• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.1
• /
• pp.73-79
• /
• 2009

Hazardous materials (HazMats) are substances that are flammable, explosive, toxic, or harmful, if released into the environment. Since the transportation of HazMats increases in many developed countries, HazMat transportation has the key function in the process of HazMat usage to trace information of production, storage, shipment, usage, and waste disposal. The Korean Ministry of Environment (KMOE) and the National Emergency Management Agency (NEMA) have developed many laws, regulations, and standards for hazardous materials. However, the Korean HazMat laws, regulations, and standards do not guarantee accurate information of HazMat origin-destination (O-D) shipments, though the HazMat O-D movement is the critical information in safety and security of HazMat transportation. The objectives of this research are: (1) to investigate emerging and recurrent issues in Korean HazMat transportation, and (2) to develop the estimation method of O-D matrices for hazardous materials under limited data sets. The sodium hydroxide waste shipment among forty candidate HazMats is selected as the sample research case. The growth-factor method is applied to estimate the 2005 O-D matrix of sodium-hydroxide waste shipment. The column-and-row factoring process is used to calibrate the estimated sodium-hydroxide O-D matrix. The result shows the applicability of the O-D estimation process for hazardous materials. The Sodium Hydroxide Waste Origin-Destination Matrix is obtained to trace routes and paths of the Sodium Hydroxide transportation.

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.22-22
• /
• 1991

광의 병렬처리 능력을 잘 활용한 1$\times$4 매트릭스 스위치의 구조와 전극구조를 설계하고 스위치 특성을 조사하기 위하여 beam propagation method(BPM)를 이용하여 수치계산을 하였다. 기존의 매트릭스 스위치는 대부분의 경우 방향성 결합기를 스위치 element로 이용하여 왔으나 이 결합기는 소자의 길이가 길기 때문에 단일 LinBO3 웨이퍼상에 집적할 수 있는 매트릭스 스위치의 크기가 제한되는 단점이 있다. 본 연구에서는 두 도파로 사이에 세 번째 도파로를 삽입하여 두 도파로를 결합시키는 세 도파로 결합기를 스위치 element로 사용하여 세 개의 스위치 element를 LiNbO3기판위에 직렬로 집적시킨 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치의 특성을 BPM을 사용하여 수치계산할 때 단일 모드 도파로의 유효 굴절을 분포는 n(X) = nm + $\Delta$ncosh-2(2x/w)의 형태로 가정했으며, 사용된 파라미터의 값은 각각 nm=2.1455, $\Delta$n=0.003, W=5$mu extrm{m}$, d=5$\mu\textrm{m}$, λ=1.3$\mu\textrm{m}$ 이고 S-파라메터의 값은 0.95927이므로 단일 모드 도파로가 된다. 계산결과 스위치 element의 결합길이는 3810$\mu\textrm{m}$이며 도파로의 길이가 결합길이와 같을 때 전극에 인가된 전압에 의한 도파로의 굴절을 섭등의 함수로 출력광의 세기를 계산한 결과 스위칭 전압은 14.85volt이고 crosstalk는 -18.9dB였다. 이 스위치 element로 구성된 1$\times$4 매트릭스 스위치는 스위칭 전압을 세 개의 전극에 적절한 조합으로 인가함으로써 한 입력 도파로에 결합된 광이 내개의 출력 도파로중 한 도파로에 스위칭 된다. 한편 수치계산의 결과를 실험적으로 확인하기 위해 스위치 element와 1$\times$4 매트릭스 스위치를 z-cut의 LinbO3 결정에 Ti을 열확산시켜 제작한 소자의 스위칭 특성을 발표할 예정이다.

• Applied Chemistry for Engineering
• /
• v.26 no.4
• /
• pp.406-412
• /
• 2015

Unidirectional carbon/carbon (C/C) composites were manufactured using phenolic resins as a precursor of the carbonized matrix throughout a one-step manufacturing process. Also, molybdenum oxide ($MoO_3$) and binder pitches were impregnated with phenolic resins to improve the bulk density and mechanical property of the C/C composites. In this study, the influence of $MoO_3$ and binder pitches on mechanical properties of the C/C composites were investigated by measuring flexural strength (${\sigma}_f$) and interlaminar shear strength (ILSS). The results show that the enhancement of interfacial adhesions between the fibers and matrix resins of the C/C composites with $MoO_3$ and binder pitches which led to the improvement of mechanical properties of the C/C composites. This indicates that the presence of $MoO_3$ and binder pitches in C/C composites can develop the graphite structure and increase the bulk density.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.5
• /
• pp.598-606
• /
• 2022

