• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.103-108
• /
• 2003

The effect of equivalence ratio and fuel/air mixing quality on the phase-resolved gas temperatures at different phases of the oscillating pressure cycle was experimentally investigated. An atmospheric pressure, optically accessible and laboratory-scale dump combustor operating on methane with heat release rate of 1.59kW was used. Temperature measurements were made using coherent anti-Stokes Raman spectroscopy (CARS) at several spatial locations for typical unstable combustion conditions. Analysis was conducted using parameters such as phase-resolved averaged temperature, normalized standard deviation and temperature probability distribution functions (PDFs). Also the probability on the occurrence of high temperature (over 1900K) was investigated to get the information on the perturbation of equivalence ratio and NOx emission characteristics. It was shown that most of temperature histograms exhibit Gaussian profile which has short breadth of temperature fluctuation at equivalence ratio of 0.6, while beta profile was predominant for the cases of other equivalence ratios (${\Phi}$=0.55, 0.50). The characteristics on the occurrence of high temperature also displayed periodic wave form which is very similar to the pressure signal. And the amplitude of this profile goes larger as the fuel/air mixing quality become poorer. These also provided additional information on the perturbation of equivalence ratio at flame as well as NOx emission characteristics.

• 한국방재학회 논문집
• /
• 제8권2호
• /
• pp.129-138
• /
• 2008

차수성이 요구되는 제체나 댐체에 대하여 안정성을 판단하고자 할 경우 파이핑 현상발생 여부를 검토한다. 제체나 댐체는 층 다짐을 수행하면서 축조되므로 투수성은 수평방향 투수계수($k_x$)와 연직방향 투수계수($k_y$)가 서로 다른 이방성이 될 수 있다. 본 연구에서는 여러 가지 투수계수 비(k-ratio=$k_y/k_x$k)에 따른 침투해석을 수행하여 유출동수경사와 침투유속을 파악하고, 이론식에 의한 한계동수경사와 경험식에 의한 한계유속과 각각 비교.검토하여 파이핑에 미치는 영향을 검토하였다. 연구결과 투수계수 비는 한계동수경사 개념으로 파이핑 현상발생에 대한 안정성을 검토할 경우 매우 중요한 요소로 작용하나, 한계유속 개념에 대해서는 상대적으로 중요도가 매우 낮은 것으로 확인되었다.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.27-33
• /
• 2001

In this study, it is observed that the distribution of combustion chamber volume affects the volumetric efficiency. The distribution ratio was adjusted by controlling combustion chamber volume of head and piston bowl one. Four cases were investigated, which are the combination of different distribution ratios and different compression ratios (9.8-10.0). A commercial SOHC 3-valve engine was modified by cutting the bottom face of the head and/or replacing the piston by the one that has different volume. The result shows that the less the head side volume, the more volumetric efficiency is achieved under the same compression ratio. It is also observed that increasing volumetric efficiency results in early knock occurrence due to increased "real" compression ratio. To consider reliability in estimating the volumetric efficiency, we examined the sensitivity of the AFR equation to possible errors in emission measurements. It is shown that the volumetric efficiency, which is calculated by measuring AFR and fuel consumption, can be controlled in 1% error. 1% error.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2006년도 춘계학술논문 발표대회 제6권1호
• /
• pp.57-61
• /
• 2006

Waste foundry sand of industrial waste which is happening by vast quantity according to fast development of industry has much the occurrence amount and processing method is depended on reclamation, and is using by fine aggregate for construction by recycling method among others. In this research Waste foundry sand powder into cement replace fare use possibility availability judge wish to Slump and air content decreased the replacement ratio increases by concrete special quality that do not harden according to experiment result, and unit capacity mass and bleeding increased the replacement ratio increases. Hardening concrete intensity special quality displayed strength improvement to replacement ratio 20%, and tendency that watertightness increases most in replacement ratio loft in watertight property appear. Considering the strength and watertight properties, the adequate usage of waste foundry sand powder is the 10% of replacement ratio.

