• Journal of Advanced Marine Engineering and Technology
• /
• 제17권4호
• /
• pp.11-19
• /
• 1993

The experimental study was carried out to investigate the stability and the performance characteristics of the aero-valved pulsating combustion system with maximum operating capacity of 60KW. The effect of geometry of combustion system on the stable condition, the flammability limit, the total pressure oscillation amplitude, and the operating frequency can be identified, and the maximum turn-down-ratio is obtained up to 3.3. The total pressure oscillation amplitude can be controlled by tunning the length of the air inlet pipe. The empirical equation with which the operating frequency can be approximated is proposed and the discrepancy is within 5%. The volumetric efficiency is identified to be one of the important parameters determining the upper flammability limit and the maximum value of which is approximately 22%.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1999년도 제19회 KOSCO SYMPOSIUM 논문집
• /
• pp.111-115
• /
• 1999

In order to enhance the burner performance of household gas fired absorption chiller/heaters, the operating condition(excess air $\approx$ 10%) of the burner currently being used was required to be optimized. In this regard, we examined where the $CO_{\min}$. emission limit was located between blow off and yellow tip limit and how much amount of excess air was exhausted by means of observing blow off and yellow tip limit. It was found that the $CO_{\min}$ limit(excess air ${\approx}$ 4%) was determined near the yellow tip limit. The effect of exhaust pressure on the $CO_{\min}$. limit was that, if exhaust pressure was higher than that in steady condition, higher air blower fan rpm is demanded to maintain the $CO_{\min}$ limit. Therefore, it was necessary to optimize the operating condition of burner in terms of a thermal efficiency and safety.

• International Journal of Automotive Technology
• /
• 제2권4호
• /
• pp.147-155
• /
• 2001

Analysis of the thermodynamic cycle of IC engine from the point of view of economy and emissions was carried out. From this analysis potential capability of engine development was derived. This potential capability is lean-burn engine, fuelled with homogeneous mixture with $\lambda \geq$ 1.4. Several different modes of fuelling were proposed and tested on one-cylinder test engine from the point of view of extending lean operating limit of the engine, emissions and fuel economy. Among them were: fuelling with evaporated preheated gasoline, with gas (LPG evaporated) and with liquid butane. From these modes, fuelling with liquid butane injected to inlet port was selected and finally tested. This novel system of fuelling offered better than standard engine performances and emissions at lean operating limit. These results were validated on full-scale two-cylinder engine.

• 전기의세계
• /
• 제24권5호
• /
• pp.97-102
• /
• 1975

This paper describes the result of a Study for the Optimum Operating method with Spinning reserve in case of outage of large generator unit to improve the system stability and prevent the system frequency drop. This is usually done by governor free operation, so we focused our attention to the operating Char acteristics of spinning reserve. Nexy, a study was made to mesure the upper limit of Spinning reserve and when this upper limit cannot match the required power, a relationship between the amount of spinning reserve and that of the load shedding requirement was searched with regard to several system operating conditions to use it in our future system operation. By this study, the optimum system operating method was recommended for reliable operation of power system.

• 한국자동차공학회논문집
• /
• 제19권2호
• /
• pp.35-41
• /
• 2011

This work investigates the potential of in-cylinder thermal stratification and fuel stratification for extending the operating ranges in HCCI engines, and the coupling between thermal stratification and fuel stratification. Computational results areemployed. The computations were conducted using both a custom multi-zone version and the standard single-zone version of the Senkin application of the CHEMKINII kinetics rate code, and kinetic mechanism for di-methyl ether (DME). This study shows that the potential of thermal stratification and fuels stratification for extending the high-load operating limit by a staged combustion event with reduced pressure-rise rates is very large. It was also found that those stratification offers good potential to extend low-load limit by a same mechanism in high-load. However, a combination of thermal stratification and fuel stratification is not more effective than above stratification techniques for extending the operating ranges showing similar results of fuel stratification. Sufficient condition for combustion (enough temperature for) turns misfire in low-load limit to operate engines, which also leads to knock in high-load limit abruptly due to the too high temperature with high. DME shows a potential for maximizing effect of stratification to lower pressure-rise rate due to the characteristics of low-temperature heat release.

