• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.9
• /
• pp.822-829
• /
• 2015

In this paper, the piezoelectric-hydraulic pump with a piezostack actuator as a driving source has been designed, fabricated, and evaluated for its application to UAV's brake system. The performance requirements of the piezoelectric-hydraulic pump were decided based on the requirements analysis of the target aircraft brake system. The geometric design of the piezoelectric-hydraulic pump to meet the performance requirements of the pump was conducted, and all components of the pump including the spring sheet type check valves were machined with close tolerance. By constructing a test apparatus for the performance check of the piezoelectric-hydraulic pump, the performance characteristics of the pump, such as the outlet flow rate for load-free condition and the outlet oil pressure for closed loop condition, have been evaluated. It has been found by the performance test result that the developed piezoelectric-hydraulic pump satisfies the design requirements effectively.

• Journal of Energy Engineering
• /
• v.24 no.4
• /
• pp.124-129
• /
• 2015

An experimental study was performed estimating COP(Coefficient of Performance) of air-conditioning cycle using inverter scroll compressor with and without $Al_2O_3$ nano particle. All experiments were done for various compressor speeds from 1000~4000 rpm and used the inverter controller called CANDY to change the compressor rpm. The air-conditioning cycle components in the apparatus were used as same with components of YF hybrid car. To estimate the COP, this study measured the temperature and pressure at inlets and outlets of compressor, condenser, and evaporator. And also measured the compressor input power using Powermeter. Through the experiments, the maximum error to estimate COP was shown about ${\pm}6.09%$ at 3500rpm. The COP of refrigeration cycle with $Al_2O_3$ nano-particle was similar with that of the base cycle without nano-particle between 1000~3000 rpm of the compressor speed. But, This study showed that the COP of the cycle with $Al_2O_3$ over 3000 rpm of the compressor speed was higher than that of the base cycle due to the higher heat transfer rate increased in the evaporator from the higher oil flow rate inside the cycle as well known. Those results can be used the basic and fundamental data to design the air-conditioning cycle using inverter scroll compressor with $Al_2O_3$ nano particle.

• Korean Journal of Food Science and Technology
• /
• v.36 no.2
• /
• pp.276-282
• /
• 2004

Barley flakes were developed by extrusion cooking using broken kernels, by-products of the barley pearling process. Broken kernels from both non-waxy and waxy barley broken kernels were sufficiently gelatinized at the barrel temperature of over $100^{\circ}C$ and the moisture content of broken kernels of over 35%. Cutting and flaking roll separating properties of pellets prepared from non-waxy barley broken kernels were better than those of waxy barley broken kernels. Characteristics of pellets prepared by extrusion cooking in different mixing ratios of non-waxy and waxy barley broken kernels were investigated. As the mixing ratio of waxy barley broken kernels increased, RVA peak viscosity, apparent viscosity, and yield stress of prepared pellets decreased, while flow behavior index increased. As the mixing ratio of waxy barley broken kernels increased, compressive strength and bulk density of deep-fat fried flakes drastically decreased, and the size of air cells on cross-section increased, and thickness of cell-constituting bodies decreased. Sensory evaluation results showed that acceptability for texture and taste of flakes inclosed as the mixing ratio of waxy barley broken kernels increased, and optimum mixing level of waxy barley broken kernels appeared to be 30-40%.

• Journal of Korean Foot and Ankle Society
• /
• v.18 no.3
• /
• pp.100-107
• /
• 2014

Purpose: The purpose of this study is to evaluate the efficacy of mesenchymal stem cell (MSC) isolation by the magnetic-activated cell sorting (MACS) method in tendon tissue-derived cells compared to the colony picking method for isolation of MSCs by picking colony-forming cells. Materials and Methods: Human tendon-derived cells were isolated by enzyme digestion using normal tendon tissues from three donors. We used the magnetic kit and well-known MSC markers (CD90 or CD105) to isolate MSCs in tendon-derived cells using MACS. Cloning cylinders were used to isolate colony-forming cells having MSC characteristics in tendon-derived cells. Colony-forming unit-fibroblast (CFU-F) assay was used to evaluate the self-renewal capacity of cells isolated using the colony picking method or MACS. For comparison of differentiation potentials into osteogenic or adipogenic lineage between two groups, alizarin red S and oil red O staining were performed at 14 days after induction of differentiation in vitro. Results: Flow cytometry results showed that early passage tendon-derived cells expressed CD44 in 99.13%, CD90 in 56.51%, and CD105 in 86.19%. In the CFU-F assay, CD90+ or CD105+ cells isolated with MACS showed larger colony formation in size than cells isolated using the colony picking method. We also observed that CD90+ or CD105+ cells were constantly differentiated into both osteogenic and adipogenic lineages in cells from all donors, whereas cells isolated using the colony picking method were heterogeneous in differentiation potentials to the osteogenic and adipogenic lineages. Conclusion: CD90+ or CD105+ cells isolated using MACS showed superior MSC characteristics in the self-renewal and multi-differentiation capacities compared with cells isolated using the colony picking method.