With the advancement of industry, the use of various sustainable energy sources and solutions to problems affecting the environment are being actively requested. From this point of view, it is intended to directly burn unused biogas to use it as energy and to solve environmental problems such as greenhouse gases. In this study, a new type of cavity matrix combustor capable of low-emission complete combustion without complex facilities such as separation or purification of biogas produced in small and medium-sized facilities was proposed, and CFD numerical calculation was performed to understand the performance characteristics of this combustor. The cavity matrix combustor consists of a burner with a rectangular porous microwave receptor at the center inside a 3D cavity that maintains a rectangular parallelepiped shape composed of a porous plate that can store heat in the combustor chamber. As a result of numerical calculation, the biogas supplied to the inlet of the combustor is converted to CO and H₂, which are intermediate products, on the surface of the 3D matrix porous burner. And then the optimal combustion process was achieved through complete combustion into CO₂ and H₂O due to increased combustibility by receiving heat energy from the microwave heating receptor.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.439-452
• /
• 1994

A method to optimize the cost of R/C frames and an algorithm of the optimal limit state design for R/C frames subjected to dynamic loads are presented. The modal superposition method was used to find the dynamic responses of the frames. Each member of R/C frame is made up of more than two elements and the stiffness matrix and consistent mass matrix of three d.o.f in the node of each element was used to include axial, shear and flexural effects. The objective function to be minimized formulated the cost of materials, steel and concrete, and optimised to satisfy the behaviors of R/C frame and each constraint imposed by the limit state requirements. Both objective function and each constraint are derived in terms of design variables which include the effective depth, beam width, compression and tension steel area, and column shear steel area. A few applications are presented which demonstrate the feasibility, the validity and efficiency of the algorithm for automated optimum design of R/C frames where dynamic behavior is to be considered.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.11
• /
• pp.2512-2520
• /
• 1997

The classes of Reverse Jacket matrix [RJ]$_{N}$ and the corresponding Restclass Reverse Jacket matrix ([RRJ]$_{N}$) are defined;the main property of [RJ]$_{N}$ is that the inverse matrices of them can be obtained very easily and have a special structure. [RJ]$_{N}$ is derived from the weighted hadamard Transform corresponding to hadamard matrix [H]$_{N}$ and a basic symmertric matrix D. the classes of [RJ]$_{2}$ can be used as a generalize Quincunx subsampling matrix and serveral polygonal subsampling matrices. In this paper, we will present in particular the systematical block-wise extending-method for {RJ]$_{N}$. We have deduced a new orthorgonal matrix $M_{1}$.mem.[RRJ]$_{N}$ from a nonorthogonal matrix $M_{O}$.mem.[RJ]$_{N}$. These matrices can be used to develop efficient algorithms in IMT2000 signal processing, multidimensional subsampling, spectrum analyzers, and signal screamblers, as well as in speech and image signal processing.gnal processing.g.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.25-32
• /
• 1988

A formulation of an isoparametric quadrilateral higher-order plate bending finite element is presented. The 8-noded 28-d.o.f. plate element has been degenerated from the three-dimensional continuum by introducing the plate assumptions and considering higher-order in-plane displacement profile. The element characteristics have been derived by the Galerkin's weighted residual method and computed by using the selective reduced integration technique to avoid shear-locking phenomenon. Several numerical examples are given to demonstrate the accuracy and versatility of the proposed quadrilateral higher-order plate bending element over the other existing plate finite elements in both static and dynamic analyses.

• Applied Chemistry for Engineering
• /
• v.24 no.4
• /
• pp.363-369
• /
• 2013

In this work, the effects of ozone treatments on mechanical interfacial properties of carbon fibers-reinforced nylon-6 matrix composites were investigated. The surface properties of ozone treated carbon fibers were studied by Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). Mechanical interfacial properties of the composites were investigated using critical stress intensity factor ($K_{IC}$). The cross-section morphologies of ozone-treated carbon fiber/nylon-6 composites were observed by scanning electron microscope (SEM). As a result, $K_{IC}$ of the ozone-treated carbon fibers-reinforced composites showed higher values than those of as-received carbon fibers-reinforced composites due the enhanced $O_{1s}/C_{1s}$ ratio of the carbon fiber by the ozone treatments. This result concludes that the mechanical interfacial properties of nylon-6 matrix composites can be controlled by suitable ozone treatments on the carbon fibers.

• Korean Journal of Food Science and Technology
• /
• v.37 no.4
• /
• pp.513-518
• /
• 2005

Capillary electrophoresis (CE) method was developed to determine (+)-catechin and (-)-epicatechin contents in grape seed ethanol extract. CE separation was achieved using 100 mM phosphate and borate buffer at pH 6.0 as background electrolyte and fused silica capillary with 50 microns x 375 microns O.D. (effective length 20.0cm) maintained at $25^{\circ}C$. The applied voltage was 10kV, and detection was performed by DAD at 210 nm, Two catechins were well separated within 6 min with repeatability of <0.8% RSD for migration time and <2.0% RSD for peak area, and correlation coefficients higher than 0.994 were obtained from 58.0 to 174.0 mg/L with detection limit of 0.035 mg/L. Separated compounds were successfully determined. CE method was easy to handle and showed good reproducibility. CE method was compared with conventional coloring and HPLC methods, and main advantages of CE method were low amount of sample required, simple pre-sample treatment, good recovery rate, and short analysis time.