• Journal of the Korean Applied Science and Technology
• /
• v.28 no.4
• /
• pp.402-409
• /
• 2011

Compatibility and properties of PP/N66 blends with or without PP-g-MAH as a compatibilizer were investigated by DSC, SEM and universal testing machine. Morphological studies revealed that PP and N66 were incompatible and addition of PP-g-MAH was very effective to enhance the compatibility between PP and N66. The compatibilization effect between N66 and PP-g-MAH was based on the reaction between the amine end group of N66 and anhydride group in PP-g-MAH. The crystallization and melting behavior of PP/N66 blends were investigated and the results of analyses for enthalpy changed were discussed. The Izod impact strength could be improved by optimizing the compatibilizer concentration. Tensile strength, elongation at break, notched Izod impact strength were increased with using compatibilizer, however, both the compatibilized and the noncompatibilizer blends did not show any big difference in the flexural modulus.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2354-2358
• /
• 2007

MALDI-TOF-MS technique was applied to obtain structural and compositional information of synthetic polyamides, Nylon6 and Nylon66. Mass spectra of both the original and the hydrolyzed polyamide samples were analyzed using the self calibration method as well as the internal calibration method with the standard materials of known masses. The MALDI-TOF mass spectra of Nylon6 samples showed the presence of protonated, sodiated, and potassiated ions that were assigned to cyclic and NH2/COOH terminated linear oligomers. From the MALDI-TOF mass spectra of Nylon66 samples, the potassiated linear oligomers with three different end groups are identified as well as the cyclic oligomers, i.e., NH2/COOH terminated oligomers, NH2/NH2 terminated oligomers, and COOH/COOH terminated oligomers. Full characterization of the molecular species and end groups present in the polyamide samples has been achieved, and also the changes in mass spectral patterns after the hydrolysis of the samples are presented.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2359-2362
• /
• 2007

MALDI-TOF-MS technique was applied to obtain structural and compositional information of synthetic polyamides, Nylon6 and Nylon66. Mass spectra of both the original and the hydrolyzed polyamide samples were analyzed using the self calibration method as well as the internal calibration method with the standard materials of known masses. The MALDI-TOF mass spectra of Nylon6 samples showed the presence of protonated, sodiated, and potassiated ions that were assigned to cyclic and NH2/COOH terminated linear oligomers. From the MALDI-TOF mass spectra of Nylon66 samples, the potassiated linear oligomers with three different end groups are identified as well as the cyclic oligomers, i.e., NH2/COOH terminated oligomers, NH2/NH2 terminated oligomers, and COOH/COOH terminated oligomers. Full characterization of the molecular species and end groups present in the polyamide samples has been achieved, and also the changes in mass spectral patterns after the hydrolysis of the samples are presented.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.6
• /
• pp.3990-3996
• /
• 2014

Because the physical properties can be decreased when a Nylon 66/glass fiber composite is injected into a mold over $300^{\circ}C$, a systematic study of the thermal history in the case of re-use is needed. Nylon 66/glass fiber extrudates as a function of the extrusion number were prepared using a twin screw extruder at 305/290/273/268/265/$260^{\circ}C$. The chemical structure, thermal properties, melt index, crystal structure, Izod impact strength, and rheological properties were measured by Fourier transform infra-red (FT-IR), melt indexer, DSC, TGA, XRD, Izod impact tester, and dynamic rheometer. The FT-IR spectra indicated that the number of extrusions did not affect the chemical structure. The decrease in molecular weight with increasing extrusion number was confirmed by the melt index and the complex viscosity of extrudates. Based on the DSC and TGA results, the thermal history had no effect on the melting temperature, regardless of the number of extrusions, but the degradation temperature decreased up to $20^{\circ}C$ with increasing extrusion number. The Izod impact strengths of the extrudates were found to decrease with increasing extrusion number. No structural change after extrusion was also confirmed because there was no change in the slope and shape of the G'-G" plot.

