• Steel and Composite Structures
• /
• v.1 no.1
• /
• pp.131-144
• /
• 2001

Overpressurization can occur due to the ignition of flammable vapors existing inside aboveground oil storage tanks. Such accidents could happen more frequently than other types of accident. In the tank design, when the internal pressure increases, the sidewall-to-roof joint is expected to fail before failure occurs in the sidewall-to-bottom joint. This design concept is the socalled "frangible roof joint" introduced in API Standard 650. The major failure mode is bifurcation buckling in this case. This paper presents the bifurcation buckling pressures in both joints under internal pressure. Elastic and elastic-plastic axisymmetric shell finite element analysis was performed involving large deformation in the prebuckling state. Results show that API Standard 650 does not evaluate the frangible roof joint design conservatively in small diameter tanks.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.594-595
• /
• 2006

Porous bearings are lubricated the oil that is contained in porous metal. Then they are always used with no oil supply, because of that, widely used electric motors. But, if oil flow out less than the limit, troubles often happen. This report shows that attempt of estimating oil quantity in porous bearing by using calculation that based Reynols' equation and Darcy's law, aimed of developing long life bearing. And comparing with experimental and calculation result, we show possibility of estimating rest oil quantity in porous bearing at steadry state by calculation.

• Tribology and Lubricants
• /
• v.38 no.3
• /
• pp.109-114
• /
• 2022

This paper reports the development of an oil flushing system combined with a microbubble generator. Oil flushing plays a crucial role in regulating the lubricant's performance during the lubricant replacement process. Moreover, harmful contaminants, such as sludge, wear particles, and rust, from piping systems or lubrication system can be removed by oil flushing. Oil flushing aims to increase the system's efficiency using a dedicated flushing oil, increasing of the supply pressure and generating a vortex. In addition, it helps the mechanical system or equipment achieve peak performance and reduces the potential for premature failure. However, the contaminant-removal applications of existing oil flushing system are limited. In this research, we aim to improve the performance of oil flushing system by incorporating a microbubble generator, which uses the venture effect to generate microbubbles and mixes them with lubricant. The microbubbles in the blended lubricant remove contaminants from the lubrication system more effectively. Structural mechanics and fluid dynamics are analyzed through fluid-structure interaction (FSI) analysis, and the numerical analysis results are used for the designing the system. The magnitude of the maximum stress is investigated based on the pressure results obtained by the CFD analysis; through the CFD analysis, the mixing ratio of air (bubble) and lubricant is evaluated using the volume of fluid (VOF) model according to the working conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.9
• /
• pp.2909-2915
• /
• 1996

Precise and accurate pressure measurements are obtained using deadweight piston gauges. Pressure distribution and elastic distortion in the piston-cylinder unit are the leading factors in determination of effective area. The distortion depends upon the pressure distribution in the clearance between piston and cylinder and those are coupled each other. Considering the viscosity pressure relation of oil and governing flow equation in the clearance, a new numerical iterative algorithm is developed. The disagreement between the monotonous and sharp pressure profiles is an indication that the pressure profile will be different for each piston and cylinder unit due to material variances.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.329-334
• /
• 2003

Design of pre-compression region(trapping region) of the valve plate is an important element to minimize the pressure fluctuation in a cylinder and in discharge process, and pump noise. In this study, we tried to prove what the characteristics of the oil hydraulic pump would be according to the angle of the trapping region. Three kinds of asymmetrical valve plates were used. As a result, we found that by designing the trapping region, the slope of the pressure rise in the cylinder port from low-pressure suction region to high-pressure discharge region is relaxed and the pressure fluctuation width and the discharge pressure pulsation are reduced. Therefore, because the pump gets smooth pressure fluctuation and low fluid Impact, the pump noise is reduce.

• Korean Journal of Food Science and Technology
• /
• v.25 no.1
• /
• pp.28-32
• /
• 1993

