• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.9
• /
• pp.676-680
• /
• 2010

In this paper, Fin-type silicon-oxide-nitride-oxide-silicon (SONOS) flash memory are fabricated and the electrical characteristics are analyzed. Compared to the planar-type SONOS devices, Fin-type SONOS devices show good short channel effect (SCE) immunity due to the enhanced gate controllability. In memory characteristics such as program/erase speed, endurance and data retention, Fin-type SONOS flash memory are also superior to those of conventional planar-type. In addition, Fin-type SONOS device shows improved SCE immunity in accordance with the decrease of Fin width. This is known to be due to the fully depleted mode operation as the Fin width decreases. In Fin-type, however, the memory characteristic improvement is not shown in narrower Fin width. This is thought to be caused by the Fin structure where the electric field of Fin top can interference with the Fin side electric field and be lowered.

• Journal of KIISE:Information Networking
• /
• v.34 no.4
• /
• pp.287-295
• /
• 2007

IETF's FMIPv6 protocol enables a mobile node to switch to the reactive mode of handover operation when the prediction of the movement is incorrect. In this case, the mobile node may experience severe service disruption due to large handover latency and packet loss. In order to solve this problem, we propose a fast mobile IP handover with multiple pre-registrations. In the proposed approach, the new temporary IP addresses are prepared in advance at multiple locations where the mobile node may probably move into. In this case, even though the prediction is wrong, the mobile node can move into the alternative locations without causing service disruption. We have designed and implemented a prototype system, and measured the performance of the proposed system. The experimental results show that the proposed approach can reduce the handover latency drastically.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2014.06a
• /
• pp.79-80
• /
• 2014

Most of marine pollution have been occurred by oil spill accidents resulted from ship accidents in South Korea. This year there were two large oil spill accidents: the Yeosu Oil Spill Accident (2014.01.31.(Fri.) 09:35 LT) and the Captain Vangelis L. Oil Spill Accident (2014.02.15.(Sat.) 14:00 LT). In general, Synthetic Aperture Radar (SAR) is used in monitoring and detection of oil dumping and spilled oils by accident at sea. Therefore it is expected that KOMPSAT-5, launched successfully last year, will take part in that mission during a normal operation mode. After the two accidents, high spatial resolution optical satellite data including KOMPSAT-3 were acquired February 2 and 14, 2014. In this presentation, we analyzed optical properties of spilled oils from optical satellite imagery to estimate the spilled area and the volume at each region. Finally, a satellite application planning for ocean surveillance in South Korea will be presented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.4
• /
• pp.387-393
• /
• 2013

In shipyard site, a ship is constructed by integrating lots of modules that are made in several sites with different capabilities and specifications. Recently, it needs to make a shipyard to be smart with wired and wireless broadband networks between hierarchical shipyards. In this paper, we propose an installation of LTE femtocell local gateway at a remote shipyard, an information exchange method between hierarchical shipyards, and an offload method to separate the general traffic. We define the mode change in a femtocell gateway for supporting the offload of the general traffic between the headquarter and a remote shipyard, the offload data management and trigger message, and cache entry fields. To show the operation of our proposed off-loading function, we consider the transcipient message flow at the femtocell gateway with its state transition diagram. Hence, it is expected to increase the productivity of shipyard industry with mobile communications and broadband Internet technologies.

• Journal of KIISE:Information Networking
• /
• v.30 no.2
• /
• pp.270-281
• /
• 2003

ETF made the RFCs of MPLS technologies for providing the QoS of ATM or Frame Relay and the flexibility&scalability of IP on the Internet services. IETF has been expanding MPLS technologies as a common control component for supporting the various switching technologies called GMPLS. Also, IETF has standardized the signaling protocols based on such technologies, such as LDP, CR-LDP and RSVP-TE. ETRI developed the MPLS system based on ATM switch in order to provide more reliable services, differentiated services and value-added services like the VPN and traffic engineering service on the Korea Public Sector network. We are planning on deploying model services and commercial services on that network. This paper explains the basic functions of LDP, design and development of LDP on our system, and compares with LDP development and operation on other MPLS systems made by Cisco, Juniper, Nortel and Riverstone. In conclusion, this paper deduces the future services and applications by LDP through these explanation and comparison.

