• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.6
• /
• pp.451-458
• /
• 2020

In this study, a trade-off analysis of a power conversion system (PCS) is performed in accordance with a power semiconductor device to establish the suitable operating frequency range for the anyplace induction heating system. A resonant network is designed under each operating frequency condition to compare and analyze the PCS losses depending on the power semiconductor device. On the basis of the simulation results, the PCS losses and frequency condition are calculated. The calculated results are then used for a trade-off analysis between Si-MOSFET and GaN-HEMT based on PCS. The suitable operating frequency range is determined, and the validity of the analysis results is verified by the experiment results.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.3
• /
• pp.256-263
• /
• 2009

The operating range of HCCI engine is narrow due to excessive rate of pressure rise on high load. The fuel stratification is proposed to solve the problem. The purpose of this study is to gain a better understanding of the effects of fuel stratification on reducing the pressure-rise rate at high load in HCCI combustion and to investigate that the operating range is expanded for fuel stratification in the preceding condition of initial temperature and equivalence ratios. The engine is fueled with Di-Methyl Ether (DME) which has unique 2-stage heat release. The computations were conducted using SENKIN application of the CHEMKINll kinetics rate code. Calculation result shows that proper fuel stratification prolongs combustion duration and reduce pressure rise rate.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.422-427
• /
• 2000

The design of low-solidity vaned diffusers and the effect on the performance of a turbocharger compressor is discussed. The effect of vane number and turning angle was investigated while maintaining a basic design with a leading edge angle of $70^{\circ}$, leading and trailing edge radius ratios of 1.1 and 1.3. All results are compared with those obtained with the standard vaneless diffuser configuration and it was shown that all designs increased and shifted the pressure ratio to reduced flowrates. Despite the low-solidity configuration none of the vane designs provided a broad operating range, and the vane leading edge angle was not main factor that system went into the surge condition. The diffuser of higher trailing edge angle improved the flow range for the compressor to operate at lower flow region.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.69-76
• /
• 2009

This paper describes sensorless high-speed control for 45,000rpm/22kw type PMSM by using iterative adaptive sliding mode observer. The proposed algorithm is based on sensorless vector control by on-line estimating the speed of rotor in the wide speed operating range between the starting operation. In addition, it shows the enhanced performance of the iterative adaptive observer by lessening its chattering and getting stable response in limited PWM period. The simulation and experiment results show the reliable performance of the proposed algorithm through starting to high speed operating range.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.215-218
• /
• 2002

Design methods are presented for a broadband corrugated horn antenna operating X/Ku band (7.25-14.5 CHz). The corrugated horn consists of a circular waveguide taper, a mode converter, a waveguide-to-horn transition, and a hem section. Methods of design are presented for each section. The designed antenna shows excellent characteristics over the entire operating frequency range.

• Journal of the Korean Society of Costume
• /
• v.54 no.3
• /
• pp.65-71
• /
• 2004

Surgical operating gowns are worn by doctors and nurses in operating theater to address dual function of preventing transfer microorganisms like bacteria and body fluids from the operating staffs to patients. and also from patients to staff. They must allow necessary mobility without rubbing and must resist tearing. These gown must be designed to fit a diversity of body shapes and sizes with a limited range of sizes as hospitals will stock limited quantities. Also they must proper in various operating situations. In order to suggest improving design features of surgical gowns, it has been done to analyze current situation of medical uniform manufacturing and wearing. Surgical gown were made with plain fabric of cotton 100% and had a little size system without sexual division. Many doctors were unsatisfied with surgical gown size and wearing comfort. Surgical operating gowns need continuos research for new material and design as surgical situation, and new sizing system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.11
• /
• pp.978-984
• /
• 2015

In this paper, we designed a RF transceiver operating up to 200 km operating range and 45 Mbps data rate. The RF transceiver operates in Ku band and composed of up/down converter, high power amplifier, front-end elements. To satisfy the operating range of RF transceiver, 10W power amplifier was required and realized by using GaN power amplifier. Moreover, to mitigate mutual interference for different bandwidth signals due to the adaptive transmission speed control function, SAW filter bank structure was used. To verify system requirement satisfaction AWR simulation tool was used.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.1
• /
• pp.24-27
• /
• 2018

The performance measure of airborne radars is the range at which the cumulative probability of detection has some specified value, because the per-scan detection probability is an oscillatory function of the target range in airborne radars operating with the dynamic clutter environment. As a result, no one range, at which the per-scan detection probability has a given value, can give a meaningful description of the range performance. In this paper, we provide the equation to calculate the cumulative detection probability and show that the result of Monte Carlo simulation is same as the calculated value in a simple scenario. This verified Monte Carlo model will be used to evaluate the performance of airborne radars in various operating scenarios, at which the numerical calculation is difficult.

• The Korean Journal of Health Service Management
• /
• v.5 no.3
• /
• pp.13-23
• /
• 2011

This paper investigated the operating environment for the representative of each agency and the facility workers on the basis of analytical result of recognition changes of the operating environment changes under the operating the long-term care insurance. It was described plans to take positive effect on the operating as follows. The first, on the result of regression analysis, the service administrative range takes the biggest effect on the general recognition of executing the long-term care insurance off and on. The affirmative recognition of the service administrative range had the general recognition on the system be positive effect. But the operator of facility asserts that the care manager's professionalism related quality of service be strengthened. The second, on the result of regression analysis, in the financial accounting administrative it is revealed the more positive recognition it is, the more positive effects it has. From the difference verification of an operation size from operation subject, the small operation size and personal facility recognize the long term care insurance positively. On the other side the facilities where the operation size is big recognize the system negatively. The long-term care facility should rearrange a support program newly and the government needs to promote the donation activity, because it is needed to reduce the financial burden of facilities.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.3
• /
• pp.604-610
• /
• 2007

Injection molding is the most common method of shaping plastic resins for manufacturing a variety of parts. This injection molding is accomplished by injection molding machines (IMM) which consists of a hewer, a reciprocating screw, barrel assembly, and an injection nozzle. The plastic resin is fed to the machine through the hopper and it should be heated to the target melting temperature, which depends on material properties, as closely as possible with very small temperature overshoot in the barrel. Since the barrel, which has temperature dependent specific heat and thermal conductivity in the operating temperature range, is heated by the several electric heater bands, it is not an easy task to control the temperature of the barrel owing to the interference of neighboring heaters and its material properties. Though PID controller with auto-tuning capability is widely adopted in the nm, the auto-tuning process should be carried out whenever the operating temperature is changed significantly. Recently, though the predictive controller is developed and shows good performance, it has drawbacks: 1. Since the heat transfer modeling process is very complicated and should be carried out again when the barrel is changed, it is somewhat inappropriate in the field. 2. The controller performance is not validated in whole operating temperature range. In this paper, cascade type simple PI controller with input restriction is proposed to find the possibility of controlling the barrel temperature in the whole operating temperature range. It is shown by experiment that the proposed controller shows good performance. This result can be applied to design of PI controller with auto-tuning capability.