• Journal of the Korea institute for structural maintenance and inspection
• /
• 제24권5호
• /
• pp.45-52
• /
• 2020

An open-spandrel arch bridges, which consists of slab deck, arch rib, and vertical members, shows a various level of moment and axial forces according to the supporting boundary condition of arch rib and vehicle speeds. Also, the definition of impact factor accepts any kind of response parameters, not only displacement response at slab deck. The present study considers concrete open-spandrel arch bridges constrained with fixed conditions at the ends of arch rib and investigates the impact factor variation due to moving load speeds, response parameters, measuring locations, and vertical member spacing ratio of the bridges. The results of Reference model show that the impact factor is biggest when the reactive moment resulted at the vehicle-inducing opposite end of the arch rib is applied. The peak impact factor is a similar level obtained for the middle of the span adjacent to the slab deck center, but it is 19% higher than the peak impact factor calculated using the axial force developed at the same location. Reducing the spacing ratio of the vertical members as half as the reference model whose ratio is 1/9.375 produces a similar level of the moment-based peak impact factor compared to the reference model. However, when the spacing ratio is doubled, the peak impact factor is 4.4 times greater than the reference model.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제11권2호
• /
• pp.253-261
• /
• 1987

Thermoacoustic oscillation of an air column induced by heated wires is investigated analytically and experimentally. Acoustic power generation from a single heater wire is estimated based on the result of heat transfer analysis and expressed in terms of the efficiency factor indicating the conversion efficiency from heat to acoustic energy. It is shown that the efficiency factor becomes maximum when the wire radius is the order of the coustic boundary layer thickness and the flow velocity is close to the thermal diffusion velocity. Onset condition of the column oscillation is obtained by equating the acoustic power generation at the heater to the power loss due to thermoviscous dissipation at the tube wall and the convection and radiationloss at the open ends of the tube. In estimating the acoustic power generation, the heater is treated as a stretched single wire by correcting the flow velocity to take into account the interactions between adjacent heater wires. Experiment is performed by using a spiral heater of 1mm diameter in an air column of 37mm diameter. The heat input to drive the oscillation is measured and compared with the theoretical prediction. A good agreement is found between the theory and experiment, which is regarded as a substantial verification of the present analysis.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• 제31권4호
• /
• pp.199-208
• /
• 2019

Regular waves were generated in a wave flume under perfect reflection condition to evaluate performance of three CFD models of CADMAS-SURF, olaFlow, and KIOSTFOAM. The experiments and numerical simulations were carried out for three different conditions of non-breaking, breaking of standing waves, and breaking of incident waves. Among the three CFD models, KIOSTFOAM showed best performance in reproducing the experimental results. Although the run time was reduced by using CADMAS-SURF, its computational accuracy was worse than KIOSTFOAM. olaFlow was the fastest model, but active wave absorption at the wave generation boundary was not satisfactory. In addition, the model excessively dissipated wave energy when wave breaking occurred.

• Journal of the Korean Association of Geographic Information Studies
• /
• 제14권4호
• /
• pp.77-91
• /
• 2011

This study tries to find a streambed scouring and sedimentation characteristics through the Rosgen(1994)'s stream classification system while experiencing several flood events. The Jinwee and Osan streams, the tributaries of Anseongcheon were selected. The streams showed type C or type E. By the classification results, two Type C tributaries one Type C stream and one Type E tributary were selected. For the four selected stream reaches, the analysis of streambed change was implemented by using numerical model CCHE2D (Center for Computational Hydroscience and Engineering). To prepare the inlet boundary conditions of each stream, the WMS (Watershed Modeling System) HEC-1 was used and the streamflows of 50, 80, and 100-year return period were generated and the outlet boundary was set to an open boundary condition. The simulation results showed that when the flood pulse periodically the streambed changes also appears regularly. The results can be used to acquire the basic data for stream restoration.

• Journal of Korea Water Resources Association
• /
• 제49권7호
• /
• pp.635-644
• /
• 2016

This study investigates variation of flow characteristics due to variation of branch channel width and discharge ratio at bifurcation channel using 2D numerical model. The calculated result considering secondary flow is more accurate and stable than without considering one. The diversion flow rate ($Q_3/Q_1$) is reduced by flow stagnation effect according to the interaction of the secondary flow and flow separation zone in branch channel. The less upstream inflow or the lower upstream velocity, the bigger variation of diversion flow rate by changing branch channel width. At uniform downstream boundary condition, the rate of change in Froude number of downstream of main channel($Fr_2$)-diversion flow rate ($Q_3/Q_1$) relations is similar about -2.4843~-2.6675 when branch channel width ratio (b/B) is decreased. At uniform diversion flow rate ($Q_3/Q_1$) condition, the width of recirculation zone in branch channel is decreased when branch channel width ratio (b/B) is decreased. The less upstream inflow in the case of increasing branch channel width or the narrower branch channel width in the case of increasing upstream inflow, the bigger reduction ratio of recirculation zone width. At uniform inflow discharge ($Q_1$) condition, diversion flow rate, the width and length of recirculation zone in branch channel are decreased when branch channel width ratio (b/B) is decreased.

