• Journal of the Korean Applied Science and Technology
• /
• v.34 no.2
• /
• pp.327-337
• /
• 2017

A continuous low temperature ($510^{\circ}C{\sim}530^{\circ}C$) pyrolysis experiment in a pilot-scale of 85.3 kg/hr was carried out by the mixed feedstock of half dried digested sewage sludge and waste plastics. As a result, the amount of pyrolysis gas generated was maximum 68.3% of input dry mass and scored $40.9MJ/Nm^3$ of lower heating value (LHV), and the percentage of air inflow caused by continuous pyrolysis was 19.6%. The oil was produced 4.2% of the input dry mass, and the LHV was 32.5 MJ/kg. The sulfur and chlorine contents, which could cause corrosion of the facility, were found to be 0.2% or more respectively. The carbide generated was 27.5% of the input dry mass which shows LHV of 10.2 MJ/kg, and did not fall under designated waste from the elution test. The concentration of carbon monoxide, sulfur oxides and hydrogen cyanide of emitted flu gas from pyrolysis gas combustion was especially high, and dioxin (PCDDs/DFs) was within the legal standards as $0.034ng-TEQ/Sm^3$. Among the 47 water pollutant contents of waste water generated from dry flue gas condensation, several contents such as total nitrogen, n-H extract and cyanide showed high concentration. Therefore, the merge treatment in the sewage treatment plants after pre-treatment could be considered.

• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.299-307
• /
• 1996

The surface tension of PO added sodium poly(oxyethylene(EO), oxyisopropylene(PO)) dodecyl ether sulfate firstly were slightly lower than EO added sulfate in the concentration range of $10^{-6}{\sim}10^{-3}mol/{\ell}$. And they had lower critical micelle concentration ($10^{-4}{\sim}9{\times}10^{-5}mol/{\ell}$) than general anionic surfactants. The adsorptivity ($2.2{\times}10^{-10}mol/cm^2$) of sodium $(PO)_{10}(EO)_5$ dodecyl ether(compound of PO addition firstly) calculated by Gibbs' adsorption isotherm were higher than that of sodium $(EO)_{10}(PO)_5$, dodecyl ether(compound of EO addition firstly), but were lower than that of sodium dodecyl sulfate (${\Gamma}=3.2{\times}10^{-10}mol/cm^2$). These could be understood that the adsorption areas of compounds were very large because of their high molecular weight. Moreover, PO compounds showed better properties than EO compounds in foamability, emulsifying power for organics (n-hexane, benzene), detergency for the lard, tallow oil mixture and dispersability for iron oxide. It was interpreted in terms of surface properties of the PO compounds. These showed that the interfacial activity become higher when hydrophilic and hydrophobic portion existed in aggoromerated state respectively. The test results of emulsifying power for organics (n-hexane, benzene) showed better for benzene than n-hexane. Eight kinds of sodium (EO, PO) dodecyl ether derivatives showed irregular dispersibilities for polar iron oxide in water dispersed media.

• Journal of the Korean Chemical Society
• /
• v.47 no.5
• /
• pp.479-486
• /
• 2003

In this study, poly(DL-lactide-co-glycolide) nanoparticles loaded with water-insoluble vitamins such as vitamin A (Retinol) and vitamin E acetate were prepared by the emulsification diffusion method. Polymer solution was prepared by the two water-miscible organic solvent, such as ethanol and acetone. Because of its biocompatible property, polyethyleneglycol-polypropyleneglycol diblock copolymer was used as surfactant and stabilizer. The influence of some preparative variables on the nanoparticle formation and on the loading efficiency of active agents, such as the type and concentration of stabilizing agent, the stirring methods, the water/oil phase ratio and the polymer concentration were investigated in order to control and optimize the process. After preparation of nanoparticles loaded with active agent, particle size and distribution were evaluated by the light scattering particle analyzer. The loading efficiency of active agents was evaluated by the UV-visible spectroscopy. As the results, particle size were 50-200 nm and dispersibility was monodisperse. The optimum loading efficiency of active agents was observed 50-60%. It was found that the appropriate of selections of binary solvent mixtures and polymeric concentrations in both organic and aqueous phases could provide good yield and favorable physical properties of PLGA nanoparticles.

• Korean Journal of Clinical Pharmacy
• /
• v.21 no.3
• /
• pp.256-269
• /
• 2011

