• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3D
• /
• pp.433-439
• /
• 2011

The frost depth(frost penetration) is used to install anti-frost heave layers in pavement designs. The freezing index is calculated by an annual accumulated value of multiplying the period of time with temperatures below zero, and the corresponding temperature. Therefore, the DAAT(daily average air temperature) calculation method may play an effect on the FI(freezing index). The Weather Observatory used to supply 4 average air temperatures per day, but currently supplies 8 per day. With this study, we divided the southern part(below FI=$350^{\circ}C{\cdot}day$) of the Korean peninsula into 6 areas according to site conditions(low embankment, embankment-cutting slope, and the cutting slope) and established a field measurement system for 15 positions to check the effects on the result of FI according to differing DAAT calculation methods. The air temperatures obtained by the field measurement system was used to calculate and compare the FI. As a result, the freezing index calculated based on the $DAAT_4(T_4)$ is normally greater by 3% than the one on $DAAT_8(T_8)$. In addition, the calibration equation for the freezing index using air temperatures was proposed through the research.

• Journal of the Korean Institute of Gas
• /
• v.20 no.4
• /
• pp.33-43
• /
• 2016

Grinding, weld deposition, type A sleeve, type B sleeve, composite sleeve, hot tapping and clamp are used as the method to repair the buried pipelines in the United States, UK and Europe. In the event of defect to the pipeline, they have repaired the pipeline through the fitness-for-service assessments. In addition, they have guidelines for the possible repair methods to apply to each type of damage, which is occurred due to the 3rd party construction or corrosion. According to the KGS FS551, Safety Validation in Detail including ECDA(External Corrosion Direct Assessment) as one method of integrity management should be carried out for the old pipeline which supply natural gas as the middle pressure in Korea. Where a defect on the pipelines is found, on the result of Safety Validation in Detail, the pipelines should be repaired or replaced by new piping. However, there are no guidelines or regulations regarding the repair and reinforcement of pipeline, so that, cutting the damaged pipeline and replacing it as a segment of new pipe is the only way in Korea until now. We have suggested pipeline repair methods including type A, B sleeve, composite sleeve, after the survey of foreign repair method and standards including the method of United States and the United Kingdom, and after analysis of the results on pipeline repair test including type A, type B sleeve and composite sleeve.

• Journal of the Korean Society of Costume
• /
• v.19
• /
• pp.105-125
• /
• 1992

The research, aiming an automatic pattern design of Korean Costume by utilizing CAD system, tried Grading, Seaming and Marking with a theme of girl's color-strip blouse & skirt. The content & conclusion of the research can be outlined as follows; 1) As we reviewed the current situation of Korean costume which becomes more likely celebrational or festival costume, while the demand of it is getting increase, it's being dealt mostly as ready-made dresses with different qualities & designs. Especially childrens ready-made ones were highly demanded to be picked up as the theme. 2) For the original drawing of children's color-strip blouse & skirt, Kyung-Ja Park's drawing method was used here, and for the substitute of particular body parts absolute size, Joo-Won Lee's standard size chart from a size-study by ages. 3) To work with CAD system we had input master pattern, drawn for age 5 as basic size, then graded six step-sizes for 1-11 years old. For add-subtract of particular body parts size, we graded through computing the standard variation among items to get the pattern developed into ready-made standard size, we can make precise plotting by grading wanted size very rapidly if we correct the rule of changed items different from standard size to make utilization possible enough with easy order method of ready-made Korean Dress. 4) We produced Marker after attaching a margin to seam accordingly by parts for each pattern using P/D/S to mark, In mass gament-cutting, the loss of time and material can minimized. In this research the apparel CAD system which has been utilized and only be western fashion industry was introduced for the design of ready-made Korean costume and utilized it in Grading, Marking which are critical steps to improve productivity and have reported the result in the research. Thus we expect that less cost, improved productivity and better quality with minimized loss of material from marking as well as from prompt and precise size-drawing. Furthermore the utilization of CAD system is considered as an effective one in terms of the research & the development to remove effective one in terms of the research & the development to remove irrational elements in the design and production process of Korean costume as well as in terms of the study of Korean Costume development through creative works of Korean Costume.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.55 no.4
• /
• pp.294-302
• /
• 2019

