• 한국분무공학회지
• /
• 제16권4호
• /
• pp.176-185
• /
• 2011

The empirical correlations for the prediction of penetration height of liquid jet in crossflow are reviewed and classified in this study. Around thirty different correlations had been proposed by many investigators. It has generally known that the penetration height of a liquid jet in a cross-flow is a function of the liquid to air momentum flux ratio and the normalized downstream distance from the injector. However, several researchers incorporated the Weber number, liquid-to-water or air viscosity ratio, pressure ratio or Reynolds number, temperature ratio in the empirical correlations. The existing correlations can be grouped as correlations in a power-law, logarithmic, and exponential forms, respectively. Correlations in a power-law form can be further classified as three groups such as basic form, Weber number form and other parameters form. It should be pointed out that correlations in a logarithmic form in terms of Weber number or any other parameters could not be found. Universal correlation has still not been established due to the significant discrepancies between various correlations suggested to date. Several of the studies reported the significant discrepancies of predicted values by the existing correlations. The possible reasons for discrepancies will be summarized as measurement technique, assumptions made in defining terms in the liquid to air momentum flux ratio, difficulties in defining the boundaries of the liquid jets, and nozzle/injector geometry. Evaluation of validity for the correlations proposed recently by several investigators is essentially required. Those include eight power-law forms, two logarithmic forms, and one exponential form.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.764-767
• /
• 2003

The characteristics of diesel spray have much effect on the engine performances such as power. fuel consumption rate and emissions. Therefore, the measurement of fuel spray characteristics is very important for the improvement of heat engine. The factors which control diesel spray characteristics are injection pressure, ambient temperature and density etc. Spray behaviors are visualized by using the high speed video camera and spray angle, spray penetration are measured. Experimental equations of spray penetration and spray angle were derived by using the experimental results. 1) Ambient temperature and density influence on the characteristics of diesel spray. 2) Experimental equation of spray penetration is expressed as follows 0＜t＜ $t_{b}$ ; $S_1$=11.628$\Delta$ $P^{0.485}$ $\rho$$_{a}$ $^{-0.478}$ $t^{1.337}$, $t_{b}$ ＜t; $S_2$=7.457$\Delta$ $P^{0.523}$ $\rho$$_{a}$ $^{-0.382}$ $t^{0.548}$ 3) Experimental equation of spray Angie is expressed as follows $T_{a}$ =293K; Tan($\theta$/2)=059($\rho$$_{a}$ / $\rho$$_{f}$ )$^{0.437}$, $T_{a}$ =473K; Tan($\theta$/2)=0588($\rho$$_{a}$ / $\rho$$_{f}$ )$^{0.404}$_{f}$ )$^{0.404}$

• 한국분무공학회지
• /
• 제19권4호
• /
• pp.155-166
• /
• 2014

This review will be concentrated on the spray characteristics of bioethanol and its derived fuels such as ethanol-diesel, ethanol-biodiesel in compression ignition (CI) engines. The difficulty in meeting the severe limitations on NOx and PM emissions in CI engines has brought about many methods for the application of ethanol because ethanol diffusion flames in engine produce virtually no soot. The most popular method for the application of ethanol as a fuel in CI engines is the blending of ethanol with diesel. The physical properties of ethanol and its derivatives related to spray characteristics such as viscosity, density and surface tension are discussed. Viscosity and density of e-diesel and e-biodiesel generally are decreased with increase in ethanol content and temperature. More than 22% and 30% of ethanol addition would not satisfied the requirement of viscosity and density in EN 590, respectively. Investigation of neat ethanol sprays in CI engines was conducted by very few researchers. The effect of ambient temperature on liquid phase penetration is a controversial topic due to the opposite result between two studies. More researches are required for the spray characteristics of neat ethanol in CI engines. The ethanol blended fuels in CI engines can be classified into ethanol-diesel blend (e-diesel) and ethanol-biodiesel (e-biodiesel) blend. Even though dodecanol and n-butanol are rarely used, the addition of biodiesel as blend stabilizer is the prevailing method because it has the advantage of increasing the biofuel concentration in diesel fuel. Spray penetration and SMD of e-diesel and e-biodiesel decrease with increase in ethanol concentration, and in ambient pressure. However, spray angle is increased with increase in the ethanol percentage in e-diesel. As the ambient pressure increases, liquid phase penetration was decreased, but spray angle was increased in e-diesel. The increase in ambient temperature showed the slight effect on liquid phase penetration, but spray angle was decreased. A numerical study of micro-explosion concluded that the optimum composition of e-diesel binary mixture for micro-explosion was approximately E50D50, while that of e-biodiesel binary mixture was E30B70 due to the lower volatility of biodiesel. Adding less volatile biodiesel into the ternary mixture of ethanol-biodiesel-diesel can remarkably enhance micro-explosion. Addition of ethanol up to 20% in e-biodiesel showed no effect on spray penetration. However, increase of nozzle orifice diameter results in increase of spray penetration. The more study on liquid phase penetration and SMD in e-diesel and e-biodiesel is required.