Omega-3 fatty acids are a specific type of unsaturated fat that the body cannot manufacture on its own, so they must be obtained from food which is essential fatty acids (EFAs). Omega-3 fatty acids consist of three types which are a-Linolenic Acid (ALA), Eicosapentaenoic (ELA), and Docosahexaenoic Acid (DHA). Especially, EFAs help to prevent skin and hair drying, acne, eczema, prevention from allergies, brittle nails, rashes, and tiny lumps. The aim of this study is to investigate improvement and protection for hair damaged by chemical treatment with omega-3 formulated shampoo. We selected virgin hair sample and divided into two groups for bleaching once and three times and then damaged hair by changing the number of hair bleaching (twice with interval of 15 minutes). Each bleached hair was treated by five different kinds of shampoo (Control, Horse shampoo, DHA shampoo, EPA shampoo, Omega-3 shampoo mixture). Apart from this, EPA/DHA 2, 5, 8, 10 and 12% shampoo were prepared and treated to hair for comparing rate of progress in damaged hair. To quantify improved condition of damaged hair, we performed Scanning Electron Microscope (SEM) for ultrastructure of damaged hair fraction, measurement of thickness change and BCA Protein Assay for recovery rate of damaged hair. The moisture in hair was measured by Thermal analysis machine. In results, we observed the particle of hair surface damaged by bleaching treatment were well improved with treatment with EPA and DHA shampoo. Also, quantity of protein was lowered with higher concentration of EPA & DHA i.e., 8 and 12 % then compared with horse oil shampoo in three times treatment group. It shows that bleached hair have been recovered by treating rapidly and get protective coat. In conclusion, EPA and DHA shampoo improved damaged hair, especially with EPA / DHA 12% shampoo. Also, EPA shampoo could protect the damaged hair depending on increasing concentration of EPA. Therefore, we conclude omega-3 shampoo could make damaged hair protect and get healthy hair environment.

• Journal of Energy Engineering
• /
• v.11 no.2
• /
• pp.114-121
• /
• 2002

Alkali metal compounds existed in original coal or sorbents are exhausted as vapor or small particle at the outlet of combustor when operating PFBC power plant. These compounds can be removed with dust removal equipment, but total generation efficiency will be decreased because of lower operating temperature of dust removal equipment. Alkali metal contained in vapor phase is initially deposited onto turbine blade results in serious corrosion. The concentration of alkali vapor in the PFBC flue gas is 20∼40 ppm which is dependent on mineral characteristics and composition as well as operating condition of PFBC. However, the allowance limit of alkali metal vapor is assigned as less than 50 ppb for gas turbine when coal or oil is used as fuel. Therefore, alkali metal vapor in PFBC or IGCC process should be removed by solid sorbents to prevent corrosion of turbine blade and improve plant efficiency. In the present investigation, powder of Bauxite, Kaolinite and Limestone is used in the preparation of cylinder-type pellet which is inserted into the pressurized alkali removal reactor for the alkali absorption experiment. Experimental results showed that the alkali removal efficiency in the order of Bauxite, Kaolinite and Limestone. Alkali vapor removal efficiency is related with reaction temperature, porosity of pellet and alkali vapor concentration of flue gas.

• Journal of Soil and Groundwater Environment
• /
• v.23 no.5
• /
• pp.26-36
• /
• 2018

Total petroleum hydrocarbon (TPH) is a mixture of various oil substances composed of alkane, alkene, cycloalkane, and aromatic hydrocarbons (benzene, toluene, ethylbenzene, xylene, etc.). In this study, we investigated 92 groundwater wells around 36 gas stations to evaluate distribution characteristics of petroleum hydrocarbons. Groundwater in the wells was sampled and monitored twice a year. The fraction analysis method of TPH was developed based on TNRCC 1006. The test results indicated aliphatic and aromatic fractions accounted for 28.6 and 73.8%, respectively. The detection frequencies of TPH in the monitoring wells ranged in 21.6 - 24.2%. The average concentration of TPH was 0.11 mg/L with the concentration range of 0.25~0.99 mg/L. In the result of TPH fraction analysis, in aliphatic fractions were 19% (C6-C8 : 0.2%, C8-C10 : 0.4%, C10-C12 : 0.4%, C12-C16 : 0.5%, C16-C22 : 1.0%, C22-C36 : 16.6%), and aromatic fractions were 81% (C6-C8 : 1.1%, C8-C10 : 0%, C10-C12 : 2.9%, C12-C16 : 0.3%, C16-C22 : 4%, C22-C36 : 66.8%). Fractions of C22-C36 were detected in about 83% of the monitoring wells, suggesting non-degradable characteristics of hydrocarbons with high carbon content.

• Journal of Nutrition and Health
• /
• v.17 no.4
• /
• pp.253-261
• /
• 1984

The effect of fiber sources on lipid metabolism was investigated in relation to the level of dietary fat. After rats were fed each diet for 4 weeks, all animals were sacrificed to collect the liver, and blood samples by heart puncture. Total lipid, total cholesterol, phospholipid and HDL- cholesterol were determined in serum. Total lipid and total cholesterol were also determined in liver. These results were compared with the histochemical appearances by the method of Oil red-O staining. Higher level of fat in the diet appeared to increase the total lipid levels in serum and more fat in the liver cells were shown from the high fat diet judging from the E.M. pictures. Phospholipid concentration in serum was greater in the rats of high fat groups than those of the control or non-fat groups. High fat level caused to decrease the HDL- cholesterol concentration in serum. Pectin decreased serum and liver lipids and the deposit of fat in the liver cells. HDL-cholesterol levels in serum was increased by pectin. Whereas the cellulose supplementation had no effect to reduce serum and liver total lipid levels, and cellulose did not decreased the deposit of fat in the liver cells. From these results, it is concluded that dietary fat levels led to changes in the lipid metabolism of rats and pectin may exhibit a lowering total lipid contents in serum and liver. Cellulose may slightly elevate serum and liver levels, or have no lowering effect.

