• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.131-136
• /
• 2008

The oil separation in an oil separator is one of the most important characteristics for proper compressor operation. In this study, a gravity type of oil separator is used. Oil separation characteristics has been investigated for $CO_2$/PAG mixture in the range of oil concentration 0 to 5 weight-percent and the mixture temperature range of $5^{\circ}C$ to $15^{\circ}C$ and $70^{\circ}C$ to $90^{\circ}C$. The results obtained indicate that the oil separation is increased with an increase in the oil concentration. It is also found that the oil separation in liquid state is increased with an increase in the mixture temperature while the oil separation in gas state is decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.160-164
• /
• 2000

This paper describes oil water separator using difference of electrical resistor. Oil is a non-conductive element and water is a relatively high conductive element. It is possible to detect water included in oil. Electric sensor is formed 8mm iron stick. Valve is operated With controller inputting signal of electric sensor. A experiment was done for necessary voltage in making program of controller. Oil water separator which was tested in field conditions was saved 7% of whole oil and was drained over 150% water than manual valve.

• Journal of computational fluids engineering
• /
• v.19 no.4
• /
• pp.8-13
• /
• 2014

A series of numerical simulation has been carried out to study performance of a cyclone type oil separator, which is designed for the compressor of a refrigeration system. Working fluid is R22, which is a typical refrigerant, and mineral oil droplet is supplied. Pitch of the helix is considered as design parameters to make a compact separator. Depending on the helix pitch, separation efficiency varies from 97.5 to 99%, while predicted pressure drop ranges from 5 to 6.5 kPa. Considering both of the pressure drop and separation efficiency, helix pitch of the separator has been designed as 50 mm.

• Journal of Power System Engineering
• /
• v.5 no.1
• /
• pp.64-72
• /
• 2001

According to the regulation of IMO, oil discharge from ships is allowed under 15ppm only and an oil filtering equipment is essential. However, for large ships using heavy fuel oil of over S.G 0.98 and viscosity 380cSt and system oil, it has been in difficulty to process with existing filtering type of oily water separator. A parallel plate type oily water separator which is one of gravity type separators can be used as an assistant equipment for the oil filtering system to meet the present IMO standard of 15 ppm, because it is an efficient method in dealing with a large amount of rich oil with high specific gravity. This work is focused on the fundamental investigation of the performance of the plate type oily water separator by visualization method and PIV(Particle Image Velocimetry) measurement to acquire multi-point velocity data simultaneously. The experimental results showed that the space of the plates acts a significant role in separating process and it was found that an important point to minimize a vortex flow is to flow a large amount of fluid in space of the plates in order to promote the efficiency of separation.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.803-812
• /
• 2023

The subsea separator of an offshore plant for offshore oil and gas development performs the process of separating oil and gas from crude oil produced in the subsea. The oil-gas subsea separator can be divided into a gravity type that separates fluids by gravity and an in-line type that separates fluids using centrifugal force of density. In the case of the deep sea, the development of a small in-line type separator is required due to manufacturing cost and safety problems caused by water pressure. Therefore, in this study, the gas-liquid phase separation efficiency of the subsea separator was identified through the study of the multiphase flow characteristics of the in-line type separator. For the optimal design of the in-line type separator, the shape of the internal swirl element(ISE) was selected first, and the separation efficiency results for each section of the in-line type separator were analyzed. This study was conducted in parallel with experiments and numerical analysis, and it is expected that the reliability and efficiency of the in-line type separator will be improved through the results.

