• Korean Journal of Optics and Photonics
• /
• v.15 no.3
• /
• pp.241-247
• /
• 2004

The collimator is necessary for the assembly and evaluation of high resolution satellite telescope. Traditionally, the off-axis paraboloid has been used as a collimator. However, it has some disadvantages in that it can suffer from air turbulence when the focal length of a collimator is long, which may result in some error in the measurement. In contrast, since the Cassegrain type collimator folds the beam, it occupies smaller space compared to the off-axis paraboloid for the same focal length. This can reduce the air turbulence, which can improve the measurement accuracy. In this paper, we explain the process of design and manufacturing of a diameter 450 mm Cassegrain type collimator, to evaluate the diameter 300 mm satellite telescope. After assembly of primary and secondary mirrors, the final wavefront error of the collimator was 0.07λ(λ=633 nm), which is the diffraction limit.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.4
• /
• pp.500-505
• /
• 2011

In this paper, two types of micro-optic submersion detection systems are proposed and demonstrated. The structures are based on the transmission and reflection of incident light, respectively. Two collimators are separated by 10 mm and installed face to face in straight line. The incident light transmits from one side of collimator to the other through the air, but the optical loss is below 1 dB. On the other hand, when the sensors are submersed into water, most of optical power scattered into water. The systems monitor the dramatical power change to alarm the submersion. Reflection type of sensor system has a Bragg grating at the end of the sensor for back-reflection of sensing signal. This is for simple configuration of systems. The performance of two sensor systems are described in detail.

• Proceedings of the Optical Society of Korea Conference
• /
• 2005.07a
• /
• pp.242-243
• /
• 2005

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.02a
• /
• pp.211-212
• /
• 2006

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.594-596
• /
• 2000

The best simulation condition for the fiber collimator that uses ball lenses was investigated. This kind of fiber collimator can be used in a Micro-Optical-Cross-Connects(MOXC). MOXC is composed of collimating ball lenses, micro mirrors and single-mode fibers. In order to design a MOXC, it is very important to calculate beam path, beam radius, divergence angle that determines the insertion loss of the MOXC. Since the beam profile from the fiber facet is not exact Gaussian profile, it was found that the simulation condition in which beam waist exists on the fiber facet, ignoring Numerical Aperture(NA), gives best agreement with the experimental results. Beam radii were measured with conventional knife edge method.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.177-187
• /
• 2002

Some kinds of precision optical systems for spaceborne high resolution cameras were designed at preliminary design level and an optical design for a hyperspectral imager was performed for its development model. A Cassegrain-based catadioptric system and an unobscured reflective triplet system are illustrated in detail for spaceborne high resolution electro optical cameras which have performance of 5m resolution at an altitude of 685km and the design are evaluated in its spot-diagram and MTF to prove they have good performance enough to implement the requirements for realistic satellite payload taking the fabrication conditions and the on-orbit operation into consideration. For the development of hyperspectral imager as a next-generation payload, an optical system has been designed and elaborated. It can be divided into two parts, a catoptric telescope forming an off-axis 2 mirror type and a dispersive spectrometer which comprises collimator, grating and reimaging lens cell. From its optical design to the system characteristics are shown with the MTF performance reaching 25% approximately.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.1
• /
• pp.55-61
• /
• 2015

When a radiation detector is applied to the measurement of the radioactivity of high-level of radioactive materials or the rapid response to the nuclear accident, several collimators with the different inner radii should be prepared according to the level of dose rate. This makes the in-situ measurement impractical, because of the heavy weight of the collimator. In this study, an IRIS collimator was developed so as to have a function of controlling the inner radius, with the same method used in optical camera, to vary the attenuation ratio of radiation. The shutter was made to have the double tungsten layers with different phase angles to prevent the radiation from penetrating owing to the mechanical tolerance. The performance evaluation through the MCNP code was conducted by calculating the attenuation ratio according to the inner radius of the collimator. The attenuation ratio was marked on the outer scale ring of the collimator. It is expected that when a radiation detector with the IRIS collimator is used for the in-situ measurement, it can change the attenuation ratio of the incident photon to the detector without replacing the collimator.

• 연구논문집
• /
• s.32
• /
• pp.23-34
• /
• 2002

Up to now, collimators have teen generally produced by handwork and only a few companies have produced by semi-automatic system. Under this situation, automatic system for assembly of optical collimators has risen as a mast essential technique in the development of optical communication components. In this study, it was constructed to develop optical collimators with high functionality and we manufactured optical collimators with a GRIN rod lens and spherical lens using automatic system. Therefore, we worked a performance test through a comparison of collimators made by automatic system and handwork with angle augment, bean size. Also we selected a optimum assembly condition of GRIN rod lens and spherical lens. As a result, it brought a reduction of the tact time and an improvement of an efficiency and a productivity of optical collimators, therefore it was found that automatic system was indispensable for materialization of optical collimators with high functionality.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.103-110
• /
• 2006

Automatic optical alignment modules are a key technology in optical communication system. However, the optic component assembly depends highly on manual or semi-automated alignment process. In this paper, a novel alignment mechanism with minimum degree-of-freedom has been designed and theoretical models are derived from geometric optical characteristics on collimators, optical filters and optical ray alignment. The automatic alignment control algorithm has been newly developed based on the mechanism and models, and then we make fast, precise and reliable alignment through the algorithm. The reliability of developed modules has been verified with various simulations and performance evaluations.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.119-122
• /
• 2002

Collimators were mostly produced by handwork and semi-automatic system in some companies. Under this situation, automatic manufacturing system for optical collimators is on the rise most essential technique in the development of optical communication components. In this study, automatic manufacturing system was designed and constructed to develop optical collimators with high functionality. Also optical collimators were manufactured using a developed automatic system. We have compared collimators made by automatic system and handwork fer performance test with a measured values of angle alignment, beam size and TIL. As a result, it brought a reduction of the tact time fur manufacturing and improvement of an efficiency of optical collimators, and then it was found that automatic system was indispensable for materialization of optical collimators with high functionality.