• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.2
• /
• pp.158-162
• /
• 2004

The magnetic levitator is the device which can float a magnetic material at the midair by electromagnetic force and it's principle can be applied to the high speed magnetic bearing or magnetic levitation train. There are many difficulties to control, because the magnetic levitator is basically a nonlinear and unstable system. In this paper, this system is modeled assuming that it is a linear system nearby an operating point, and a proportional and derivative(PD) position controller is designed to carry out the variable position control. The performance of position control response is shown through simulation and experiment. A prototype magnetic levitator is constructed using PWM converter and DSP(Digital Signal Processor) based control board.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.5
• /
• pp.92-99
• /
• 2008

This paper describes an signal processing method for the hall sensorless position control of ETC control system using a BLDC motor. The proposed ETC control system, which is mainly consisted of a BLDC motor, a throttle plate, a return spring and reduction gear, has a position sensor with an analog voltage output on the throttle valve instead of BLDC motor for detecting rotor position of motor. So the additional commutation information is necessarily needed to control the mentioned ETC module. In order to estimate and determine the commutation state, it is proposed to properly manipulate the resolution of A/D converter considering the mechanical parameter, that is, the number of motor slot and the ratio of reduction gear. Through this method, the estimation of commutation state for operating the system is possible and the discrete signal for commutation is stably obtained. The validity of the method is examined through the experimental results.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.47-52
• /
• 2001

This paper presents a high-performance control system for Reluctance Synchronous Motor (RSM) drives with direct torque control (DTC). The system consist of stator flux observer, rotor position/speed estimator, torque estimator, two hysteresis band controllers, an optimal switching look-up table, IGBT voltage source inverter, and F240/C31DSP controller by using fully integrated control software. The stator flux observer is based on the combined voltage and current model with stator flux feedback adaptive control that inputs are current and voltage sensing of motor terminal with estimated rotor angle for wide speed range. The rotor position is estimated by the observed stator flux-linkage space vector. The estimated rotor speed can be determinated by differentiation of the rotor position used only in the current model part of the flux observer for a low speed operating area. To prove the suggested control algorithm, we have a simulation and testing at actual experimental system. The developed digitally high-performance position sensorless control system are shown a good motion control response characteristic results and high performance features using 1.0Kw RSM.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.1
• /
• pp.201-210
• /
• 2018

This paper proposes a new start-up method for a load commutated inverter (LCI) in a large synchronous gas-turbine generator. The initial rotor position for start-up torque is detected by the proposed initial angle detector, which consists of an integrator and a phase-locked loop. The initial rotor position is accurately detected within 150ms, and the angle difference between the real position and the detected position is less than 1%. The LCI system operates in two modes (forced commutation mode and natural commutation mode) according to operating speed range. The proposed controllers include a forced commutation controller for the low-speed range, a PI speed controller and a PI current controller, where the forced commutation controller is connected to the current controller in parallel. The current controller is modeled by Matlab/Simulink, where a six-pulse delay of the thyristor and a processing delay are considered by using a zero-order hold. The performance of the proposed start-up method is evaluated in Matlab/Psim at standstill and at low speed. To verify the feasibility of the method, a 5kVA LCI system prototype is implemented, and the proposed initial angle detector and the system performance are confirmed by experimental results from standstill to 900rpm.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.10a
• /
• pp.115-120
• /
• 2006

The rail clamp is the device to prevent the crane slips along rails from the wind blast as well as to locate a container crane in the set position in operating mode. In this study we conduct the research for the sliding distance of rail clamp and the proper position of supporter with respect to the wedge angle in the wedge type rail clamp. The sliding distance to display the clamping force of the jaw pad corresponding to the design wind speed criteria is determined by the total displacement of the rail clamp at the roller center and the wedge angle. And the supporter is the device to prevent the overload which is applied on each part of the rail clamp by wind speed increment, because a clamping force is generated by the sliding of the wedge due to the wind. Accordingly the position of the supporter to prevent the overload is determined by analyzing the forces applied to the rail clamp. In order to analyze the sliding distance and the proper position of supporter with respect to the wedge angle as the wind speed is 40m/s, 5-kinds of wedge angles, such as 2, 4, 6, 8, $10^{\circ}$, were adopted as the design parameter.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1318-1321
• /
• 1997

A method for two-dimensional position measurement using an enclosing field has been studied and reported. The feature of this mehtod is zooming functional measurement by operating both the initial phase shift and the brightness ratio of the lighting function. An experimental system was developed and the experimental results on zooming effects are shown in this paper. This system is also an example of a "progressive learning measurement system".tem".uot;.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.244-249
• /
• 2002

It is known that tip clearance flows reduce the pressure rin, flow range and efficiency of the turbomachinery. So, the clear understanding about flow fields in the tip region is needed to efficiently design the turbomachinery. The Navier-Stokes code with the proper treatment of the boundary conditions has been developed to analyze the three-dimensional steady viscous flow fields in the transonic rotating blades and a numerical study has been conducted to investigate the detail flow physics in the tip region of transonic rotor, NASA Rotor 67. The computational results in the tip region of transonic rotors show the leakage vortices, leakage flow from pressure side to suction side and their interaction with a shock Depending on the operating conditions, the position of shock-wave on the blade surface are v8y different close to the blade tip of the transonic compressor rotor. The shock-wave position dose to the blade tip had the dose relationship with the starting position of leakage vortex and the direction of leakage flow.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.05a
• /
• pp.556-559
• /
• 2003

This paper presents a study on pull cord switch system which is employed in various industry for emergency stop of the equipments. In this paper, a new method for operation position detection of pull cord switch is suggested which is based on sensing operation position by detecting input resistance variation due to switching operation of pull cord switches with respective ohmic resisters. Moreover, this paper proposes a resistor circuit structure in order to improve recognition rates. Finally, this paper treats a system where such operating switches can be read by PLC.

• Journal of Biomedical Engineering Research
• /
• v.28 no.3
• /
• pp.363-368
• /
• 2007

Most surgery illumination systems have been developed as passive systems. However, sometimes it is inconvenient to relocate the position of the illumination system whenever the surgeon changes his pose. To cope with such a problem, this study develops an auto-illumination system that is autonomously tracking the surgeon's movement. A 5-DOF serial type manipulator system that can control (X, Y, Z, Yaw, Pitch) position and secure enough workspace is developed. Using 3 ultrasonic sensors, the surgeon's position and orientation could be located. The measured data aresent to the main control system so that the robot can be auto-tracking the target. Finally, performance of the developed auto-illuminating system was verified through a preliminary experiment in the operating room environment.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.461-465
• /
• 1996

Position and rate control modes arc the two common modes for controlling remote manipulators with joysticks or hand controllers. Generally, position mode is easier for teleoperation than rate modes, when the manipulation work space is small or comparable to the human operator's control space. When the telemanipulator's work space is very large, human operator's control motion range must be large to allow telemanipulator's full range of motion resulting poor control resolution. One way to solve the poor resolution problem is to use indexing. However, rate mode can provide any higher degree of resolution without use of indexing. If two modes are mixed, master controller will be more convenient. The mixed mode algorithm, changes operating mode from position mode to rate mode or vise versa using fuzzy logic. The fuzzy logic algorithm, which has been designed to recognize the teleoperator's intended motion properly, provides an intelligence to a master controller.