply the simplicial canonical piecewise-linear (SCPWL) model to modeling super-RENS read-out signals since reliable and accurate channel modeling is essential for performance analysis and development of equalizers for super-RENS systems. The validity of this model is verified using radio frequency (RF) signal samples obtained from a super-RENS disc, The experiment results on modeling indicate that the SCPWL model can be efficiently utilized for the nonlinear modeling of the super-RENS systems.

• Proceedings of the Optical Society of Korea Conference
• /
• 2004.02a
• /
• pp.248-251
• /
• 2004

근접장 초해상 기술 중 대표적인 Super-RENS (Super Resolution Near Field Structure) 기술을 이용하여 25GB 용량의 BD(Blu-ray Disc) 다음 세대로 예상되는 100 ${\sim}$ 200 GB 용량의 Media 및 기록 재생 기기를 개발하고자 한다. 현재까지 이 기술의 어려움이었던 Stability 특성은 10만회 재생 내구성을 확인하엿고 CNR (신호 대 잡음 비) 특성은 50 nm 미세 마크에 대하여 40 dB의 특성을 확보 하였다. 이 특성은 대략 75 GB에 대응하는 것으로 BD System을 그대로 사용하면서 달성한 세계 최고의 기록 밀도로 평가된다. 향후 과제는 Jitter. Error Rate등 실제 신호 특성의 확보로서, 이의 확보를 통하여 기술의 상품화 가능성이 확인될 것이다.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.5
• /
• pp.578-583
• /
• 2014

Optical pick-up is a core component for data read/write operations in optical disc drives, and an optical pick-up performance evaluator is an instrument used to analyze the overall performance of an optical pick-up. Due to inevitable errors in an analog measurement circuit, resultant evaluation data is not guaranteed to be accurate. In this paper, a calibration method for an optical pick-up performance evaluator is proposed to ensure evaluation accuracy. Measured data is corrected by a 1st order correction function, and a calibration process based on least-square method is utilized to obtain correction coefficients of the correction function. The proposed calibration method is applied to experiments, and enhanced accuracy is presented with resultant evaluation data.

• The Korean Journal of Ceramics
• /
• v.2 no.4
• /
• pp.197-202
• /
• 1996

The highly oriented diamond particles were deposited on the mirror-polished (100) silicon substrates in the bell-jar type microwave plasma deposition system using a three-step process consisting if carburization, bias-enhanced nucleation and growth. By adjusting the geometry of the substrate and substrate holder, very dense disc-shaped plasma was formed over the substrate when the bias voltage was below -200V. Almsot perfectly oriented diamond films were obtained only in this dense disc-shaped plasma. From the results of the optical emission spectra of the dense disc-shaped plasma, it was found that the concentrations of atomic hydrogen and hydrocarbon radical were increased with negative bias voltage. It was also found that the highly oriented diamonds were deposited in the region, where the intensity ratios of carbonaceous species to atomic hydrogen are saturated.

• Journal of Biosystems Engineering
• /
• v.34 no.2
• /
• pp.95-105
• /
• 2009

A method was proposed which employed control of the drop location of fertilizer particles on a spinner disc to optimize the spread pattern uniformity. The system contained an optical sensor as a feedback mechanism, which measured discharge velocity and location, as well as particle diameters to predict a spread pattern of a single disc. Simulations showed that the feed gate adaptation algorithm produced high quality patterns for any given application rate in the dual disc spreader. The performance of the feed gate control method was assessed using data collected from a Sulky spinner disc spreader. The results showed that it was always possible to find a spread pattern with an acceptable CV lower than 15%, even though the spread pattern was obtained from a rudimentary flat disc with straight radial vanes. A mathematical optimization method was used to find the initial parameter settings for a specially designed experimental spreading arrangement, which included the feed gate control system, for a given flow rate and swath width. Several experiments were carried out to investigate the relationship between the gate opening and flow rate, disc speed and particle velocity, as well as disc speed and predicted landing location of fertilizer particles. All relationships found were highly linear ($r^2$ > 0.96), which showed that the time-of-flight sensor was well suited as a feedback sensor in the rate and uniformity controlled spreading system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1595-1604
• /
• 2009

An Optical disk driver is used in many electronic products besides the computers. In particular, the demands are recently increased as an optical disk player/recorder in the mobile products such as camcorder, portable player or in the home theater appliances, etc. However, the more the mobility is emphasized, the more the optical disk player is exposed to the disturbance inputs. For reducing the possibility of malfunction of the optical disk, we propose a nonlinear controller using the disturbance detecting algorithm based on the Kalman filter. Actual experiments were executed to verify the performance of the proposed method. The proposed method controls the tracking error signal within ${\pm}0.1{\mu}m$.

• 연구논문집
• /
• s.28
• /
• pp.229-238
• /
• 1998

Materials and parts required for nondestructive testing should be evaluated using with standard block. And it is ruled that standard blocks should be fabricated from same or similar material with test specimen. In order to manufacture and export materials and parts, quality assurance system should be required. In this paper, ultrasonic characteristics of ASTM 4340 steel ultrasonic standard block are investigated for nondestructive evaluation of udimet 720Li disc. Microstructures of udimet 720Li alloy are investigated using with optical and transmission electron microscope. Also ultrasonic transit time and attenuation are measured from high power ultrasonic analysis system with phase adjustment method. Conclusively, it is proved that 4340 steel ultrasonic standard block can be use for nondestructive evaluation of udimet 720Li disc.