• Journal of the Korea Fashion and Costume Design Association
• /
• v.8 no.3
• /
• pp.17-25
• /
• 2006

We performed the objective sensibility evaluation on knitted fabrics by the following procedures: setting acrylic fabrics with knitted fabrics as basis, knitted five kinds of blended spun yarns and four kinds of twisted filament yams made by different twisting methods(the amount and direction of twist) then, measuring mechanical properties in the use Kawabata Evaluation System, obtaining hand values and total hand values. The results are as follows: First, A(F)/W acrylic/wool spun knits obtain high scores in bending, compressing, shear properties, MMD, and thickness among five kinds of acrylic-blended knit fabrics. A(S)/W acrylic/wool blended knit represented prominent values at compressing properties and thickness and so wool-blended yams demonstrated superior characters comparing other blended yarns. To contrast, acrylic/rayon blended knits showed low scores in bending properties, shear properties and thickness, so that it affects to total hand values. On the one hand, among the four kinds of acrylic filament knitted fabrics, they do not exhibit any notable dynamic differences such as tensile properties of knitted fabrics by the twist number and direction of filament yarns, bending, shear, compressing properties, weight and thickness except surface properties. Second, fabrics showed the most high score at FUKURAMI (fullness and softness) among the hand values. A(S)/W acrylic/wool blended knits obtaining the lowest values at SAHRI (crispness) outrank at total hand values, so that it was the predominant knitted fabric in objective sensibility evaluation. In total hand values, five kinds of acrylic blended knits got a higher score than four kinds of acrylic filament knits, and the amount and direction of twist did not influence on total hand values among the four kinds of acrylic filaments.

• Textile Coloration and Finishing
• /
• v.22 no.2
• /
• pp.173-179
• /
• 2010

In this study, we determine the stretch and shrinkage properties of conjugated yarns. The shrinkage(%) and elasticity(%) were determined by applying twist conditions of 0, 350, 800, 1000, 1200, 1400, 1600, 2000 T/M (twisting per meter). It is found that the shrinkage(%) and elasticity(%) gradually decreased with increasing T/M. Especially the elasticity(%) dramatically decreased over 1400 T/M condition. In contrast, it is showed that the handle and drapery properties decreased below 1000 T/M, which indicates that the optimal T/M condition could be 1000~1400. The effect of shrinkage(%) and elasticity(%) with different steam setting temperatures (60, 70, 80 and $90^{\circ}C$) was also determined. The shrinkage(%) decreased with increasing setting temperature, while the elasticity not changed. In this context, the optimal steam setting temperature could be $80^{\circ}C$ because it is not easy to weave with the yarns which was set below $80^{\circ}C$. The elasticity(%) decreased with increasing the density of warp and weft. To produce soft handle, excellent drapery and good stretch fabrics, the warp density needs to be reached by 90% of the ideal warp density. In the case of NaOH treatments to the fabrics, the elasticity(%) increased with increasing weight reduction. Therefore, this study have demonstrated that the conjugated yarns with core yarn and the SDY CD(cation dyeable spindraw yarn) as an effect yarn would be appropriate to produce excellent mixture-yarn, which displays clean appearance, good handle and excellent elasticity, The optimized conditions are as follows; 1000~1200 twist per meter, $80^{\circ}C$ steam setting temperature, 90% of ideal warp density and relaxation condition treated with 5g/l NaOH concentration.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.28 no.11
• /
• pp.1516-1523
• /
• 2004

The purpose of this study were to analyze the effect of weft knit structural characteristics on the subjective texture and sensibility. For this, the material was knitted into 8 kinds of weft plain knit fabrics with four kinds of fiber components such as wool, acryl, rayon, and nylon, 3 steps of densities and 3 steps of twist numbers to ply two yarns. The data were analyzed by factor analysis, ANOVA and multidimensional scaling. From factor analysis, subjective textures were categorized as 'bulk/resilience', 'surface/density' and 'soft/drape', and subjective sensibilities were categorized as 'natural/comfortable', 'feminine/elegance' and 'stable/neat' Among the knit structural characteristics, the component of fibers and the density of fabrics were the important factors to give variations in texture and sensibility : In comparison with wool knit of medium density, the knit fabrics of other components and different densities each showed a unique texture and sensibility. But twist number to ply two yams had a few influence on subjective properties. As a result of MDS analysis, the texture and sensibility of plain weft knit fabrics was classified as 'thin-full', 'hard-soft', 'young-old' and 'warm-cool'.

• Journal of Korean Association for Spatial Structures
• /
• v.21 no.4
• /
• pp.23-30
• /
• 2021

In this paper, a twisted shape structure with an elevation form favorable to the resistance of vibration caused by wind loads is selected from among the forms of high-rise buildings. The analytical model is a square, triangular, and hexagonal plane with a plane rotation angle of one degree from 0 to 3 degrees per each story. As a result of the analysis, as the twist angle increased, story drift ratio is increased. Responses with different eccentricity rates were shown by analytical models. Therefore planar shapes designed symmetrically to the horizontal axis of X and Y are considered advantageous for eccentricity and torsion deformation. In the case of the bending moment of the column, the response was amplified in the column supporting the base floor, the roof floor, the floor in which the cross-section of the vertical member changes, and the floor having the same number of nodes as the base floor. Finally, the axial force response of the column is determined to be absolutely affected by the gravity load compared to the lateral load.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.1
• /
• pp.203-210
• /
• 2017

