• 한국산학기술학회논문지
• /
• 제14권4호
• /
• pp.1903-1907
• /
• 2013

심장 질환의 이상 현상은 항상 나타나는 것이 아니므로 오랜 시간 동안 심장상태를 관찰해야 한다. 하지만, 의료장비는 크기, 장비 조작, 비용 면에서 개인이 소유하여 장시간 동안 건강 체크를 하기에는 어려움이 있다. 본 논문에서는, 젤리스 금속 전극으로 측정 가능한 휴대용 디지털 심전도계를 제작하였다. 전극은 기존의 젤 타입 전극 대신 젤리스 금속 전극을 사용함으로써 기존 젤 타입 전극의 단점이었던 피부발진 또는 가려움증 유발 등의 문제점을 개선하였다. 전체 심전도계는 크게 아날로그 계측 회로부와 디지털 회로부로 구성하였다. 아날로그 계측 회로부는 동상모드 잡음을 효과적으로 제거할 수 있는 op-amp와 smd타입의 수동소자를 사용하여 18*25mm 크기로 설계 및 구현하였다. 디지털 회로부에서는 마이크로 컨트롤러를 이용하여 아날로그 신호인 심장신호를 디지털 신호로 변환하여 TFT-LCD에 디스플레이할 수 있도록 하였다. 완성된 휴대용 심전도계의 크기는 25*80*50mm이고, 무게는 약 150g 정도로써 가볍고 휴대하기 용이하게 소형으로 제작하였다.

• Tribology and Lubricants
• /
• 제28권6호
• /
• pp.265-271
• /
• 2012

In the preceding Part I study, for improving the unbalance response vibration of a large PRT motor-generator rotor fundamentally by design, a series of design analyses were carried out for bearing improvement by retrofitting from original plain partial journal bearings, applied for operation at a rated speed of 1,800 rpm, to final tilting pad journal bearings. To satisfy evenly key basic lubrication performances such as the minimum lift-off speed and maximum oil-film temperature, a design solution of 5-pad tilting pad journal bearings and maximizing the direct stiffness by about two times has been achieved. In this Part II study, a detailed rotordynamic analysis of the large PRT motor-generator rotor-bearing system will be performed, applying both the original plain partial journal bearings and the retrofitted tilting pad journal bearings, to confirm the effect of rotordynamic vibration improvement after retrofitting. The results show that the rotor unbalance response vibrations with the tilting pad journal bearings are greatly reduced by as much as about one ninth of those with the plain partial journal bearings. In addition, for the tilting pad journal bearings there exist no critical speed up to the rated speed and just one instance of a concerned critical speed around the rated speed, whereas for the plain partial journal bearings there exist one instance of a critical speed up to the rated speed and two instances of concerned critical speeds around the rated speed.

• 한국소음진동공학회논문집
• /
• 제23권1호
• /
• pp.65-72
• /
• 2013

This case study presents a practical method to reduce resonant vibration of large vertical pumps. The pumps are driven at 400 rpm rated speed by induction motor. The vibration was not significantly large when operated at this rated speed. Large vibration was occurred when the pump was operated below the rated speed for flow control. Due to the large vibration resonance, variable speed operation of the pump was not possible for several months at worst cases. To find an efficient vibration control method, the flexural responses of pumps for both normal and transient operations were measured. The measured modal characteristics were compared with those of finite element analysis. When the pump was operated at a specific rpm, the natural mode whose resonance frequency is twice the rotating angular speed induced the large vibration. The retrofit utilizing stiffeners to reduce this resonant vibration were performed. Effects of designed stiffeners on reducing vibration were validated through tests after actual installation.