• Journal of ILASS-Korea
• /
• v.25 no.4
• /
• pp.162-169
• /
• 2020

The worldwide focus on reducing the emissions, fuel and lubricant consumption in T-GDI engines is leading engineers to consider the crankcase ventilation and oil mist separation system as an important means of control. In today's passenger cars, the oil mist separation systems mainly use the inertia effect (e.g. labyrinth, cyclone etc.). Therefore, this study has investigated high efficiency cylinder head-integrated oil-mist separator by using a compact multi-impactor type oil mist separator system to ensure adequate oil mist separation performance. For this purpose, engine dynamometer testing with oil particle efficiency measurement equipment and 3D two-phase flow simulation have been performed for various engine operating conditions. Tests with an actual engine on a dynamometer showed oil aerosol particle size distributions varied depending on operating conditions. For instance, high rpm and load increases bot only blow-by gases but the amount of small size oil droplets. Submicron-sized particles (less than 0.5 ㎛) were also observed. It is also found that the impactor type separator is able to separate nearly no droplets of diameter lower than 3 ㎛. CFD results showed that the complex aerodynamics processes that lead to strong impingement and break-up can strip out large droplets and generate more small size droplets.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.4
• /
• pp.36-41
• /
• 2015

The cyclone separator is a simple device, which causes the centrifugal separation of materials such as droplets or particles in a fluid stream. The cyclone separator utilizes the energy obtained from fluid pressure and linear motion to create rotational fluid motion. This rotational motion leads the materials suspended in the fluid to separate from the fluid quickly due to the centrifugal force. The rotation is produced by the tangential or involuted introduction of fluid into the vessel. These materials may be droplets of fuel in blow-by gas through an engine. Droplets suspended in the feed liquid may separate according to size, shape, or density. And the change of part dimension in a cyclone separator can yield the its performance variation. The current study shows the influence of design parameters on the performance of a cyclone separator for blow-by gas.

• Journal of the Korean Society of Safety
• /
• v.12 no.2
• /
• pp.22-26
• /
• 1997

A small scale centrifugal oil separator consisted of two concentric tubes was fabricated for spilt oil recovery. With speed control of the inner tube, its performance of oil separation was investigated. Oil-water mixture is separated by forced vortex motion with the rotating inner tube. Velocity and pressure distributions in the tubes were calculated. Control of rotating speed, which is the most influencing parameter, showed an optimum value 946rpm corresponding to the acceleration of 20g at the inner tube surface. Separation performance was suddenly deteriorated at rotating speed higher than 1200rpm.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.4
• /
• pp.48-53
• /
• 2016

The centrifugal separator which uses gravity separation method for oil-water separation, rotating at high-speed, is one of the most commonly used device for controlling the amount of the oil in waste water collected in bilge. The IMO (International Maritime Organization) has set regulations, also known as MARPOL 73/78, for the prevention of marine pollution. In addition, DET NORSKE VERITAS (DNV) has set standards regarding the assignment of Environmental Class Notation, CLEAN or CLEAN DESIGN, of ships. One of the requirements for classification is that in addition to conforming to MARPOL 73/78, more stringent measures must be taken as well. One of these measures is to limit the oil concentration in bilge water to less than 5ppm. So in this study, an Oil-Water Separator (OWS) is used together with multiple separating plates as a filtration system to be used as an oil-water separation device. The OWS operates using centrifugal separation in which the mixture is separated by centrifugal forces. The main purpose of this paper is to present the OWS separation efficiency according to the rotation speed, mass-flow rate, the angle and the number of stacked layers of the laminated plate using Computational Fluid Dynamics (CFD). Improvements to the device will be investigated from these results.

• Journal of Animal Environmental Science
• /
• v.17 no.1
• /
• pp.33-38
• /
• 2011

Economic development involves increase in life expectancy as well as human health care. Consequently, demand for fish meal and fish oil is rapidly growing. In particular, Krill (Eupausia superba) oil product is in high demand due to its rich unsaturated-fatty acid, and thus stable supplies are necessary in the krill oil market. It is required for captured krills to be immediately frozen and stored during ship transport, since proteins of the krill are quickly denatured in natural temperature condition. However, the transportation cost has been sharply increased, which encourages researchers to involve in studies for development of efficient oil extraction process. In this study, a solid/liquid separation technique on boat for the krill oil was developed through triple separation tests using only a separator or using either brush or crusher prior to the separator. The separation tests revealed that the efficiency were 46.2, 60.2 and 60.4 % by the separator, combination with brush, and combination with crusher, respectively. In addition, it was found that byproduct, extracted cake, derived from the separation process could be used as a feed stuff. These results suggest that smashing using the brush or crusher prior to the separator is more efficient than using only the separator.