• 한국추진공학회지
• /
• 제8권1호
• /
• pp.44-53
• /
• 2004

본 논문에서는 슬릿형 분사노즐의 출구 종횡비에 따라 3차원 화학반응 유동장을 수치적 계산을 통하여 그 특성을 조사하고 연소／혼합 촉진 방법을 고찰하였다. 내부유입유동과 슬릿측면 와동들 둘 다 혼합관점에서 고려되어야 한다는 것을 보여 주었다. 연소효율은 종횡비1.0을 기준으로 작은 경우가 낮고 압력손실 역시 종횡비가 작은 경우가 적다. 모든 결과들은 유동방향으로 긴 슬릿이 연소와 압력손실에 대해 바람직함을 나타내고 있다.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.8-14
• /
• 2004

future exhaust emission limits for diesel-driven passenger cars will force the automotive company to significantly develop of the new technologies of diesel engine respectively of the drive assemblies. As we know, the contributions of soot and nitrogen oxide is the main problems in diesel engine. Recently, as a result, the pilot injection of common-rail fuel injection system recognizes an alternative function to solve an environmental problem. This study describes the effect of the nozzle structure and driven characteristic of injector on pilot injection fur a passenger car common-rail system. The pilot spray structure such as spray tip penetration, spray speed and spray angle were obtained by high speed images, which is measured by the Mie scattering method with optical system fur high-speed temporal photography. Also the CFD analysis was carried out for fuel behavior under high pressure in between needle and nozzle of injector for common-rail system to know the condition of initial injection at experiment test. It was found that solenoid-driven injector with 5-hole was faster than 6-hole injector in spray speed at same conditions and piezo-driven injector showed faster response than solenoid injector.

• 한국추진공학회지
• /
• 제12권1호
• /
• pp.16-22
• /
• 2008

액체제트의 액적분열 분포특성을 알아보기 위해 아음속 유동 내로 수직 분사된 이유체 분무를 실험적으로 연구하였다. 노즐은 L/d=3의 외부혼합형을 사용하였으며 공기와 액체의 비를 $0\;{\sim}\;59.4%$까지 변화시키면서 분사하였다. 분무형상을 이미지화 하여 분무의 궤적과 분열특성을 관찰하였다. PDPA를 사용하여 액체제트 분열의 단면분포 특성을 측정하였으며 SMD, 액적속도, 그리고 체적유속을 측정하였다 이유체 분무로부터 공급되는 공기의 유량이 증가할수록 액체 제트의 충돌점은 노즐 입구와 좀 더 가까워졌으며, 침투거리는 증가하였고, 기체 액체 비를 증가시킴에 따라 좀 더 무화된 액체제트의 분포를 얻을 수 있었다.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.75-81
• /
• 2009

A study was performed to investigate the characteristics of two-phase jet injected into subsonic cross-flow using the external mixed gas blast two-phase nozzle. The shadowgraph method was adopted for the cross-flow jet visualization and PDPA system was used to measure droplet size, velocity, and volume flux. The atomization of two-phase jet is initially determined according to gas to liquid mass flow-rate ratio and the Reynolds number of cross-flows. The highest penetration trajectories of two-phase jet injected into cross-flow are governed by the momentum ratio at subsonic cross-flow. As GLR of two-phase jet injected into cross-flow increases, the droplet size decreases and the distribution area of volume flux increases. The distribution of volume flux that influenced by the counter vortex pair at the downstream of cross-flow is symmetric in shape of horseshoe.