• Proceedings of KOSOMES biannual meeting
• /
• 해양환경안전학회 2006년도 추계학술발표회
• /
• pp.213-215
• /
• 2006

This study presents an application of GIS technologies to construct the graphic user interface for 3-dimensional exhibition of the results obtained by ocean hydrodynamic model. In coastal management studies, GIS provide a receptacle for scattered data from diverse sources and an improvement of the 3D visualization of such data. Within the frame of a GIS a variety of analytical, statistical and modeling tools can be applied to transform data and make them suitable for a given application. A 3D hydrodynamic model was driven by time-dependent external forcing such as tide, wind velocity, temperature, salinity, river discharge, and solar radiation under the open boundary condition. The Jinhae Bay was selected as a case study. Here, we have used GeoMania v2.5 GIS software and its 3D Analyst extension module to visualize hydrodynamic model result that were simulated around the Jinhae Bay.

• Journal of the Korean Society for Railway
• /
• 제13권1호
• /
• pp.44-50
• /
• 2010

This study is devoted to understand the basic characteristics of the flowfield around a train in evacuated tube and to suggest an efficient numerical method to calculate the flowfield. To get steady-state solution in minimum calculation domain, various boundary condition have been tried for steady calculation and have been compared to the solution of unsteady calculation. At the train velocity of 300km/h, the aerodynamic drag results of both calculation method agreed very well. The drag ratio between on the open filed and in the tube from the calculation result by the suggested numerical method lied in the same fitting curve with that from the filed test of high-speed trains running in the line.

• Journal of the Korean Association of Geographic Information Studies
• /
• 제7권3호
• /
• pp.99-107
• /
• 2004

This study presents an application of GIS technologies to construct the graphic user interface for 3-dimensional exhibition of the results obtained by ocean hydrodynamic model. In coastal management studies, GIS provide a receptacle for scattered data from diverse sources and an improvement of the 3D visualization of such data. Within the frame of a GIS a variety of analytical, statistical and modeling tools can be applied to transform data and make them suitable for a given application. A 3D hydrodynamic model was driven by time-dependent external forcing such as tide, wind velocity, temperature. salinity, river discharge, and solar radiation under the open boundary condition. The Jinhae bay was selected as a case study. Here, we have used GeoMania v2.5 GIS software and its 3D Analyst extension module to visualize hydrodynamic model result that were simulated around the Jinhae bay.

• 한국해양학회지
• /
• 제28권4호
• /
• pp.292-304
• /
• 1993

The east Sea circulation is numerically modeled with refined grid resolution elaborated open boundary condition, and by directly imposing the measured surface temperature and salinity typical the east Korean Warm current are clearer than those in previous works. among others, The Ulleung warm Water and the Intermediate Water of minimum salinity are nicely reproduced. The latter is formed in the northern/northwestern coastal region in winter and is advocated southward by strong under-current. the former is associated with a locally generated anti-cyclonic gyres. The model indicates strong seasonal variation of Nearshore Current along the Japanese coast from wintertime barotropic to summertime baroclinic structures. the associated strong reversed under-cur-rent in summer is not well understood. Global circulation pattern is characterized by two regions of cyclonic and anti-cyclonic gyres in the north and south, respectively. The presence of these gyres indicates importance of local dynamics in East Sea circulation. This model, however, does not completely resolve the problem of overshooting of the East Korean Warm current.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• 제19권6호
• /
• pp.883-888
• /
• 2010

This study have goal with conceptual design for Offshore Structures of high pressure control valve for localization. Ball valve for development accomplished with flow analysis based on provision of ANSI B16.34, ANSI B16.10, ANSI B16.25 In order to localize the Offshore Structures high pressure control valve. Numerical simulation using CFD (Computational Fluid Dynamic) in order to predict a mass flow rate and a flow coefficient form flow dynamic point of view. The working fluid assumed the glycerin (C3H8O3). The valve inlet and outlet setup a pressure boundary condition. The outlet pressure was fixed by atmospheric pressure and calculated until increasing 1bar to 10bar. CFD analysis used STAR-CCM+ which is commercial code and Governing equations were calculated by moving mesh which is rotated 90 degrees when ball valve operated opening and closing in 1 degree interval. The result shows change of mass flow rate according to opening and closing angle of valve, Flow decrease observed open valve that equal percentage flow paten which is general inclination of ball valve. Relation with flow and flow coefficient can not be proportional according to inlet pressure when compare with mass flow rate. Because flow coefficient have influence in flow and pressure difference. Namely, flow can be change even if it has same Cv value. The structural analysis used ANSYS which is a commercial code. Stress analysis result of internal pressure in valve showed lower than yield strength. This is expect to need more detail design and verification for stem and seat structure.