As a series of fundamental researches on the development of an automatic identification monitoring system for fishing gear. Firstly, the study on the installation method of automated identification buoy for the coastal improvement net fishing net with many loss problems on the west coast was carried out. Secondly, the study was conducted find out how to install an automatic identification buoy for coastal gill net which has the highest loss rate among the fisheries. GPS for fishing was used six times in the coastal waters around Seogwipo city in Jeju Island to determine the developmental status and underwater behavior to conduct a field survey. Next, a questionnaire was administered in parallel on the type of loss and the quantity and location of fishing gear to be developed and the water transmitter. In the field experiment, the data collection was possible from a minimum of 13 hours, ten minutes to a maximum of 20 hours and ten minutes using GPS, identifying the development status and underwater behavior of the coastal gillnet fishing gear. The result of the survey showed that the loss of coastal net fishing gear was in the following order: net (27.3%), full fishing gear (24.2%), buoys, and anchors (18.2%). The causes were active algae (50.0%), fish catches (33.3%) and natural disasters (12.5%). To solve this problem, the installation method is to attach one and two electronic buoys to top of each end of the fishing gear, and one underwater transmitter at both ends of the float line connected to the anchor. By identifying and managing abnormal conditions such as damage or loss of fishing gear due to external factors such as potent algae and cutting of fishing gear, loss of fishing gear can be reduced. If the lost fishing gear is found, it will be efficiently collected.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5B
• /
• pp.956-965
• /
• 2000

In this paper, we propose an efficient traffic grooming algorithm to minimize to number of SONET ADMs which is the dominant cost of system in high speed optical ring networks. It is an optimal traffic grooming algorithm to be applied to both unidirectional ring and bi-directional ring under both uniform traffic and nonuniform traffic. The proposed traffic grooming algorithm consists of two subalgorithms : one is the algorithm to construct full connection-rings as many as possible to minimize gaps by cutting the connections and using redirection method, and the other is the algorithm to groom connection-rings into a wavelength to maximize the number of shared nodes. The simulation results show that the proposed algorithm is superior to conventional algorithm under various network conditions.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2090-2100
• /
• 2011

Railway rail fastening system is the critical device which gives big influences to not only the vehicle driving stability and the orbit's structural stability against the impulsive load, but also the noise vibration and the ride comfort. As a part of the low-carbon green growth, the importance of the railroad industry is getting highlights on its excellent energy-efficiency and eco-friendliness. However, so far the Korea's domestic rail fastening system technology is not so good and the technical reliance to abroad is very heavy. In this study, we conducted comparative analysis on the rail fastening system with new and used one of the same type. And those systems are imported by Seoul Metro and are being used by it. With this basis, we developed the components and the materials and then, established the durability assessment methods appropriate to the Korean domestic circumstances. And through the reliability qualification test on the 7 parts of the rail fastening system, we've improved the reliability and guaranteed the 15 years of service lifetime. ($B_{10}Life15$) Establishment and standardization of Reliability Standard on the parts of the rail fastening system such as anti-vibration pads, guide-plate, screw spike made it possible to perform the internationally fair assessment. And it is thought that we can satisfy the manufactures' and consumers' needs of cost-cutting and qualification security by shortening of assessment period on rail fastening system.

• Journal of Educational Research in Mathematics
• /
• v.14 no.2
• /
• pp.171-185
• /
• 2004

Students are exposed to a concept of tangent from a specific context of the relation between a circle and straight lines at the 7th grade. This initial experience might cause epistemological obstacles regarding learning concepts of tangent to additional curves. The paper provides a method of how to introduce a series of concepts of tangent in order to lead students to revise and improve the concept of tangent which they have. As students have chance to reflect and revise a series of concepts of tangent step by step, they realize the facts that the properties such as 'meeting the curve at one point' and 'touching but not cutting the curve' may be regarded as the proper definition of tangent in some limited contexts but are not essential in more general contexts. And finally students can grasp and appreciate that concept of tangent as the limit of secants and the relation between tangent and derivative.