• 해양환경안전학회지
• /
• 제21권6호
• /
• pp.784-789
• /
• 2015

본 연구는 소형 고속정의 운항한계를 검토하기 위하여 수행되었다. 일반적으로 내항성능의 검토는 선형의 결정 단계 전에 이루어지지만 본 연구는 선박의 건조가 완료된 후에 이루어졌다. 검토 결과, 종동요, 수직 및 수평가속도, 슬래밍의 운동성능은 특정한 조우각을 제외하고는 만족하였으나 갑판침수의 경우에는 해석을 수행한 모든 조건에서 만족하지 않았다. 이것은 대상선박의 크기가 소형이기 때문에 선박의 속도나 파도와의 조우각보다는 해상상태가 설정한 내항성능 기준의 만족 여부에 더 큰 영향을 미쳤기 때문으로 보인다.

• 한국정밀공학회지
• /
• 제29권12호
• /
• pp.1340-1345
• /
• 2012

Industrial products developed in recent years have focused on usability and stability. Especially, for the products used in daily life, steady efforts have been made to secure the safety. Among them, the products equipped with wheels such as strollers, shopping carts, and carriers can occur the safety accidents by unintended over speed at a ramp. Therefore, development of speed limit device is required to prevent such accidents. However, the existing speed limit devices are very expensive and have a complex drive principle, so it's generally difficult to apply them. In this study, a simple speed limit wheel is suggested which can replace the previous complex and inconvenient speed limit devices. The developed speed limit wheel can be simply applied to existing products by changing the wheels. In addition, it has an advantage to operate only by mechanical mechanism without power supply. Thus it can minimize the cost and waste of resources. For this purpose, the operating condition of the target products was analyzed, and trochoid gear mechanisms were selected for the speed limit. Based on this, finite element analysis was conducted to estimate the operating mechanism. After the prototype of the wheel was produced, the performance under various conditions was tested and has been improved.

• 조명전기설비학회논문지
• /
• 제26권7호
• /
• pp.92-98
• /
• 2012

It is made compulsory to install SPD for the purpose of protecting electric and electronic devices when an abnormal voltage such as lightning occurs to power line using power frequency of 60Hz. Recently, the high speed communication technology utilizing power line is receiving attention again as a communication technology for smart grid. The SPD influences the performances of power line communication when using SPD and power line communication system together. In order to improve the performance of power line communication, a proposed scheme for series connection of gas discharge tube to ZnO varistor was presented. This paper measured the impacts of series connection of GDT to SPD using ZnO varistor on the limit voltage of Class III SPD. This paper also presented the DC operating voltage of GDT which satisfies the limit voltage of power line communication system and SPD simultaneously.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.1-10
• /
• 1994

By applying of total electric capacitance method on engine connecting rod bearing during engine operating, the influence of engine operating conditions and lubricants on bearing oil film thickness was investigated. Minimum oil film thickness increases with kinematic viscosity, but as increasing of viscosity, the increasing ratio of film thickness is reduced. Also minimum oil film thickness increases with engine speed but there is a limit. Above this limit, film thickness decreases in opposition because of crankshaft inertia. As increasing of engine torque and oil temperature, munimum oil film thickness decreases linearly. For non-Newtonian oils, the correlation between $100{\circ}C$ kinematic viscosity and munimum oil film thickness is very poor.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.95-97
• /
• 2007

This paper studies on operating limit curve of low voltage electric machinery with respect to source voltage variation or sag. Also, it discusses electric machine and compensation equipment design methodology based on voltage quality effect assessment technology. Voltage quality standards, such as SEMI47, CBEMA, ITIC curve are regarded to examine the relation between time constants of load and sagging time of sag generator, the load(low voltage electric machinery) study. Voltage sag characteristics of loads, time constant and sag relation voltage-time operating limits are tested and verified.