• 대한전기학회논문지
• /
• 제43권4호
• /
• pp.594-600
• /
• 1994

The maximum charge accumulation in transformers caused by streaming electrification is commonly observed on the bottom area of transformer winding(i.e.the oil inlet of transformer winding). It is because turbulent flows occur in this portion of transformers. Consequently, if we are to reduce the maximum charge accumulation of transformers, it is important that we should have a good understanding of the conditions of the occurence of partial turbulent flows in the oil inlet of transformer winding. With this point in mind, a simple flow model was designed in this study in order to simulate oil flow in the insulation ducts of power transformers. As a method for mitigating charge accummulation, attention was given to (a) a flow path design for the improvement of flow conditions, and (b) the charge tendency of the material used this design. The results of this study show that the above method is useful for mitigating charge accumulation.

• 대한기계학회논문집
• /
• 제7권4호
• /
• pp.469-476
• /
• 1983

The effects of oil supply conditions on the static and dynamic properties of journal bearings supporting high speed rotors were investigated. The initially unknown hydrostatic pressure in oil pockets were determined by iteration with the aid of the equation of oil flow balance for given oil supply pressure and flow coefficients of oil inlet. For the calculation of dynamic characteristics, the dynamic changes of pressure in lubricating gaps and oil pockets were linearised with a perturbation method.

• 한국정밀공학회지
• /
• 제21권2호
• /
• pp.108-115
• /
• 2004

Experiment and analytical studies on the oil supply characteristics of scroll compressor have been presented. For a scroll compressor, oil supply system consisting of individual lubricating element such as pumps, oil passages and sliding surfaces has been modeled by equivalent electric circuit. By solving the closed network equations of the model, oil flow rates at various lubrication elements could be obtained. Total amount of the oil flow rate drawn into the shaft has been measured and compared reasonably well with the prediction by the numerical simulation.

• Tribology and Lubricants
• /
• 제20권3호
• /
• pp.119-124
• /
• 2004

Engine bearing system is generally affected by aeration. In this paper, the aeration effects on the engine crankshaft bearing system were studied. To do this, unsteady oil flow analysis on the engine crankshaft oil circuit system was carried out. And aeration effects on the bearing system were simulated to figure out lubrication characteristics of the each bearing such as oil flow rate, minimum oil film thickness, friction loss and increase of oil temperature.

• 대한전기학회논문지
• /
• 제39권6호
• /
• pp.568-576
• /
• 1990

Recently, streaming electrification in forced oil cooled power transformer has been taken up as a serious problem. In this paper, the charging tendency of various insulation oils, such as mineral oil, polybutene and silicone oil has been measured by means of an injection type charging tendency measuring apparatus under various condition. The experimental data of the dependence of the leakage current on flow velocity and temperature of oil can be explained by considering the flow state such as laminar and turbulent flow. The effect of additives on the charging tendency of mineral oil has been investigated. BTA is regarded as the most effective retardant to electrification of oil among the additives chose for this investigation.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제22권6호
• /
• pp.48-56
• /
• 2017

Although various methods have been investigated for treatment of crude oil contaminated soil, more researches are still required to preserve soil environment. This study investigated the potential utility of subcritical water in remediation of crude oil contaminated soil under various experimental conditions including temperature ($150-300^{\circ}C$), flow rate (1.0-2.0 mL/min) and extraction time (60-120 min). The removal rate of crude oil gradually increased with increasing temperature and time. After treatment at $200^{\circ}C$ and $300^{\circ}C$ for 60 min, the remaining concentration of crude oil met the Kuwait standard clean-up level (10,000 mg/kg) and the Korean standard level (2,000 mg/kg), respectively. The removal efficiency of crude oil increased from 77.8% to 88.4% with increasing extraction time from 60 to 120 min at $250^{\circ}C$. A decreasing rate of oil removal was observed as flow rate increased, possibly due to channeling flow occurred within the soil body at higher flow rate condition. Overall, the results revealed that subcritical water extraction process could be feasible for remediation of crude oil contaminated soil, and the relative effect of parameters on the oil removal was in the order of temperature > time > flow rate.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1251-1256
• /
• 2014

The use of lubrication oil is of many purposes and one among them is to drive the engine mounted on a ship. Hence the supply of clean lubrication oil is important. And an oil purifier is one of key components in marine diesel engines. At present, the element type full-flow oil filter has been widely used for cleaning the engine oil. The self-driven centrifugal oil purifier is a device which is used to remove the impurities in lubrication oil using a jet flow. The flow characteristics and the physical behaviors of particles in this self-driven oil purifier were investigated numerically and the filtration efficiencies were evaluated. For calculations, a Computational Fluid Dynamics method is used and the Shear Stress Transport turbulence model has been adopted. The Multi Frames of Reference method is used to consider the rotating effect of the flows. The influence of centrifugal forcehas been numerically investigatedto improve filtration efficiency of tiny particles. As a result of this research, it was found that the particle filtration efficiency using the only center axis rotating and outer wall rotating system are higher than that of the fully rotating system in the self-driven oil purifier.

• 한국가구학회지
• /
• 제18권4호
• /
• pp.307-311
• /
• 2007

An experiment was conducted to know the essential oil penetration depth in radial and longitudinal direction of Prunus sargentii. Oil penetration depth was found greater than radial flow depth. Vessel conducted oil more than wood fiber. In radial direction, body ray parenchyma was found more permeable than marginal ray parenchyma and it was about 138% times higher. Furthermore penetration depth of oil in intercellular space was greater than ray parenchyma and it was about 250% higher than ray parenchymas. Initial flow speed was found high and then it gradually decreased.

• 한국자동차공학회논문집
• /
• 제16권2호
• /
• pp.1-7
• /
• 2008

In order to enhance the performance of an automotive engine, many researchers have been carried out. An oil jet cooling a piston is one of important parts for engine performance. Therefore, the efficient cooling system of an oil jet is needed. In this paper, unsteady flow analysis of the oil jet which consists of a check valve and a nozzle has been accomplished. And the reaction between mass flow rate and ball movement was also investigated.

• Korean Chemical Engineering Research
• /
• 제57권6호
• /
• pp.883-890
• /
• 2019

Two-phase flow near the wellbore in volatile oil reservoirs causes complications in well test analysis. In this study, the flow behavior of volatile oil reservoirs below the bubble-point pressure and the potential of radial composite model for interpretation of two-phase well test in volatile oil reservoirs was investigated. A radial composite model was used for two-phase well test analysis. A new procedure was developed to interpret well test data and estimate the radius of the two-phase region. The changes in fluid composition near the wellbore during drawdown test were found to increase the saturation pressure, which affects the saturation profile during build-up. Well test results showed that the radial composite method is a powerful tool for well test characterization and estimation of reservoir parameters. The proposed procedure was able to estimate the reservoir parameters and radius of the two-phase region with acceptable accuracy.