In order to elucidate the temperature and pressure effect on the oil expression of perilla seed, recovery of expressed oil (REO) and volumetric strain of both roasted and unroasted perilla seeds were observed at different temperature, pressure and for different periods of press. In this experiment, moisture content of perilla seed was adjusted to 2.5% and temperature used were 30, 40, 50 and $60^{\circ}C$. Pressure applied were 10, 30, 50 and 70 MPa, and periods of press were 5, 7, 9 and 11 min. As temperature and pressure were increased or periods of press was lengthened, REO and volumetric strain of pressed cake were increased. Maximum REO of unroasted perilla seeds were found to be 85.59% and those of roasted perilla seeds be 85.30%, at 70 MPa, $60^{\circ}C$, and for 11 min. Viscosity of expressed oil were exponentially dependent on temperature and REO were increased as viscosity was decreased. From statistical analysis between effects of expression factors and REO and volumetric strain of pressed cake, importance of their effects was decreased in the order of pressure, temperature, $temperature{\times}pressure$ and periods of press. The multiple regression equation between REO(Y) and temperature (T), pressure (P), and periods of press (D) were as follows; $Y=7.95+36.85P+1.12T^2-0.55TP-5.08P^2\;r^2=0.97$ for unroasted perilla seed (p<0.01), $Y=4.50T+39.23P+0.83T^2-1.71P-5.07P^2\;r^2=0.99$ for roasted perilla seed (p<0.01).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.2
• /
• pp.516-521
• /
• 2012

Computational simulation has been conducted to analyze the oil separation performance of gasoline engine oil separators. Two models are compared to select a proper oil separator for the engine. To analyze oil separation characteristics, d50 and separation efficiency have been calculated for each separator. As a result, model A shows excellent d50 and separation efficiency, and model B shows good pressure-drop characteristics. Model B is recommended for the general gasoline engine with low crank-case pressure and low oil consumption. Model A is recommended for the engine with high crank-case pressure and high oil consumption, especially equipped with special exhaust gas treatment system, that is critical to the oil contamination.

• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.23-30
• /
• 2017

The electric controlled marine diesel engine has fuel pump generating the high pressurized fuel for fuel injection to combustion chamber via a common rail. Fuel pump consists of a cam-roller system. Journal bearing installed between a roller and a cam-roller pin is subjected to fluctuating heavy and instant loads by cam lift. First, Kinematic analysis is carried out to predict bearing loads during one cycle acting on the journal bearing. Second, flexible multi-body dynamic analysis and transient elasto-hydrodynamic(EHD) lubrication analysis for journal bearing considering elastic deformation of cam-roller pin, roller and bearing are conducted using AVL EXCITE/PU software to predict lubrication performance. The clearance ratio and journal groove shape providing lubrication oil are important parameter in bearing design having good performance and can be changed easier than other design parameters such as diameter, width, oil supply pressure and bearing material grade. Generally, journal bearing performance is represented by the minimum oil film thickness(MOFT) and peak oil film pressure(POFP). As well as the traditional design parameters(MOFT, POFP), in this study, temperature rise of lubrication oil is also evaluated through the side leakage flow of supplied oil. By the evaluating MOFT, POFP and temperature rise, the optimum bearing clearance ratio is decided.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1116-1122
• /
• 2009

As a result of this study, we reached the following conclusions. With appropriate setting of oil pressure and flow rate, it operated same rotation speed with existing cooler by electrical transmission. In initial operation, a temperature of a cold storage is lower rapidly. As an internal temperature of a cold storage is lower, a decreasing rate of temperature is lower. As a result of comparing the both type, the cooler of oil pressure type showed the following results. The decreasing rate of temperature was more faster and shorter operating time was more shorter than existing cooler of electric type. The actual case of a cold storage, the cooler of oil pressure type can prevent quality deterioration and decrease power consumption. As an internal temperature of a cold storage is lower, power consumption increased rapidly, the oil pressure type showed lower power consumption. COP of two of these types decreased continuously as the internal temperature of a cold storage being reach setting temperature, and that of oil pressure type showed higher amount about 25%. As a setting temperature is lower, the number of refrigerator's operating times are less and operating time is longer, so power consumption is increased in the maintenance of a cold storage's internal temperature, power consumption of hydraulic type showed lower amount about 21~25% in two of these types.

• Korean Chemical Engineering Research
• /
• v.54 no.5
• /
• pp.606-611
• /
• 2016

Carbon dioxide injection is a widely known method of enhanced oil recovery (EOR). It is critical for the $CO_2$ EOR that the injected $CO_2$ to reach a condition fully miscible with oil. To reach the miscible point, a certain level of pressure is required, which is known as minimum miscibility pressure (MMP). In this study, a MMP prediction method using a process simulator is proposed. To validate the results of the simulation, those are compared to a slim tube experiment and several empirical correlations of previous literatures. Aspen HYSYS is utilized as the process simulator to create a model of $CO_2$/crude oil encounter. The results of the study show that the process simulator model is capable of predicting MMP and comparable to other published methods.