• 제어로봇시스템학회:학술대회논문집
• /
• 1999.10a
• /
• pp.153-156
• /
• 1999

The technique is reported of identifying parameters in off-line process. The technique demands that closed-loop system consists of a reference and two-degree-of-freedom controllers (TDFC) in real process. A model process is the same as the real process except their parameters. Deviations are differences between the reference and the output of the plant or the model. The technique is based on minimizing identification error between the two deviations. The parameter differences between the plant and the model are characterized of mean value and of variance which are derived from the identification error. Consequently, the algorithm which identifies the unknown plant parameters is shown by minimizing the mean value and the variance, respectively, within double convergence loops. The technique is applied to course change of a ship. The plant deviation at the first trial is shown to occur in replacing the nominal parameters by the default parameters. The plant deviation at the second trial is shown to not occur in replacing the nominal parameters by the identified parameters. Hence, the identification technique is confirmed to be feasible in the real field.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.724-729
• /
• 2007

In this paper, we propose a new diagnosis method of DC/DC converter aging. The method is based on variations of the parasitic resistor for the aging process. We apply an on-line diagnosis of the DC/DC converter because the observation is not a device, but a system. This study proposes a method of DC/DC converter diagnosis by analyzing the variations of model on the variations of parasitic resistor.

• Nuclear Engineering and Technology
• /
• v.36 no.5
• /
• pp.388-402
• /
• 2004

A phenomena identification and ranking table(PIRT) was developed for a main steam line break (MSLB) event for the Advanced Power Reactor-1400 (APR-1400). The selectee event was a double-ended steam line break at full power, with the reactor coolant pump running. The developmental panel selected the fuel performance as the primary safety criterion during the ranking process. The plant design data, the results of the APR-1400 safety analysis, and the results of an additional best-estimate analysis by the MARS computer code were used in the development of the PIRT. The period of the transient was composed of three phases: pre-trip, rapid cool-down, and safety injection. Based on the relative importance to the primary evaluation criterion, the ranking of each system, component, and phenomenon/process was performed for each time phase. Finally, the knowledge-level for each important process for certain components was ranked in terms of existing knowledge. The PIRT can be used as a guide for planning cost-effective experimental programs and for code development efforts, especially for the quantification of those processes and/or phenomena that are highly important, but not well understood.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.3
• /
• pp.42-51
• /
• 1999

An experimental modeling of cutting and structural dynamics and the on-line detection of malfunction process is substantial not only for the investigation of the static and dynamic characteristics of cutting process but also for the analytic realization of diagnostic systems. In this regard, We have discussed on the comparative assessment of two recursive time series modeling algorithms that can represent the machining process and detect the abnormal machining behaviors in precision round shape machining such as turning, drilling and boring in mold and die making. In this study, simulation and experimental work were performed to show the malfunctioned behaviors. For this purpose, two new recursive approach (REIVM, RLSM) were adopted fur the on-line system identification and monitoring of a machining process, we can apply these new algorithm in real process for the detection of abnormal machining behaviors such as chipping, chatter, wear and round shape lobe waviness.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.3
• /
• pp.131-136
• /
• 1990

In this paper, new methods are proposed which speed up the logical redundancy identification for the gate-level logic optimization. Redundancy indentification, as well as deterministic test pattern generation, can be viewed as a finite space search problem, of which execution time depends on the size of the search space. For the purpose of efficient search, we propose dynamic head line and mandatory assignment. Dynamic head lines are changed dynamically in the process of the redundancy identification. Mandatory assignement can avoid unnecessary assignment. They can reduce the search size efficiently. Especially they can be used even though the circuit is modified in the optimization procedure, that is different from the test pattern generation methods. Some experimental results are presented indicating that the proposed methods are faster than existing methods.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.1
• /
• pp.163-172
• /
• 1988

An off-line Geometric Adaptive Control Scheme is applied to the milling machine to identify its guideway errors. In the milling process, the workpiece fixed on the bed travels along the guideway while the tool and spindle system is fixed onto the machine. The scheme is based on the exponential smoothing of post-process measurements of relative machining errors due to the tool, workpiece and bed deflections. The guideway error identification system consists of a gap sensor, a, not necessarily accurate, straightedge, and the numerical control unit. Without a priori knowledge of the variations of the cutting parameters, the time-varying parameters are also estimated by an exponentially weighted recursive least squares method. Experimental results show that the guideway error is well identified within the range of RMS values of geometric error changes between machining passes disregarding the machining conditions.

• Asia Marketing Journal
• /
• v.9 no.3
• /
• pp.117-149
• /
• 2007

It can be explained by congruity theory as a process that consumers engage in a matching process to identify personal community that is congruent with their self-images to find the identification between the self and the personal community. Personal community cues that evoke certain images are viewed as activating similar beliefs about the self (e.g., high status). Individuals prompt a comparison process to determine whether the personal community and self-image are congruent and imagine prototypical users of the personal community and select ones that maximize similarity to their actual or desired self-concept. Identity is devided into personal identity and social identity. Consumers are likely to be influenced by both personal identity and social identity. In this article the influencing factors of the commitment to on-line personal community are explored by the sources of both personal identification and social identification. The results are as follows. The maintenance expression and enhancement expression of personal self influence the level of personal identification positively and the maintenance expression and enhancement expression of social self influence the level of social identification positively. The level of both social and personal identification positively influence the commitment to on-line personal community which gives positive responses to the source enterprise that allows the cyberspace and the other benefits to be used.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2451-2460
• /
• 2000

In order to minimize straightness error of deflected shaft, a geometric adaptive straightness controller system is studied. A multi-step straightening and a three-point bending process have been developed for the geometric adaptive straightness controller. Load-deflection relationship, on-line identification of variations of material properties, on-line springback prediction, and real-time hydraulic control methodology are studied for the three-point bending process. By deflection pattern analysis and fuzzy self-learning method in the multi-step straightening process, a straightening point and direction, desired permanent deflection and supporting condition are determined. An automatic straightening machine has been fabricated for rack bars by using the developed ideas. Validity of the proposed system is verified through experiments.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.1
• /
• pp.51-65
• /
• 2002

This paper presents a design method of the neural network-based controller using an indirect adaptive control method to deal with an intelligent control for chaotic nonlinear systems. The proposed control method includes the identification and control Process for chaotic nonlinear systems. The identification process for chaotic nonlinear systems is an off-line process which utilizes the serial-parallel structure of multilayer neural networks and simple state space neural networks. The control process is an on-line process which uses the trained neural networks as the system model. An error back-propagation method was used for training of identification and control for chaotic nonlinear systems. The performance of the proposed neural network controller was evaluated by application to the Duffing equation and the Lorenz equation, and the proposed controller was compared with other neural network-based controllers by computer simulations.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.5
• /
• pp.46-52
• /
• 2003

In this work we developed the closed-loop model of a paper machine during grade change with the intention to provide a reliable dynamic model to be used in the model-based grade change control scheme. During the grade change, chemical and physical characteristics of paper process change with time. It is very difficult to represent these characteristics on-line by using physical process models. In this work, the wet circulation part and the drying section were considered as a single process and closed-loop identification technique was used to develop the grade change model. Comparison of the results of numerical simulations with mill operation data demonstrates the effectiveness of the model identified.