• 한국광물학회지
• /
• 제7권1호
• /
• pp.1-13
• /
• 1994

국내 산업에 활용되는 광물은 약 50종으로서 이 중에서 산업소재광물 (비금속광물)은 27종에 이른다. 산업소재광물이 차지하는 생산금액은 모든 광물자원 (석탄 제외)이 차지하는 금액의 70 %를 상회한다. 1983년부터 1992년까지 광업 및 제조분야의 성장률은 연평균 11.5 % 그리고 GNP는 14.8 %의 성장률을 보인 반면 광물자원의 수요는 2.7배로서 이중 석회석은 생산과 수요에 있어 선두를 차지하며 납석은 수출면에서 수위를 점하고 있다. 생산에 대한 수출비율은 1983년도에 12.2 %에서 1992년도에는 4.2 %로 그리고 수입비율은 84 %에서 38.2 %로 하향되었다. 국내 산업소재 광물자원으로서 중요 역할을 담당하는 것으로 석회석, 납석 그리고 고령토를 들 수 있는 바, 석회석은 캠브리아기의 풍촌석회암층에 고품위가 부존되어 있으며, 납석은 경상 및 전라지역에 발달된 백악기 유천그룹의 화산암 내에, 그리고 고령토는 경상남북도 지역에 분포된 회장암 풍화대에서 발달 양상을 잘 확인할 수 있다.

• 한국통신학회논문지
• /
• 제35권12A호
• /
• pp.1097-1104
• /
• 2010

본 논문에서는 IEEE 802.16m IMT-Advanced WiMax 단말에서 SNR(Signal to Noise Ratio)과 SINR(Signal to Interference Plus Noise Ratio)을 측정하는 블록의 설계에 대해 기술하였다. IMT-Advanced 시스템을 위한 IEEE 802.16m 규격에서는 하향링크로 PA-Preamble과 SA-Preamble의 두 가지 A-Preamble (Advanced Preamble) OFDM 심볼을 전송하는데, 이를 이용하면 SNR과 SINR을 정확히 측정할 수 있으며, Doppler등에 의해 ICI(Inter-Carrier-Interference)가 발생했는지의 여부도 알 수 있다. 본 논문에서는 IEEE 802.16m 시스템의 단말에서 PA-Preamble의 SA-Preamble을 이용하여 SINR을 측정하고 ICI가 발생했는지 여부도 판정하는 SNR/SINR 측정 방법과 시뮬레이션 결과를 제시하였다. ICI의 발생여부를 정확히 인지할 수 있으면, 단말은 평소에는 l-Tap 등화기만 사용하다가 ICI가 있을 때에만 복잡한 ICI 완화를 수행하면 되므로 성능 향상 뿐 아니라 저전력 특성까지 향상시킬 수 있다.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.25-34
• /
• 2010

Fretting damage reduces fatigue life of the material due to low amplitude cyclic sliding and changes in the contact surfaces of strongly connected machine and structures such as bolt, key, fixed rivet and connected shaft, which have relative slip of repeatedly very low frequency amplitude. In this study, the fretting fatigue behavior of 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were evaluated. The plain fatigue test and fretting fatigue test under cyclic bending load carried out commercial bending fatigue tester and specially devised equipments to cause fretting damage. From these experimental work, the following results obtained: (1) The plain fatigue limit for stress ratio R=-l was about 151MPa. (2) In case of fretting fatigue, fatigue limit for stress ratio R=-l about 72MPa, the fatigue limit for R=0 about 81MPa, and the fatigue limit for R=0.3 about 93MPa. (3) The fatigue limit reduction rates by the fretting damage were about 52%(R=-1), 46%(R=0) and 38%(R=0.3) respectively. (4) The fatigue limit reduction rate decreased with stress ratio increase. In fretting bending test, as stress ratio increased, occurrence of initial oblique crack by fretting decreased or phased out, so that fracture surfaces were formed by plain fatigue crack occurrence, and such tendency was notable as stress amplitude increased. (5) Tire tracks and rubbed scars were observed in the fracture surface and contacted surface.