• Applied Biological Chemistry
• /
• v.36 no.4
• /
• pp.277-283
• /
• 1993

In order to brew foxtail millet wine, a folk wine of Cheju, properties of raw materials, optimum brewing conditions were inveatigated. Carbohydrate and crude fat content of glutinuous foxtail millet are 71.27% and 3.47%, respectively. Since the ratio of water to steamed millet and ethanol concentration of wine showed negative correlation, less than 250% water had to added to steamed millet to maintain ethanol concentration in wine above 13%, Sugar consumption and ethanol production increased rapidly for the first 2 days, and main fermentation was done in 4 days. Ethanol concentrations were $13.0{\sim}13.4%$ when foxtail millet was used, and they were $14.0{\sim}14.3%$ for the mixture substrates of 90% millet and 10% rice or barley. Organic acids in millet wine were lactic acid, malic acid and succinic acid. The residual carbohydrates after fermentation were mainly xylose and oligosaccharides. A trace of methanol was detected in millet wine. The content of fusel oil was low, while the concnetration of organic acids was high. Optimum conditions for millet wine-making were as follows. Glutinuous foxtail millet with 10% rice as fermentation source need to be soaked in water and steamed for enough time. Water was added to steamed millet with the ratio of 2 : 1. The resulting mixture was stmnultaneously saccharified and fermented by Aspergillus orzae and Saccharomyces cerevisiae IAM 4274 at $20^{\circ}C$ for a week. Millet wine was prepared after filtering fermented broth while pressing for a week.

• Korean Journal of Plant Resources
• /
• v.20 no.2
• /
• pp.104-112
• /
• 2007

This study was carried out to investigate the effects of dietary tocotrienol extracted from the rice bran on hematological and histological changes of the mouse. The mice were divided into seven groups (basal diet, cholesterol diet, tocopherol diet, and 4 different tocotrienol diets), and bred for a month. Tocotrienol diet was shown to have decreasing effects of serum triacylglycerol and LDL concentrations, whereas serum HDL concentrations were increased by tocotrienol diet. But serum cholesterol concentration was not statistically significant among the diet groups. Tocotrienol diet was shown to have decreasing effects of serum AST activities (P=0.0548) and LDH activities (P=0.0016), which are the standard indicators for liver damages or myocardial infarction. And tocotrienol diet has reduced the fat bodies accumulated in liver and heart caused from administration of rice bran oil. Also, the effects were shown as concentration-dependent manners. In conclusion, dietary tocotrienol extracted from rice bran has evident effects to protect or reduce lipid accumulation from blood, hepatocytes and heart muscles. It is also suggested as a good fortifying nutrition for the health and medical care.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.2
• /
• pp.327-353
• /
• 1994

This study was performed to evaluate the effects of number and alignment of implant fixture and various bar designs on the retention of denture and the stress distribution. Six kinds of photoelastic mandibular models and nine kinds of overdenture specimens were designed. A unilateral vertical load was gradually applied on the right first molar to calculate the maximal dislodgement load of each specimen. A unilateral vertical load of 17 Kgf was applied on the right first molar and a vertical load of 10 Kgf was applied on the interincisal edge region. The stress pattern which developed in each photoelastic model was analyzed by the reflection polariscope. The results obtained were as follows: 1. The maximal dislodgement load reversely increased with the distance from the loading point to the implant fixture, while it linearly increased with that from the most posterior implant fixture to the mesial clip. The maximal dislodgement load also increased with the use of a cantilever bar. 2. Under the posterior vertical load, the stress to the supporting tissue of the denture base increased with the distance from the loading point to the implant future. The stress concentration on the apical area of the implant future reversely increased with the distance from the loading point to the implant future. 3. In the overdentures supported by two implant fixtures under the posterior vertical load. the specimen implanted on lateral incisor areas with a cantilever bar exhibited more favorable stress distribution than that without a cantilever bar. The specimen implanted on the canine areas without a cantilever bar, however, exhibited more favorable stress distribution. 4. In the overdentures supported by three implant fixtures. the specimen implanted ell the midline and canine areas exhibited more favorable stress distribution than that implanted oil the midline and the first premolar areas. 5. In the overdentures supported by four implant fixtures. the specimen implanted with two adjacent implant fixtures exhibited more favorable stress distribution than that implanted at equal distance under the posterior vertical load. 6. Under the anterior vertical load, the overdentures supported by three implant fixtures exhibited stress concentration on the supporting structure of the middle implant future. In overdentures supported by two or four implant futures, no significant difference was noted in stress distribution between the types of bars. These results indicate that the greater the number of implant fixtures, the better the stress distribution is. A favorable stress distribution may be obtained in the overdentures supported by two or three implant fixtures, if the location and the design of the bar are appropriate.