• 한국해양공학회지
• /
• 제6권2호
• /
• pp.143-150
• /
• 1992

Numerical simulation is made of a stably stratified salt-water solution due to lateral heating in an equilateral trapezoidal enclosure using boundary-fitted coordinate in grid generation. Results show four types of the global fluid pattern depending on the buoyancy ratio in the enclosure, i.e., unicell flow pattern for the low buoyancy ratio, layered flow pattern for the increasing buoyancy ratio, layered flow pattern with stagnant zone for the relatively high buoyancy ratio and stagnant flow pattern for the much higher buoyancy ratio.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1275-1282
• /
• 2005

This paper deals with the numerical study for excavation crossing the fault zone and the change of support pattern in field. The numerical analyses by FLAC program were performed to evaluate the suitable support pattern influenced by the width of Fault Zone, considering rock mass condition(RMR classification). Based on the results, it is found that partial reinforcement or degrading support pattern is suitable, when the width of Fault is under 3m. But when the width of Fault is more than 6m(0.5D), extra support pattern for fault zone is acceptable. At field, this result is generally used as a guide in the construction of roadway tunnel, but it is also possible to vary this assessment along the condition of fault.

• 한국생산제조학회지
• /
• 제23권3호
• /
• pp.291-298
• /
• 2014

This study uses two numerical approaches to analyze the filling behavior of micro patterns on micro-injection molding for V-grooves pattern which cannot be simulated with conventional CAE packages. The parametric studies have been performed to examine the fidelity of micro patterns with respect to temperature, pressure, inlet velocity and pattern location on the mold according to the boundary condition from the macro pressure and velocity data which can be obtained by conventional CAE packages. Through these numerical approaches, the filling behavior of polymer melt in micro patterns can be understood, the quality of replication can be predicted, and the V-groove pattern can be shaped uniformly during the process of injection molding.

• 한국공간구조학회논문집
• /
• 제1권1호
• /
• pp.157-166
• /
• 2001

In general, the cutting pattern of the membrane structures is determined by dividing the complicated curved 3-D surface into several 2-D plane strip by using flattening technique. In this procedure, however, some discrepancies ore occurred between actual stresses of equilibrated state and designed uniform stresses because the material properties are not considered. These deviations can cause the critical structural problems, wrinkling or overstress, and thus a optimization process should be considered. In this paper, a new analytical method for determining an optimum cutting pattern considering material properties is presented. Here, iterative procedure is introduced to decrease the errors caused in numerical process. The optimization method proposed can diminish the deviations occurred by material properties and numerical errors, simultaneously. As a results, it is shown that the final stress distributions for the HP shell model are sufficiently near to design stress distributions, and it can be concluded that this method can be used to obtain the optimized cutting pattern of membrane structures.

• 한국음향학회지
• /
• 제5권3호
• /
• pp.36-43
• /
• 1986

수치해석분야에서 도함수를 구하는 한 방ㅂ버으로서 최근에는 pattern matching 기법을 사용하 고 있다. 본 논문에서는 pattern matching 프로그램을 구성하여 주어진 함수의 도함수를 구할 수 있는 production system을 실현하였다. 이 프로그램을 수행시킨 결과 다항함수의 도함수를 구할 수 있었으며 그 식을 간략히 할 수 있음도 보였다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권6호
• /
• pp.655-667
• /
• 2017

The results of a numerical study on the performance of a propeller operating near a free surface are presented. The numerical simulations were performed for the various advance coefficients and the submergence depths of the model propeller. The effects of the model propeller size were investigated using two different model propeller sizes for all cases. The wave pattern of the free surface and the flow structure around the propeller as well as the hydrodynamic characteristics of the propeller were investigated through simulation results. The thrust and torque fluctuated and the trajectory of the tip vortex was distorted due to the interaction with the free surface. The wave pattern of the free surface was related to the tip vortex of the propeller. The decreases in thrust and torque at the small model propeller were greater than those of the large model propeller. The reduction rate of the thrust and torque increased with the advance coefficient.

• 한국분무공학회지
• /
• 제20권1호
• /
• pp.1-6
• /
• 2015

Visualization of the mixing pattern in a non-element mixer was carried out using laser induced fluorescence(LIF) to evaluate characteristics of mixer consisting of the main flow pipe and branch flow pipes. The branch flows were injected periodically with the period $T_{in}$ normal to the main flow, and rhodamine B was mixed into the most upstream branch flow to visualize mixing pattern in the main flow pipe by LIF. The length of boundary line L of the LIF image was measured. In this study, a numerical analysis was performed to identify the mixing process of the non-element mixer, and the results were compared with experimental results. Each result was almost the same. When the number of branch flows is increased, the mixing pattern became complicated and was supposed to become chaotic. The length of boundary line L increased exponentially with an increase in the number of branch flows.

• 터널과지하공간
• /
• 제16권5호
• /
• pp.377-386
• /
• 2006

본 연구에서는 기존의 시추공 시험 발파 결과를 이용한 분석뿐만 아니라, 3차원 수치 해석으로 터널 굴착 시 실제 발파와 동일한 조건을 적용한 발파진동영향 검토를 실시하고 주변 구조물에 미치는 진동 영향을 분석하여 발파패턴 설계를 수행하였다.

• 한국기계가공학회지
• /
• 제13권4호
• /
• pp.21-27
• /
• 2014

The injection molding process has several advantages enabling it to produce large quantities of molded plastic products using a repetitive process. In recent years, it has been necessary to develop an injection molding process with micro/nano-sized patterns for application to the semiconductor industry and to the bio/nano manufacturing industry. In this study, we apply gas pressure to the inside of a mold and consider the gas dissolution phenomenon for a resin filling into a micro pattern with a line structure. Using numerical analysis, we calculate the filling ratio with respect to time for various internal gas pressures and various aspect ratios of the micro-patterns.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.228-239
• /
• 1992

The purpose of the present research is to develop an efficient numerical method for the calculation of potential flow and predict the wave-making resistance for the application to ship design of tuna purse seiner. The paper deals with the numerical calculation of potential flow around the series 60 with forward velocity by the new slender ship theory. This new slender ship theory is based on the asymptotic expression of the Kelvin-source, distributed over the small matrix at each transverse section so as to satisfy the approximate hull boundary condition due to the assumption of slender body. Some numerical results for series 60, C sub(b) =0.6, hull are presented in this paper. The wave pattern and wave resistance are computed at two Froude numbers, 0.267 and 0.304. These results are better than those of Michell's thin ship theory in comparison with measured results. However, it costs much time to compute not only wave resistance but also wave pattern over some range of Froude numbers. More improvements are strongly desired in the numerical procedure.