In this paper, we propose a electrical/mechanical method to effectively diagnose the local deterioration of a 10m long power shielded twist pair cable defined by the American Wire Gauge (AWG) 14 specification using electrical/mechanical methods. The rapid deterioration of the cable proceeded by using the heating furnace, which is based on the Arrhenius equations proceeds from 0 to 35 years with the deteriorated equivalent model. In this paper, we introduce a method to diagnose the characteristics of locally deteriorated cable by using $S_{21}$ phase and frequency change rate measured by vector network analyzer which is the electrical diagnostic method. The measured $S_{21}$ phase and rate of change of frequency show a constant correlation with the number of years of locally deteriorated cable, thus it can be useful for diagnosing deteriorated cables. The change of modulus due to deterioration was measured by a modulus measuring device, which is defined by the ratio of deformation from the force externally applied to the cable, and the rate of modulus change also shows a constant correlation with the number of years of locally deteriorated cable. Finally, By combining the advantages of electrical/mechanical diagnostic methods, we can efficiently diagnose the local deterioration in the power shielded cable.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.1
• /
• pp.62-70
• /
• 2001

Three-dimensional dynamic stall over an oscillating wing has been analyzed by using a compressible Navier-Stokes code. The code solved the thin-layer Navirer-Stokes equations with a second-order time accuracy for a semispan wing with 0.3048m chord, a NACA 0015 airfoil section, and zero twist Computations were made for a freestream Mach number of 0.29, a chord Reynolds number of 1.95$\times$10(sup)6 and a reduced frequency equal to 0.1. Numerical results were compared with experimental data which include the hysteresis of lift, drag and moment at various wing span. The comparison reveals the quantitative as well as qualitative nature of the three-dimensional dynamic stall.

• Asian Pacific Journal of Cancer Prevention
• /
• v.16 no.2
• /
• pp.531-535
• /
• 2015

Vasculogenic mimicry (VM) refers to the unique ability of highly aggressive tumor cells to mimic the pattern of embryonic vasculogenesis, which was associated with invasion and metastasis. The grape seed proanthocyanidins (GSPs) had attracted much attention as a potential bioactive anti-carcinogenic agent. However, GSPs regulation of VM and its possible mechanisms in a triple-negative breast cancer cells (TNBCs) remain not clear. Therefore, we examined the effect of GSPs on VM information in HCC1937 cell model. In this study, we identified the VM structure via the three-dimensional (3D) matrix in vitro. Cell viability was measured using the CCK8 assay. The effects of GSPs on human triple-negative breast cancer cells (TNBCs) HCC1937 in terms of related proteins of VM information were determined using western blot analysis. In vitro, the tubular networks were found in highly invasive HCC1937 cells but not in the non-invasive MCF-7 cells when plated on matrigel. The number of vascular channels was significantly reduced when cells were exposed in GSPs ($100{\mu}g$/ml) and GSPs ($200{\mu}g/mL$) groups (all p<0.001). Furthermore, we found that treatment with GSPs promoted transition of the mesenchymal state to the epithelial state in HCC1937 cells as well as reducing the expression of Twist1 protein, a master EMT regulator.GSPs has the ability to inhibit VM information by the suppression of Twist1 protein that could be related to the reversal of epithelial-to-mesenchymal (EMT) process. It is firstly concluded that GSPs may be an p otential anti-VM botanical agent for human TNBCs.

• Fashion & Textile Research Journal
• /
• v.25 no.5
• /
• pp.651-660
• /
• 2023

This study aimed to research the local production of conductive composite yarn, a source material used in textile-type electrodes and circuits. The physical properties of an internationally available conductive composite yarn were analyzed. To manufacture the conductive composite yarn, we selected one type of conductive yarn with Ag-coated polyamide of 150d 1 ply, along with two types of polyethylene terephthalate (PET) with circular and triangular cross-sections, both with 150d 1 ply. The conductive composite yarn samples were manufactured at 250, 500, 750, and 1000 turns per meter (TPM). For both conductive composite yarn samples manufactured from two types of PET filaments, the twist contraction rate of the sample with a triangular cross-section was stable. Among the samples, the tensile strength of the sample manufactured at 750 TPM was the highest at approximately 4.1gf/d; the overall linear resistance was approximately 5.0 Ω/cm, which is within the target range. It was confirmed that the triangular cross-section sample manufactured with 750 TPM had a similar linear resistance value to the advanced product despite the increase in the number of twists. In future studies, we plan tomanufacture samples by varying the twist conditions to derive the optimal conductive yarn suitable for smartwear and smart textile manufacturing conditions.

• Journal of Mechanical Science and Technology
• /
• v.18 no.3
• /
• pp.526-532
• /
• 2004

A motionless mixer consists of a straight pipe or transfer tube containing the mixing elements that are used to cut, fold, twist, and re-combine the mixing fluid. The number of elements and their shape required in any application depend on the complexity of the mixing process. The objectives of this study are to develop new motionless mixers and to perform the experimental investigation of pressure drop in order to evaluate the performance of the new ones. Glycerin is used as a mixing fluid. Pressure drop is measured using a hydraulic manometer and correlations of friction factor are proposed as a function of Re. The friction factors of Sulzer SMX mixer are in qualitative good agreement with the published data. On the average, the friction factors of SSC and YNU mixers are about 36% lower than and 6% higher than that of the Sulzer one.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.8
• /
• pp.1117-1127
• /
• 2002

This paper is on the luster property of fertile fabric materials which is one of the important factors related to the development of clothing materials leading to the value-added products. Using several image analysis techniques, the optical properties, especially luster related ones, of the commercially available fabrics were measured and analyzed. The fabric samples included 6 kinds of preliminary experimental fabrics along with 22 kinds of fabric which were commercially available. The images acquired at various observing angles are taken by 44 Points and these Pictures are analyzed into luster through the image analysis program. The preliminary experiment demonstrated the effects of weave types and the number of yarn twist on the luster of the fabrics through the use of the image analysis program.