• Proceedings of the Korean Fiber Society Conference
• /
• 1997.04a
• /
• pp.235-239
• /
• 1997

• Journal of the Korean Institute of Gas
• /
• v.11 no.1 s.34
• /
• pp.34-39
• /
• 2007

In this paper, the FEM result has been presented for a sealing safety between a valve packing and a valve seat during a open and close operation in a LPG cylinder. The sealing operation of a LPG valve is completed when the valve packing in which is made by a nylon-66 polymer is to stop a LP gas flow, which flows out from the outlet of a brass pipe in a LPG cylinder. The contact sealing mechanism of the valve may be classified by a flat contact of an unused valve packing and a circular groove contact of an used valve packing in a current LPG valve. Based on the FEM and experimental investigations the sealing force, 4.9 MPa for a flat contact mode of the unused valve packing is a little high compared to that of the used valve packing, which shows a circular groove contact geometry against a valve seat. But these sealing pressures for two contact modes are very low compared to the ultimate strenath 83 MPa of the nylon-66 and this may be designed with a excess strength of the valve.

• Fashion & Textile Research Journal
• /
• v.5 no.3
• /
• pp.267-272
• /
• 2003

Tactel(Nylon66) union fabrics were woven with the specification of 70d/34f nylon as warp for sport wear jacket. Weft yarn has three types; 100% cotton yarn, nylon core-spun yarn and nylon-polyurethane covering yarn as weft. Fabric structers were plain, twill and satin weave structure with the air jet loom. The mechanical properties of 8 fabrics were measured with KES-F and primary Hand Values and Total Hand Values were calculated. The results of the study were as follows: 1) There was little difference among LTs of N/CM fabric groups. RT of the fabrics with CM100's was bigger than that of fabrics with CM80's, resulting that the fabrics with CM100's have better formability. In terms of weaving structure, twill fabrics have shape deformation. 2) In comparison of RTs with weft yarn type, RT of N-PU covering yarn was the highest, followed by Nylon core-spun yarn and cotton yarn. Thus, the fabric with N-PU covering yarn has better stability of shape deformation. 3) Stretch yarn could express an excellent silhouette formation and twill and satin structures were better structure to make curvature on human form. 4) 2HG/G value of nylon core-spun fabrics was larger than that of N/C fabrics, but the silhouette formation of N/C fabrics was excellent. 5) The RC of N/PU was the highest, followed by N/P, and N/CM. 6) Koski of N/PU fabrics was the highest, Numeri of N/PU and N/Co-I were relatively higher than the others. THVs of N/CM-IV and N/CO-II were lower than the others, resulting that, twill structure was better than plain structure for a sport wear uses.

• Membrane and Water Treatment
• /
• v.10 no.6
• /
• pp.441-449
• /
• 2019

In this study, cellulose acetate (CA) / nylon66 (NYL66) (95/5) blend membranes with different thicknesses were prepared by a solvent evaporation method. The effects of membrane thickness (almost $7-25{\mu}m$), feed concentration (70-95 wt.% isopropanol), and feed temperature ($30-60^{\circ}C$) were investigated on the performance of membrane in the separation of isopropanol-water mixtures. With regard to the results of sorption experiments, it was found that the increase of feed temperature enhanced the overall sorption while by increasing feed concentration, the overall sorption passed through a maximum value at 70 wt. % isopropanol (IPA). The best separation factor 3080.51 was gained at high isopropanol concentration 95 wt.%, low feed temperature $30^{\circ}C$, and high membrane thickness $24.62{\mu}m$. Regarding the pervaporation separation index, the obtained results showed that proper values for the thickness of membrane, feed temperature, and isopropanol concentration in feed were $24.62{\mu}m$, $40^{\circ}C$, and 70 wt.%, respectively.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2008.04a
• /
• pp.159-161
• /
• 2008

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2005.11a
• /
• pp.147-148
• /
• 2005