• The Journal of the Korea Contents Association
• /
• v.10 no.9
• /
• pp.57-67
• /
• 2010

Smart grid technology can expand energy efficiency into the home by monitoring consumer energy usage in real time and communicating with household devices that respond to demands to shut off during periods of non-use, allowing individual consumers to control their electricity usage more effectively. But, the information collected on a smart grid will form a library of personal information, the mishandling of which could be highly invasive of consumer privacy. There will be major concerns if consumer-focused principles of transparency and control are not treated as essential design principles from beginning to end. In this paper, using. All-Or-Nothing Transform encryption mode for providing smart grid security, we propose efficient distributed data Management based on XOR operation. The contribution of this paper is to provide a secure algorithm that manages efficiently distributed data in the field of private data in smart grid environment.

• Korea-Australia Rheology Journal
• /
• v.16 no.3
• /
• pp.141-146
• /
• 2004

Shear-induced damage of Red Blood Cell (RBC) is an imminent problem to be solved for the practical application of artificial organs in extra corporeal circulation, as it often happens and affects physiological homeostasis of a patient. To design and operate artificial organs in a safe mode, many investigations have been set up to correlate shear and shear-induced cell damage. Most studies were focused on hemolysis i.e. the extreme case, however, it is important as well to obtain a clear understanding of pre-hemolytic mechanical damage. In this study, the change in deformability of RBC was measured by ektacytometry to investigate the damage of RBC caused by shear. To a small magnitude of pre-shear, there is little difference, but to a large magnitude of pre-shear, cell damage occurs and the effect of shear becomes significant depending on both the magnitude and imposed time of shearing. The threshold stress for cell damage was found to be approximately 30 Pa, which is much less than the threshold of mechanical hemolysis but is large enough to occur in vitro as in the extra corporeal circulation during open-heart surgery or artificial heart. In conclusion, it was found and suggested that the decrease of deformability can be used as an early indication of cell damage, in contrast to measuring plasma hemoglobin. As cell damage always occurs during flow in artificial organs, the results as well as the approach adopted here will be helpful in the design and operation of artificial organs.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.9
• /
• pp.878-885
• /
• 2009

One of important factors in designing MEMS resonators for RF filters is obtaining a desired frequency response function (FRF) within a specific frequency range of interest. Because various array-type MEMS resonators have been recently introduced to improve the filter characteristics such as bandwidth, pass-band, and shape factor, the degrees of freedom (DOF) of finite elements for their FRF calculation dramatically increases and therefore raises computational difficulties. In this paper the Krylov subspace-based model order reduction using moment-matching with non-zero expansion points is represented as a numerical solution to perform the frequency response analyses of those array-type MEMS resonators in an efficient way. By matching moments at a frequency around the specific operation range of the array-type resonators, the required FRF can be efficiently calculated regardless of their operating frequency from significantly reduced systems. In addition, because of the characteristics of the moment-matching method, a minimal order of reduced system with a prearranged accuracy can be determined through an error indicator using successive reduced models, which is very useful to automate the order reduction process and FRF calculation for structural optimization iterations. We also found out that the presented method could obtain the FRF of a $6\times6$ array-type resonator within a seventieth of the computational time necessary for the direct method and in addition FRF calculation by the mode superposition method could not even be completed because of a data overflow with a half after calculation of 9,722 eigenmodes.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.6
• /
• pp.647-657
• /
• 2012

Although nuclear power plant piping system is designed conforming to design specifications, the piping systems are deteriorated with increase in service life. In this study, monotonic and cyclic loading tests were carried out on TP316 stainless steel pipe specimens, and the effect of local wall thinning and cracking on failure behavior was investigated. In the tests, 0%, 35% and 75% wall thinning and cracking of initial thickness were artificially introduced to inside elbow and straight pipe specimens, and internal pressures of 20MPa were applied to simulate real operation condition. From the test results, the effect of local wall thinning and cracking on failure mode, ultimate load, number of cycle and strain energy was presented, and maximum bending moment was compared with allowable bending moment calculated by ASME code.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.12
• /
• pp.1115-1120
• /
• 2007

This paper presents a novel mechanism of electro-spray micro-thruster featured by a nozzle with a conductive pole inside, referred to here as a pole type nozzle. And the effects of the pole type nozzle on the efficiency of the jetting are numerically and experimentally investigated. The electric voltage signal applied to the upper electrode plate, against the pole as the ground, allows a ejection of spray to take place. It is verified experimentally that the use of the pole type nozzle allows a stable and sustainable jetting mode of ejection for a wider range of applied voltages because it can concentrate the electric field more on the centre of the meniscus. According to results about size effect, experiments indicates that the proposed mechanism allows that operation of micro thruster at less than 500 volts through nanoscale nozzle.