• 한국통신학회논문지
• /
• 제34권2C호
• /
• pp.175-180
• /
• 2009

우수한 에러 정정 부호 기법인 LDPC(Low Density parity Check) 부호를 고밀도 광 기록 시스템에 적용하는 경우, 변조 부호 복호기는 연판정 채널 출력 검출기를 통과해 나온 정보 중에서 패리티 부분을 받아서 연판정 값을 출력해줘야 하는 알고리즘이 필요하다. 따라서 본 논문에서는 고밀도 광기록 채널에서 17PP 변조 부호에 대한 효과적인 연판정 입력 연판정 출력 런-길이 제한 부호의 복호 알고리즘을 제안하고, 이 때 LDPC 부호의 성능을 비교하였다. 그 결과 기존에 연구되었던 (1, 7) RLL을 이용한 연판정 입력 연판정 출력 복호 알고리즘 보다, 고밀도 광 기록 채널에서는, 제안한 17PP를 이용한 연판정 입력 연판정 출력 복호 알고리즘이 0.8dB 정도의 성능 이득이 있는 것을 알 수 있었다.

• 열처리공학회지
• /
• 제8권3호
• /
• pp.169-181
• /
• 1995

This study has been performed to investigate some effects of the power density and traverse speed of laser beam on the optical microstructure, hardness and fatigue resistance of gray cast iron treated by laser surface hardening technique. Optical micrograph has shown that the dissolution of graphite flakes and the coarsening of lath martensite tend to increase with a small amount of retained austenite as the power density increases under the condition of a given traverse speed. Hardness measurements have revealed that as the power density increases, hardness values of outermost surface layer increases from Hv=620 to Hv=647 in case of traverse speed of 2.0m/min at gray cast iron. Fatigue test has exhibited that the fatigue strength of laser surface hardened specimen is superier compared to that of untreated specimen, showing that values for the fatigue strength at $N_f=10^7$ of gray cast iron laser-surface-hardened at a low power density of $4076w/cm^2$ and a high power density of $8153w/cm^2$ under the condition of a given traverse speed of 2.0m/min are $15kg_f/mm^2$ and $20kg_f/mm^2$, respectively, whereas the fatigue strength of untreated specimen is $11kg_f/mm^2$. Under high stress-low cycle condition a noraml brittleness fracture appears, whereas a ductile fracture with beach mark is observed in the specimen tested under low stress-high cycle condition.

• 한국통신학회논문지
• /
• 제31권11C호
• /
• pp.1052-1057
• /
• 2006

본 논문에서는 고밀도 광기록 장치에서 발생하는 디스크 기울임 현상으로 인한 검출 성능 저하를 방지하기 위해서 디스크 기울임 분석기를 갖는 적응 등화 PRML 검출 방법을 VerilogHDL을 이용하여 구현하였다. 디스크 기울임의 분석을 위하여 고정된 패턴으로 일정한 간격마다 반복되는 동기 데이터를 이용하여 분석된 디스크의 기울임 정도를 측정하여 ROM에 저장된 등화기 계수값과 가지 메트릭의 기준값을 갱신한다. 이러한 방법은 지속적으로 계수값을 계산하여 갱신시켜줘야 하는 기존의 적응등화 방법에 비해 간단하게 각각의 계수값을 갱신시킬 수 있다. Hynix $0.35{\mu}m$ STD cell library로 회로를 합성한 결과 35K 정도의 게이트를 필요로 하고 최대동작속도 140MHz의 성능을 보였다.

• 한국통신학회논문지
• /
• 제31권10C호
• /
• pp.927-932
• /
• 2006

본 논문은 고밀도 광 기록 저장장치에서 오류의 주 원인이 되는 tangential tilt의 문제를 해결하기 위한 개선된 부분응답최대유사도 신호 검출 방법을 제안한다. 틸트의 변화에 따라 등화기 계수와 비터비 디코더의 가지 기준값을 적응적으로 갱신하여 채널의 변화에 잘 적응하도록 하였다. 채널의 변화를 감지하는 요소로 주기적으로 반복되는 데이터의 동기패턴을 이용하여 누적 평균을 취한 후 변화량에 해당되는 등화기 계수값과 비터비 디코더의 가지 기준값을 동시에 갱신한다. 제안된 방법을 적용한 결과 기존의 PRML 검출기에 비해 비트 오류율 10-6에서 최대 4dB이상 성능이 향상되는 것을 확인할 수 있었다.

