• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.2
• /
• pp.167-175
• /
• 2020

The Two-fluid Model, proposed by Herman and Prigogine in 1979, is a macroscopic model for describing network operability in urban networks. Since the Two-fluid Model parameters change according to the traffic flow characteristics, it is necessary to identify the cause of flow change when analyzing the operability using the parameters. This study compared the crash risk according to rainfall using the Two-fluid Model parameters, and explained that the driving behavior affects the operability of the urban network. The results of the parameters estimation showed poor network operation under rainfall condition. The factors of drivers' crash risk perception model were calculated, and driving behavior was analyzed due to crash risk according to rainfall. In both the morning and evening, drivers tended to slow down their speeds to reduce the crash risk, because the risk on rainy days could be high when the speed was the same as on a sunny days. However, the crash risk was still higher on rainy days than sunny. In the future, it is necessary to analyze the relationship between the network operation and the crash risk in various networks and to improve both.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.264-272
• /
• 2011

Shipbuilders carry out the operation test to check the conditions of the main propulsion system and auxiliaries for moored vessel in the quoy before the sea trial. The estimation of the thrust and torque for the partially submerged propeller should be prepared to ensure the safety of mooring line and the ship. In this paper, the variations of the thrust and torque according to the shaft submergence and the propeller rotating speed in bollard pull condition are investigated with the model test and the numerical analysis. Based on these resaearch, the empirical formula representing the physical phenomena of the partially submerged propeller is derived and validated through comparison to measurement results of full-scale propellers under the quoy operation test.

• Steel and Composite Structures
• /
• v.34 no.5
• /
• pp.681-698
• /
• 2020

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D₃ with PVD-TiN coated (Al₂O₃-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L₁₈ orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al₂O₃+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.4
• /
• pp.897-905
• /
• 2015

This research suggested the traffic signal calculation model of active transit signal priority using a shockwave model. Using this signal priority timing optimization model, the shockwave area is computed under the condition of Early Green and Green Extension among active transit signal priority techniques. This study suggested the speed estimation method of backward shockwave using average travel time and intersection passing time. A shockwave area change is calculated according to signal timing change of transit signal priority. Moreover, this signal timing calculation model could determine the optimal signal priority timings to minimize intersection delay of general vehicles. A micro simulation analysis using VISSIM and its user application model ComInterface was applied. This study checked that this model could calculate the signal timings to minimize intersection delay considering saturation condition of traffic flow. In case studies using an isolated intersection, this study checked that this model could improve general vehicle delay of more over ten percentage as compared with equality reduction strategy of non-priority phases. Recently, transit priority facilities are spreading such as tram, BRT and median bus lane in Korea. This research has an important significance in that the proposed priority model is a new methodology that improve operation efficiency of signal intersection.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.581-588
• /
• 2020

This study examined a brake pad wear compensation method for an Electro-Mechanical Brake (EMB) using the braking test device. A three-phase Interior Permanent Magnet Synchronous Motor (IPMSM) was applied to drive the actuator of an EMB. Current control, speed control, and position control were used to control the clamping force of the EMB. The wear compensation method was performed using a software algorithm that updates the motor model equation by comparing the motor output torque current with a reference current. In addition, a simple first-order motor model equation was applied to estimate the output clamping force. The operation time to the maximum clamping force increased within 0.1 seconds compared to the brake pad in its initial condition. The experiment verified that the reference operating time was within 0.5 seconds, and the maximum value of the clamping force was satisfied under the wear condition. The wear compensation method based on the software algorithm in this paper can be performed in the pre-departure test of rolling stock.

• Journal of Korean Society of Transportation
• /
• v.24 no.1 s.87
• /
• pp.29-38
• /
• 2006

After the first opening of the KTX in April 2004, travel time between major cities has been dramatically reduced. The reduction rates range from 32% to 47%. Considering travel time reduction between major cities, this study concerned about the intercity travel impact of the KTX operation. This study aimed to analyze intercity mode choice behavior of Daegu Citizens according to the first opening of the KTX. This study takes place in two sections. These are (i) the section of KTX between Daegu and Seoul, and (ii) the section of KTX between Daegu and Daejeon. This study estimated empirical models for analyzing intercity mode choice behavior according to the first opening of the KTX. This study makes use of the data from travel survey from Daegu metropolitan area. The main part of the survey was carried out in the KTX Dong-Daegu station. The survey data includes the information on travel from Daegu to Daejeon and from Daegu to Seoul. In order to analyze intercity choice behavior according to the frist opening of the KTX, multinomial model structure is used. For the model specification, a variety of behavioral assumptions about the factors which affect the mode choice, were considered. From the empirical model estimation, it is found that OVTT(Out-of-Vehicle Travel Time), OVTC(Out-of-Vehicle Travel Cost), IVTT(In-Vehicle Travel Time), IVTC(In-Vehicle Travel Cost), travel frequency, travel purpose, sex, age, occupation. household income, individual income are significant in choosing intercity travel mode. However, it is found that the intercity nde choice behavior is different between (i) the section of KTX between Daegu and Seoul, and (ii) the section of KTX between Daegu and Daejeon. Furthermore, some policy implications are discussed in conclusion.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.3
• /
• pp.19-25
• /
• 2009

In this thesis, design effective elimination interference algorithm of ICS repeat system for repeater that improve frequency efficiency. Error convergence speed and accuracy of LMS Algorithm are influenced by reference signal. For improve LMS Algorithm, suggest Adaptive channel estimate algorithm. For using channel characteristic, adaptive channel estimate algorithm make reference signal similar interference signal by convolution operation and complement LMS algorithm demerit. For make channel similar piratical channel, apply Jake's Rayleigh multi-path model that random five path with 130Hz Doppler frequency. LMS algorithm and suggested adaptive channel estimate algorithm that have 16 taps apply to ICS repeat system under Rayleigh multi-path channel, so simulate with MATLAB. According to simulate, ICS repeat system with LMS algorithm show -40dB square error convergent after 150 datas iteration and ICS repeat system with adaptive channel estimate algorithm show -80dB square error convergent after 200 datas iteration. Analyze simulation result, suggested adaptive channel estimate algorithm show more three times iteration performance than LMS algorithm, and 40dB accuracy.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.2
• /
• pp.92-104
• /
• 2017

Previous management for speed in road traffic system was aimed only to the improvement of mobility and safety. However, consideration for the aspect of environment and energy consumption efficiency was valued less than the former ones. Nevertheless, economical damage scope caused by climate change has been increasing and it is estimated that environmental value will be increased because of the change of external circumstances. In addition, policy for reducing carbon emission in transportation system was assessed as insufficient in improving the condition of traffic road since it only focused on the transition of private vehicle into public transportation and development of eco-friendly car. Now it is the time to prepare for the adaptation strategy and precaution for the increased number of private vehicle in Korea. For this, paradigm shift in traffic operation which includes the policy not only about the mobility but also about caring environment would be needed. It is needed to be able to monitor the actual amount of greenhouse gas in real time to reduce the amount of emitted greenhouse gas in the aspect of traffic management. In this research, a methodology which can build on-line greenhouse gas emission monitoring system by using real time traffic data and predicting the circumstance in next 5 minutes was suggested.