• Korean Chemical Engineering Research
• /
• v.45 no.3
• /
• pp.249-257
• /
• 2007

The periodic square wave (PSW) model was successfully applied to the optimal design of a batch-storage network. The network structure can cover any type of batch production, distribution and inventory system, including recycle streams. Here we extend the coverage of the PSW model to multitasking semi-continuous processes as well as pure continuous and batch processes. In previous solutions obtained using the PSW model, the feedstock composition and product yield were treated as known constants. This constraint is relaxed in the present work, which treats the feedstock composition and product yield as free variables to be optimized. This modification makes it possible to deal with the pooling problem commonly encountered in oil refinery processes. Despite the greater complexity that arises when the feedstock composition and product yield are free variables, the PSW model still gives analytic lot sizing equations. The ability of the proposed method to determine the optimal plant design is demonstrated through the example of a high density polyethylene (HDPE) plant. Based on the analytical optimality results, we propose a practical process optimality measure that can be used for any kind of process. This measure facilitates direct comparison of the performance of multiple processes, and hence is a useful tool for diagnosing the status of process systems. The result that the cost of a process is proportional to the square root of average flow rate is similar to the well-known six-tenths factor rule in plant design.

• Journal of Biosystems Engineering
• /
• v.25 no.3
• /
• pp.221-226
• /
• 2000

Hot air heater with light oil burner is the most common heater for greenhouse heating in the winter season in Korea. However, since the thermal efficiency of the heater is about 80∼85%, considerable unused heat amount in the form of exhaust gas heat discharges to atmosphere. In order to capture this exhaust heat a heat recovery system for plant bed heating in the greenhouse was built and tested in the hot air heating system of greenhouse. The heat recovery system is made for plant bed or soil heating in the greenhouse. The system consisted of a heat exchanger made of copper pipes, ${\Phi}12.7{\times}0.7t$ located in the rectangular column of $330{\times}330{\times}900mm$, a water circulation pump, circulation plastic pipe and a water tank. The total heat exchanger area is 1.5$m^2$, calculated considering the heat exchange amount between flue gas and water circulated in the copper pipes. The system was attached to the exhaust gas path. The heat recovery system was designed as to even recapture the latent heat of flue gas when exposing to low temperature water in the heat exchanger. According to the performance test it could recover 45,200 to 51,000kJ/hr depending on the water circulation rates of 330 to $690\ell$/hr from the waste heat discharged. The exhaust gas temperature left the heat exchanger dropped to $100^{\circ}C$ from $270^{\circ}C$ by the heat exchange between the water and the flue gas, while water gained the difference and temperature increased to $38^{\circ}C$ from $21^{\circ}C$ at the water flow rate of $690\ell$/hr. By the feasibility test conducted in the greenhouse, the system did not encounter any difficulty in operations. And, the system could recover 220,235kJ of exhaust gas heat in a day, which is equivalent of 34% of the fuel consumption by the water boiler for plant bed heating of 0.2ha in the greenhouse.

• Journal of the Korean Institute of Gas
• /
• v.6 no.1 s.17
• /
• pp.38-45
• /
• 2002

Hydrates are solid cryctallines resembling ice in appearance, which are consist of a gas molecule surrounded by a cage of water molecules. Because of containning a large amount of methane, hydrates have been considered as a future energy resource. However, the formation of hydrates in the oil and gas industries has been known as a serious problem for a long time. The formation of hydrate in pipeline is common in seasonally cold or sub-sea environments with low temperatures and high pressures. Especially, hydrate plug formation becomes a real menace to flow assurance in inadequately protected transmission lines. This study was carried out for the purpose of understanding mechanism of hydrate plugging and examining formation conditions of hydrate in high pressure gas pipeline. In this study, we measured hydrate equilibrium conditions under the various flowing conditions with the methane. The results were presented both the plugging tendency and the effect of flowing velocity.

• Journal of the Korean Society of Groundwater Environment
• /
• v.6 no.3
• /
• pp.152-157
• /
• 1999

Oil leaked from underwound storage tanks and leachate from sanitary landfills have been known as contaminant sources of the high-quality groundwater resources. The mobility of contaminants in the aquifer largely depends on the groundwater flow and the determination of associated hydraulic parameters is essential for a proper remediation of contaminated grnundwater. This study aimed at determining an optimum set of hydraulic parameters for an unconfined sandy aquifer of a laboratory scale through comparison of various methods. Results showed that the specific yield obtained from gravity drainage experiment was an average of 0.20 with minor variations in aquifer depths. and the permeabilities obtained from Dupuit approximation and slug test gave similar values of 5.33 cm/min and 5.85 cm/min but the constant head method gave 0.17 cm/min, which is much ion than the other methods. This experimental evidence reveals that the permeability of the unconfined sandy aquifer could be accurately determined by Dupuit assumption or slug tut rather than by constant head method conducted for a disturbed separate soil column.