• 대한기계학회논문집A
• /
• 제36권10호
• /
• pp.1115-1130
• /
• 2012

최근 원자로 압력용기 상부헤드 관통노즐 J-groove 용접부 주변에서 균열로 인한 냉각수 누출사고가 발행하고 있다. 이러한 사고의 원인은 용접에 의한 인장잔류응력, 농축된 붕산수 및 응력부식에 민감한 재료로 인한 일차수응력부식균열(PWSCC : primary water stress corrosion cracking)인 것으로 판명되었다. PWSCC 평가는 원자로 건전성 평가의 주요 관심사로서 용접에 의해 발생되는 잔류응력을 정확하게 예측함으로써 가능하다. 본 연구에서는 유한요소해석을 이용하여 국내 원자로의 일반적인 J-groove 용접부의 해석절차를 소개하고, 용접해석 관련 변수의 민감도 해석을 통해 잔류응력 예측기법을 제시하고자 한다. 이를 위해 2 차원 및 3 차원 요한요소해석 방법을 바탕으로 변수 민감도 해석을 수행하였으며, 기존 연구결과와 비교를 통해 해석절차 및 방법의 유용성을 검정하였다.

• 한국가스학회지
• /
• 제24권1호
• /
• pp.49-55
• /
• 2020

산업용 혹은 발전용 가스터빈에 사용되는 이중 콘형 예혼합 연소기의 다단 연소 특성을 이해하기 위하여 실험적연구를 수행하였다. 이를 위하여 기존에 모두 경사면에 공급되는 연료를 콘부분으로 일부 할애하는 방식으로 다단연소 방식을 구성하였으며 콘에서 분사되는 연료공급은 축방향과 콘 경사면 방향으로 하였다. 다단연소 연소특성을 이해하기 위하여 콘에서의 연료 분사 방향과 연료 분배율 변화에 대한 NOx와 CO의 배출 농도 그리고 벽면 온도분포를 측정하였다. 그 결과 총 연료에 대한 콘으로의 분배율이 3%인 경우 콘에서의 연료 분사방향에 관계없이 노즐내의 예혼합 영역에서 연료가 공기와 균일하게 혼합됨으로서 연소영역의 고온점 감소에 의하여 NOx 배출 농도가 감소된다. 그러나 콘에서 축방향으로 분사되는 연료분배율이 8%로 증가하는 경우 노즐 내부 예혼합 영역으로의 화염 역화로 인하여 NOx의 배출농도가 오히려 증가하게 된다.

• 한국항공우주학회지
• /
• 제34권6호
• /
• pp.51-58
• /
• 2006

횡단 유동장내에서 일어나는 분무 현상에 대하여 분사각 변화에 대한 특성과 단일 노즐 형상에서 노즐의 크기와 길이에 대한 분무 특성을 연구하였다. 노즐은 단일 구멍으로 직경이 0.5 ㎜이고 노즐 대 노즐길이의 비(L/D)는 1.0에서 6.0이며 이미지는 고해상 줌 렌즈를 이용한 CCD 카메라를 통해 얻었으며, SMD와 액적의 속도는 PDPA와 상용 프로그램인 Image Express를 사용하였다. 액체 제트의 궤적은 웨버수와 모멘텀비, 노즐형상 변화(L/D)에 영향을 받아 액주가 후방으로 휘어지는 현상이 나타났다. 분사각이 낮을 때(${\theta}$ < $90^{\circ}$)에 노즐 형상보다는 웨버수 증가가 액체 제트의 궤적에 더 크게 영향을 미쳤으며, 분사각이 높을 때(${\theta}$ > $90^{\circ}$)에 노즐 형상 변화에 의한 분열점 변화가 액체 제트의 궤적에 더 크게 영향을 미쳤다.