• Current Optics and Photonics
• /
• 제5권2호
• /
• pp.141-146
• /
• 2021

We have evaluated the suppression effect of atmospheric-turbulence-induced optical scintillation in terrestrial free-space optical (FSO) communication systems using a gain-saturated erbium-doped fiber amplifier (EDFA). The variation of EDFA output signal power has been measured with different amounts of gain saturation and modulation indices of the optical input signal. From the measured results, we have found that the peak-to-peak power variation was decreased drastically below 2 kHz of modulation frequency, in both 3-dB and 6-dB gain compression cases. Then, the power spectral density (PSD) of optical scintillation has been calculated with Butterworth-type transfer function. In the calculation, different levels of atmospheric-turbulence-induced optical scintillation have been taken into account with different values of the Butterworth cut-off frequency. Finally, the suppression effect of optical scintillation has been estimated with the measured frequency response of the EDFA and the calculated PSD of the optical scintillation. From our estimated results, the atmospheric-turbulence-induced optical scintillation could be suppressed efficiently, as long as the EDFA were operated in a deeply gain-saturated region.

• 한국재료학회지
• /
• 제18권3호
• /
• pp.117-122
• /
• 2008

Micro-sized bumps on a multi-layered build-up PCB were fabricated by pulse-reverse copper electroplating. The values of the current density and brightener content for the electroplating were optimized for suitable performance with maximum efficiency. The micro-bumps thus electroplated were characterized using a range of analytical tools that included an optical microscope, a scanning electron microscope, an atomic force microscope and a hydraulic bulge tester. The optical microscope and scanning electron microscope analyses results showed that the uniformity of the electroplating was viable in the current density range of $2-4\;A/dm^2$; however, the uniformity was slightly degraded as the current density increased. To study the effect of the brightener concentration, the concentration was varied from zero to 1.2 ml/L. The optimum concentration for micro-bump electroplating was found to be 0.6 ml/L based on an examination of the electroplating properties, including the roughness, yield strength and grain size.

• 천문학회보
• /
• 제44권1호
• /
• pp.34.2-34.2
• /
• 2019

Several observational results show a tighter pitch angle at wavelengths of optical and near-infrared than those that are associated with star formation, which is in agreement with the prediction of the density wave theory. In my recent numerical studies, the dependence of the shock positions relative to the potential minima is due to the tendency that stronger shocks form farther downstream. This causes a systematic variation of the perpendicular Mach number, with radius and makes the pitch angle of the gaseous arms smaller than that of the stellar arms, which supports the prediction of the density-wave theory, independently. However, some observations still give controversial results which show similar pitch angles at wavelengths, and there is no statistical study comparing observations and numerical models directly. By analyzing optical image of disk galaxies in the Carnegie-Irvine Galaxy Survey (CGS), I measured the physical values of stellar and gaseous arms such as their strength, length, and pitch angles. For direct comparison with numerical results, I analyzed more than 30 additional numerical models with varying the initial parameters in model galaxies. In this talk, I will present results both of observational and numerical samples and discuss the physical properties of spiral structures based on the density-wave theory.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.2050-2057
• /
• 1999

It is necessary to improve mechanical and optical properties in the optical disk substrates as the information storage devices with high storage density using short wavelength laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates with high dimensional accuracy, low residual stresses, and superb optical properties. In the present study, polycarbonate optical disk substrates were fabricated by injection compression molding and the birefringence, regarded as one of the most important optical properties for optical disk, is measured. The effects of various processing conditions upon the development of birefringence distribution were examined experimentally. It was found that the values of the birefringence distribution were very sensitive to the mold wall temperature history and the variance of the birefringence distribution in the radial direction was affected by the level of the packing and the compression pressure.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.432-437
• /
• 2001

It is necessary to improve mechanical and optical porperties in the optical disk substrates as the information storage devices with high storage density using blue laser are being developed. Injection compression molding is regarded as the most suitable process to manufacture optical disk substrates for quality recording and read-out. In the present research, the effects of processing conditions and the insulation layer thickness on gapwise birefringence and the land-groove pattern were investigated. It was found that the values of the birefringence distribution were very sensitive to mold temperature history, and the level of birefringence reduced and, furthermore, the quality of replication was improved due to the insulation layer.

• Journal of Information Display
• /
• 제13권4호
• /
• pp.139-143
• /
• 2012

In this study, optical simulation was used to compare three optical structures that could be applied to the typical organic light-emitting diode to increase the outcoupling efficiency. These were spherical scattering particles (treated as Mie scatterers) embedded in the glass substrate, microlenses formed on the glass substrate, and a diffusing layer (DL) with a Gaussian scattering distribution function inserted between the indium tin oxide (ITO) and the glass substrate. It was found that the application of microlens array and that of scattering particles in the glass substrate exhibited similar enhancements in the outcoupling efficiency when the density and the refractive index of the scattering particles were optimized. The DL located at the interface between the glass and the ITO further enhanced the efficiency because it could further extract the trapped light in the waveguide mode. The appropriate combination of these three structures increased the outcoupling efficiency to about 42%, which is much greater than the typical values of 15-20% when there is no optical structure for light extraction.