• Korean Journal of Food Science and Technology
• /
• v.46 no.3
• /
• pp.315-322
• /
• 2014

Immobilized lipases were prepared by physical adsorption using lipase AK, AY, AH, PS and R on Amberlite$^{(R)}$XAD$^{(R)}$7 HP resin. With the immobilized lipases (10%), structured lipid was synthesized by enzymatic interesterification of canola oil, palmitic ethyl ester, and stearic ethyl ester in order to study the reaction characteristics. Among the lipase, the highest protein content was obtained from lipase AH (11.41%) before immobilization, while the highest levels of bound protein was observed from immobilized lipase AK (63.91%). Immobilized lipase AK had the highest interesterification activity (38.3% of total saturated fatty acid). Lipase AK was also used for a continuous reaction in which the slow flow of reactant resulted in increased reaction rate. Reusability of immobilized AK, AH and PS increased at the second reaction (120-196.5%). However, the activity of immobilized AK, which had the highest bound protein content (63.91%) decreased after the third reaction, while the activity of immobilized AH and PS was maintained until the sixth reaction.

• Proceedings of the KOR-KST Conference
• /
• 2001.02a
• /
• pp.3-29
• /
• 2001

본 연구에서는 기존의 대중교통 통행배정모형이 고려하지 않거나 미흡하게 반영하였던 차량과 노선의 용량제약을 고려한 모형의 구축을 시도하였다. 일반적으로 대중교통 통행배정에서 수요와 공급의 관계는 수요가 증가하는 것과 무관하다고 받아들여지고 있으나 용량 초과는 통행자들의 경로선택 및 수단선택에 영향을 끼친다고 볼 수 있다. 이러한 용량초과에 의한 혼잡을 반영하기 위해 용량제약식을 포함한 모형을 개발하고 실용운행회수라는 개념을 도입하였다. 또한 기존에 제시된 용량제약을 고려한 모형들이 실제적인 현상을 정확히 모사하는 데에는 한계가 있을 뿐 만 아니라 현실과 다소 거리가 있는 가정이 내재되어 있는 반면 본 연구에서는 가능한 한 최대로 현실 여건을 반영하는 모형을 정립하였다. 본 연구에서 제시한 모형은 동일한 기종점 사이를 운행하는 경쟁노선이 많은 대도시에서 통근·통학을 위한 통행자들이 많은 오전, 오후 첨두시 대중교통 수요를 분석하여 대중교통의 운행관리체계 개선 및 투자계획, 서비스 개선을 위한 수요예측을 하는데 유용하게 사용할 수 있을 것으로 사료된다. 그리고 기존의 대중교통 통행배정의 결과가 현재나 장래의 잠재적인 수요(demand)를 예측하는 방법인데 반하여 본 연구에서 정립된 모형은 주어진 네트워크에서 실제로 통행하고 있는 수요(flow)를 예측함으로써 교통 계획가나 대중교통 운영자의 계획 및 운영정책수립에 합리적인 도움을 줄 수 있다. 또한 현재의 대중교통 시스템 하에서의 통행배정 뿐만 아니라 다른 형태의 용량과 운행특성을 가진 교통 수단이나 노선이 도입되었을 때 공급이 제한적인 경우의 수요 예측에 적합한 모형을 개발하였다.에 대한 규제가 초국가적 차원으로 발전되는 계기를 제공하고 있다. 향후, 담배규제협약안의 세부사안들에 대한 합의과정에서 각 국별로 상당한 이견과 반발이 예상되고 있지만, 협약안의 전체 회원국 투표에서 승인될 경우 각 국가들뿐만 아니라 담배산업과 담배기업들에게 미치는 파급효과가 매우 클 것으로 예상된다. 대부분의 국제협약들이 그러하듯이, 담배규제협약도 그 적용 범위와 수준이 어느 정도로 결정되는지에 따라 각 국가와 기업별 이해관계가 크게 달라지게 되기 때문에 신중한 대응전략이 요구된다고 하겠다.의 화물전용차선의 설치시는 수답렬 교통량의 구성비와 구간 평균교통량에 의하여 그 효과가 다르게 나타남을 알 수 있었다. 따라서 물류비용 절감차원에서의 화물전용차선의 설치는 본 연구에서 나타낸 방법과 같이 수단간의 경제적 편익을 고려한 구간별 시간대별 효과분석을 통하여 정책의 시행여부가 결정되어야 할 것이다. 한편, 화물전용차선의 설치로 인한 물류비용의 절감을 보다 효과적으로 달성하기 위해서는 종합류류 전산망의 시급한 구축과 함께 화물차의 적재율을 높이고 공차율을 낮출 수 있는 운송체계의 수립이 필요한 것으로 판단된다. 그라나 이러한 화물전용차선의 효과는 단기적인 치유책일 수밖에 없기 때문에 물류유통 시설의 확충을 위한 사회간접자본의 구축을 서둘러 시행하여야 할 것이다.으로 처리한 Machine oil, Phenthoate EC 및 Trichlorfon WP는 비교적 약효가 낮았다.>$^{\circ}$E/$\leq$30$^{\circ}$NW 단열군이 연구지역 내에서 지하수 유동성이 가장 높은 단열군