• 한국통신학회논문지
• /
• 제29권9A호
• /
• pp.991-997
• /
• 2004

본 논문은 HomePNA 2.0 모뎀 칩을 위한 모뎀 수신부의 구조를 제안한다. HomePNA 2.0 전송 채널은 브릿지 탭과 HAM 대역의 영향 등으로 매우 열악하다. 이러한 채널을 통해 전송을 가능하게 하기 위해 HomePNA 2.0 은 훈련신호를 사용하여 매 프레임 마다 채널을 등화하고 FD-QAM 전송 방식을 선택적으로 사용한다. 따라서 모뎀 수신부는 일반적 QAM 방식 신호의 북조 기능과 함께 이러한 전송 방식의 특정을 최대한 상려 모뎀 수신 성 능을 극대화 히는 구조가 필요하다 연구 결과 모뎀 수신부의 가능을 송수신 상태에 따라 정상 수신 모드와 충돌 감지 오드의 2 가지로 정의 하였다 본 논문은 특히, 모뎀 수신부를 구성하는 핵심 블록인 등화기와 위상 동기부, 프레임 동기부에 대해서 사용된 알고리즘을 밝혔으며, 버스트 방식 모뎀의 채널 등화 성능을 높이고 안정적으로 동작 시키기 위한 구조를 제얀 하였다 마지막으로 제안된 모뎀 수신부의 성능을 분석하기 위해서 SPW 모델을 사용하여 채널 별 전송 가능 속도를 예측 하였다.

• 한국통신학회논문지
• /
• 제31권8C호
• /
• pp.763-770
• /
• 2006

본 논문에서는 소실 복호 기능을 갖는 가변형 Reed-Solomon(RS) 복호기가 수정 유클리드 알고리즘(modified Euclid's algorithm; MEA)을 기반으로 설계되었다. 복호기의 가변성은 원시 RS(255, 239, 8) 부호와는 다른 RS(124, 108, 8) 부호를 기반으로 단축과 펑처링을 통해 구현된다. 이렇게 하므로써 복호 시간을 단축시켰다. 복호기는 4단계 파이프라인 구조를 갖으며, 파이프라인의 각 단계는 서로 다른 클럭으로 동작할 수 있도록 설계하였다. 따라서 MEA 블록에 고속 클럭을 사용하므로써 복호기의 복잡도 및 복호 지연을 단축할 수 있으며, 버스트 및 연속 모드의 복호를 모두 지원한다. 설계된 복호기는 VHDL로 구현하고 FPGA에 합성하였으며, 3,717개의 로직 셀과 2,048 비트의 메모리가 사용되었다. 설계된 복호기는 최고 33MByte/sec의 데이터를 복호 할 수 있다.

• 한국물환경학회지
• /
• 제22권2호
• /
• pp.358-363
• /
• 2006

KSMBR process is dynamic state advanced wastewater treatment applied with Trisectional Aeration (TSA) mode combined with membrane. TSA was remodeled conventional intermittent aeration which was operated nonaeration-aeration. TSA operates nonaeration ($N_1$) - aeration (A) - nonaeration ($N_2$) in Trisectional Aeration Reactor (TAR). Organics of influent could be nearly consumed to denitrification without influence by remained DO in TAR and it could be operated about sludge return ratio of 1Q (influent base). The purpose of this study was to apply KSMBR to the full-scale plant and to evaluate efficiency of nitrogen and phosphorus removal and TSA operation. The result of this study, average CODcr/T-N and CODcr/T-P ratio were 7.8 and 59.6, respectively. BOD, TCODcr, SS, T-N, T-P, E-coli removal efficiency were 98.4, 95.2, 73.0, 69.6, 99.95 %, respectively. KSMBR obtained high removal efficiencies of C, N and P when it applied full-scale plant.

• 한국물환경학회지
• /
• 제25권6호
• /
• pp.896-901
• /
• 2009

In this study, in order to apply the air and pure oxygen in the Jet Loop Reactor (JLB) in which the oxygen transfer rate is high, differentiate the operation mode according to each air flowrate and liquid flowrate and investigate the oxygen transfer characteristic, an experiment was carried out. The oxygen concentration with the air flowrate ($Q_g$) and liquid flowrate ($Q_L$) was identical but the oxygen transfer coefficient ($K_L{\cdot}a$) is linear depending on degree of two factors. The width of an increase is small in $0.1min^{-1}$ when the air flowrate is 0.2 L/min with increasing the liquid flowrate. Whereas, the increment was exposed to be very high for $1.5min^{-1}$ when the air flowrate was 5 L/min. In the experiments using the pure oxygen, it was 30 mg/L of oxygen concentration finally and it was 3.5 times than using the air. But the time reached the saturated concentration was similar to using the air, and $K_L{\cdot}a$ was similar to using the air too. Analysis between two independent variable and oxygen transfer of the correlation is the same model like $K_L{\cdot}a={0.0161Q_L}^{1.5371}{Q_g}^{0.5433}$ using with coefficient non linear regression analysis. It was resulted that the liquid flowrate were approximately three times than air flowrate on effect to oxygen transfer rate.