• Ocean and Polar Research
• /
• 제44권3호
• /
• pp.191-207
• /
• 2022

Using the results of CTD casts made in Spring from 2017 to 2021, in this study we investigated the water mass distribution and occurrence of temperature inversion in the western seas of Jeju Island in spring. The distribution of water masses was characterized by cold and fresh water in the northwest and warm and saline water in the southeast, forming a strong thermohaline front running in the southwest-to-northeast direction. Strong temperature inversion mainly occurred in the frontal boundary when the cold water intrudes beneath the warm water at depths of 30-50 m. Analysis of the mixing ratio demonstrated that Jeju Warm Water is dominantly distributed in the western seas of Jeju Island, but its ratio can be modified depending on the southward extension of Yellow Sea Cold Water (YSCW). Results of in situ measurement showed that in 2020, the YSCW largely expanded to the western seas of Jeju Island, occupying approximately 40 % of the mixing ratio. Due to the expansion of YSCW, a strong thermohaline front was formed in the study area, thereby causing thick and strong temperature inversion. On the other hand, in 2018 the mixing ratio of YSCW was minimum (~18%) during the study period of 2017-2021, and thus a relatively weak frontal boundary was formed, without the occurrence of temperature inversion. The observational results also suggest that the interannual changes of water mass distribution and the associated temperature inversion in the western seas of Jeju Island are closely related with wind-driven Yellow Sea circulation in spring, which is the summer monsoon transition period.

• 환경위생공학
• /
• 제14권4호
• /
• pp.50-68
• /
• 1999

The present study was performed to examine on the fauna and standing crops of benthic macroinvertebrates in Pongwha and Youngwol region of upper parts of south han river and Naktons river. The Actual site suvry was caried out on the two times during the April·June to October·November, 1988. Main five areas are Mt. Awrawe(1,067m), Mt. Sontal (1,236m), Mt. Munsu(1,206m), Peak Okyopong(357m) and Mt. Pungnak(760m) area. Total taxa of benthic macroinvertebrates of the study area were 118 species, 45families12 orders, 5 classes in 4 phyla. Occurrence species according to the major taxa of aquatic insects were 35 species (29.66%) in ephemeroptera, 25 species(21.19%) in trichoptera, 25 species(21.19%) hemiptera, 1 species(0.85%) in megaloptera. Non-aqautic insect were 5 species in mollusca, 3 ratio was 8.5 percent. Occurrence species(plecoptera) at clean waters were appeared 12 species at Mt. Awrawe and Sontal area. Occurrence species at each survey area was 67 species at Mt. Awrawe area, 60 species at Mt. Sontal area, 43 species at Mt. Munsu area, 37 species at Mt. P'ungnak area and 34 species at Peak Okyo area, respectively. Species diversity indices were 2.96~3.80 at Mt. Awrawe area, 2.79~3.62 at Mt. sontal area, but 2.64~3.12, 1.59~2.46 and 1.98~2.59 at, Mt. Munsu, P'ungnak and Peak Okyo area, respectively. In this region, occurrence species and individual density were smaller than that of Dong river with good habitat, but those were more abundant than that of Poseong river with similar environment conditions. Therefore, occurrence species and individual density of the present survey region were appeared as somewhat abundant.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 추계학술대회
• /
• pp.764-765
• /
• 2010

인체의 진단에 사용되는 의료용 X선 기기는 비 침습적인 방법으로 인체 내부의 진단이 가능하여 의료기관에서 진단에 매우 큰 비중을 차지하고 있다. X선의 발생에 가장 중요한 고전압 발생장치는 기존 변압기 식이 주로 사용되었으나 크고 무거우며 직류 고전압의 리플이 커서 발생효율이 낮다. 이러한 단점을 보완하기 위해 인버터를 사용하여 입력전원의 주파수를 고주파하는 인버터 방식의 고전압 발생장치가 주로 사용되고 있다. 본 연구에서는 펄스폭 변조 방식을 적용하여 관전압과 관전류의 동작을 제어 하였으며, 오실로 스코프를 이용하여 동작 결과를 확인하였다.