• Korean Journal of Human Ecology
• /
• v.18 no.3
• /
• pp.793-798
• /
• 2009

Hair cut is one of the best useful technical tool for hair styling. In this study using the rule of the layers of hair design, balanced for visual art, perceptual ability and form created by the principles of analysis and offer hair cuts and hair design of the representation of regions and even hair design as the basis of a student of Hair Beauty and all the people working in the field can create a variety of hair design puts the purpose to establish a basis. The result of this study can be outline as follows: First, the step line and the movement of the relationship between the law of the layers above and below the length of the same layer techniques, the same consists of a vertical cross-section of the overall round shape of the cut same layer is created and the appropriate volume and movement, the movement of low-layer round a little bit more feeling and expression is used when you want. High-layer used to want to move a lot of light and could see that. Second, the layer of the Law and over direction, lifting, section, the line control. weight control and analyzed by principle and the principle of the process of forming the written form was unknown. Third, hair design, the expansion of the expressive power of the law of the layers, and the section of the over direction depends on the presence of line control to express the length of the outline I had to, lifting the weight to adjust form controls, and the expression of Hair Design will be expanding the width. A hair designer, a layer style to create a zone he thought the law of the first layer formative area To further the reach will be a lot of research, leading up formative aspects of this research thesis do not have missing parts, or as a result of the Beauty of Hair Design and the width of a hair design education in the field can perform to help feed the reference materials that will be.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.12
• /
• pp.1702-1710
• /
• 2001

Supersonic coaxial jets are investigated numerically by using the axisymmetric, Wavier-Stokes equations which are solved using a fully implicit finite volume method. Three different kinds of coaxial nozzles are employed to understand the flow physics involved in the supersonic coaxial jets. Two convergent-divergent supersonic nozzles are designed to have the same Mach number 2.0, and used to compare the coaxial jet flows with those discharging from one constant-area nozzle. The impingement angle of the annular jets are varied. The primary pressure ratio is changed in the range from 2.0 to 10.0 and the assistant jet ratio from 1.0 to 3.0. The results obtained show that the fluctuations of the total pressure and Mach number along the jet axis are much higher in the constant-area nozzle than those in the convergent-divergent nozzles, and the constant-area nozzle lead to higher total pressure losses, compared with the convergent-divergent nozzles. The assistant jets from the annular nozzle affect the coaxial jet flows within the distance less than about ten times the nozzle throat diameter, but beyond it the coaxial jet is conical with self-similar velocity profiles. Increasing both the primary jet pressure ratio and the assistant jet pressure ratio produces a longer coaxial jet core.

• Korean Journal of Materials Research
• /
• v.23 no.1
• /
• pp.18-23
• /
• 2013

In this study, the effects of cryogenic treatment cycles on the residual stress and mechanical properties of 7075 aluminum alloy (Al7075) samples, in the form of a tube-shaped product with a diameter of 500 nm, were investigated. Samples were first subjected to solution treatment at $470^{\circ}C$, followed by cryogenic treatment and aging treatment. The residual stress and mechanical properties of the samples were systematically characterized. Residual stress was measured with a cutting method using strain gauges attached on the surface of the samples; in addition, tensile strength and Vickers hardness tests were performed. The detailed microstructure of the samples was investigated by transmission electron microscopy. Results showed that samples with 85 % relief in residual stress and 8% increase in tensile strength were achieved after undergoing three cycles of cryogenic treatments; this is in contrast to the samples processed by conventional solution treatment and natural aging (T4). The major reasons for the smaller residual stress and relatively high tensile strength for the samples fabricated by cryogenic treatment are the formation of very small-sized precipitates and the relaxation of residual stress during the low temperature process in uphill quenching. In addition, samples subjected to three cycles of cryogenic treatment demonstrated much lower residual stress than, and similar tensile strength compared to, those samples subjected to one cycle of cryogenic treatment or artificial aging treatment.