• 멤브레인
• /
• 제16권3호
• /
• pp.188-195
• /
• 2006

본 연구의 목적은 침지형(YEF 750D-2) 모듈을 적용하여 공기유량에 따른 유체 유속과 간헐적인 세정공기의 공급에 의한 오염제거를 평가하는 것이다. 공기유량에 따라 모듈의 유체 유속은 선형적으로 증가하였으며, MLSS의 농도가 1,000 mg/L 증가할 때 마다 $3\times10^{-4}m{\cdot}min/sec{\cdot}L$의 비율로 유체 유속이 감소하였다. 세정공기의 공급이 정지되는 시간에 전여과가 일어나 흡인여과 시간 동안 겔층 위에 케익층이 형성되었다. 20초 정지와 20초 공기공급의 간헐공기주입으로 형성된 케익층이 역세정에 의하여 제거되면서 압력증가율이 가장 낮게 나타났다. 겔층이 제거되는 메커니즘은 세정 공기공급을 교대로 하여 겔층 위에 케익층을 형성시켜 케익층이 제거될 때 겔층이 함께 제거되는 원리로 설명할 수 있다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.199-199
• /
• 2011

Recently, Thin film transistors (TFTs) with amorphous oxide semiconductors (AOSs) can offer an important aspect for next generation displays with high mobility. Several oxide semiconductor such as ZnO, $SnO_2$ and InGaZnO have been extensively researched. Especially, as a well-known binary metal oxide, tin oxide ($SnO_2$), usually acts as n-type semiconductor with a wide band gap of 3.6eV. Over the past several decades intensive research activities have been conducted on $SnO_2$ in the bulk, thin film and nanostructure forms due to its interesting electrical properties making it a promising material for applications in solar cells, flat panel displays, and light emitting devices. But, its application to the active channel of TFTs have been limited due to the difficulties in controlling the electron density and n-type of operation with depletion mode. In this study, we fabricated staggered bottom-gate structure $SnO_2$-TFTs and patterned channel layer used a shadow mask. Then we compare to the performance intrinsic $SnO_2$-TFTs and doping hafnium $SnO_2$-TFTs. As a result, we suggest that can be control the defect formation of $SnO_2$-TFTs by doping hafnium. The hafnium element into the $SnO_2$ thin-films maybe acts to control the carrier concentration by suppressing carrier generation via oxygen vacancy formation. Furthermore, it can be also control the mobility. And bias stability of $SnO_2$-TFTs is improvement using doping hafnium. Enhancement of device stability was attributed to the reduced defect in channel layer or interface. In order to verify this effect, we employed to measure activation energy that can be explained by the thermal activation process of the subthreshold drain current.

• 한국의류학회지
• /
• 제27권9_10호
• /
• pp.1081-1092
• /
• 2003

The purpose of this study was to identify the current situation of textiles and apparel firms in the overseas markets and to examine the relationship between firms' characteristic(i.e., sales volume) and international marketing strategies. A random sample of 311 textiles and apparel firms were selected. The survey design method was used to test conceptual framework. Adjusted response rate was 33.4%(n=115). Descriptive analysis (i.e., frequency, percent) and $\chi$$^2$-test were used for data analysis. About the current situation of textiles and apparel firms in the overseas markets, the motivation for international market entry was highly found to expand their operation from domestic to international market, and most firms were found to be involved with OEMs(Original Equipment Manufacturers) as an entry mode for international market. China and US market were the most popular market among Korean textiles and apparel firms. Product differentiation strategy, pricing strategy based on manufacturing cost and buyer's offering price, place strategy using foreign buyers and participating a few international exhibition were frequently used among Korean textiles and apparel firms for international marketing. Among textile firms, sales volume was related to product strategies(product development), price strategy(buyer's offer) and place strategy(channel). Among apparel firms, product strategy(product labeling), price strategy(price satisfaction). The findings of this can be used when Korean textiles and apparel firms do strategic planning and evaluate the international marketing strategies. Also information and results of this study may assist policy makers to develop better ideas and strategies for textiles and apparel industry.