• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.89-95
• /
• 2000

To obtain an exact flow loss in piping systems is very important in the face of efficiency anticipation and work control of plant. The object of this study is to get the flow loss through the experiment for sudden expansion and contraction part of circular pipe nozzle. The experiment in this study is performed after getting the flow loss factor for sudden expansion and contraction through preliminary experiments. It is confirmed that the results of this study agreed with the approximated equation of Ikeda and Matsuo. It is proved that flow loss factor ${\zeta}_3$for sudden expansion and contraction part of circular pipe is dependent on $L/D_1$in these experimental conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.68-75
• /
• 2017

Dual bell nozzle is a type of altitude compensation nozzle, which is a nozzle that minimize the losses of the specific impulse at the off-design point of a typical bell nozzle. In this paper, numerical computations are performed to understand the transition characteristics of dual bell nozzles with fixed expansion ratios. The major design variables are the length of extension and the angle of inflection. As the length of the extension increased, the transition altitude and transition duration increased and the reduction of the thrust coefficient decreased. As the angle of inflection increased, the transition altitude and transition duration decreased and the reduction of the thrust coefficient increased.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1311-1319
• /
• 1990

For the purpose of preventing the flow undulation in the cascade of steam turbine, the blades are made into a constant expansion rate in static pressure. And the flow in those cascades is transonic or supersonic in the range of 0.7-2.0 in Mach number. As a consequence, an oblique shock wave, known as inner or outer edge shock wave, arises in the flow of cascades. Especially when the steam in cascades is in a state of high wetness, nonequilibrium condensation and condensation shock wave occur, and they give rise to an interference with oblique shock wave. In the present study the case of expansion of moist air through a supersonic nozzle of constant expansion rate, which behaves similar to that of wet steam, was adopted. The effect of nonequilibrium condensation on the oblique shock wave generated by placing the wedge into the supersonic part of the nozzle was investigated. Furthermore, the relationship between nonequilibrium condensation zone and incident point of the oblique shock wave, oblique shock wave angle, the variations of angles of incident and reflected shock waves due to the variation of initial stagnation supersaturation and the relationship between the height of Mach stem and initial stagnation supersaturation are discussed.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.160-164
• /
• 1995

In order to develop a medium voltage class gas circuit breaker by our own technology, we designed and manufactured the model interrupters using the hybrid arc extinguishing principle which adopts the thermal expansion principle in the large current region and the arc rotation principle by permanent magnet in the small current region. As the results of the first year research out of three years' research period, the main design parameters such as the volume of thermal expansion chamber, the distance between fixed contact and nozzle, the length of nozzle throat, the nozzle expansion angle and the magnitude of permanent magnet etc. have been determined. 4 types of model interrupters have been designed and manufactured considering the main design parameters. The 25kA short-circuit test and capacitive current breaking test have been performed for the model interrupters and the test results analyzed to improve the model interupters.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.644-648
• /
• 2004

In the present study were examined numerically and experimentally the off-design performance characteristics on an axisymmetric plug nozzle with variable throat area. In this nozzle concept, its throat area can be changed by translating the plug into the axial direction. First, a mixed-expansion plug nozzle, in which two expansion parts are arranged both inside and outside, was designed by means of the method of characteristics. Second, the CFD analysis was verified by the cold-flow wind tunnel test. Third, its performance characteristics were evaluated over a wide range of pressure ratio from half to double throat area through the design point, using the CFD code verified by the wind tunnel tests. It was made clear from the study that not so critical thrust efficiency losses were found and the maximum thrust efficiency loss was at most approximately 5 % under off-design conditions without external flow. This result shows that a plug nozzle can give the altitude compensation even under off-design geometry operations. However, shock waves were observed in the inner expansion part under the doubled throat area operation and thus some thermal problems may be caused on the plug surface. Furthermore, collapse of cell structure on the plug surface was observed with external flow (around Mach number 2.0) as it became lower pressure ratio below the design point and the fact may result in big efficiency loss regardless of geometrical configuration.

• Aerospace Engineering and Technology
• /
• v.1 no.1
• /
• pp.153-162
• /
• 2002

This paper predicted the engineering constants of spatially reinforced carbon/ carbon composites and analyzed the mechanical behaviour of the kick motor nozzle. Those equivalent engineering constants are used to analyze the mechanical behaviour of the kick motor nozzle. Because the distribution of equivalent engineering constants is varying as change its structure, we made a program to predict engineering constants of spatially reinforced composites. The kick motor nozzle consists of graphite or spatially reinforced carbon/ carbon composites for the nozzle throat, carbon/ phenol for the nozzle entrance and the expansion part, and steel for the outer surface of the expansion part. The 4-D carbon/ carbon composite shows the smallest deformed shape of the nozzle throat, which has a favorable effect on the rocket thrust, and the most uniform deformation of all nozzle throat materials. In addition to analysis, ground firing tests of 4D C/ C nozzle throat and graphite nozzle throat were performed.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.2
• /
• pp.697-709
• /
• 1996

Supersonic axisymmetric jets issuing from various kinds of nozzles with a throat diameter of a few millimeters were experimentally investigated. The exit Mach number and Reynolds number based on the throat diameter of nozzle were in the range of 1.0 ~ 5.9 and 8.4$\times$ $10^4$ ~ 2.9$\times$$10^6$, respectively. The nozzle pressure ratio was varied from 5 to 85. Present paper aims to offer fundamental information of the supersonic free-jets, with an emphasis to give data with which the shape of the free-jets can be depicted under a specified condition. Experimental data are summarized to enable an estimation of the shape of the supersonic free-jets. The result shows that the shape of free-jets is dependent on only the nozzle pressure ratio.

• International Journal of Aeronautical and Space Sciences
• /
• v.6 no.1
• /
• pp.1-7
• /
• 2005

The inlet boundary condition of computations about the supersonic turbine flow is commonly applied as far-field inlet boundary condition with specified velocity. However, the inflow condition of supersonic turbine is sometimes affected by the shocks or expansion waves propagated from leading edges of blade. These shocks and expansion waves alter the inlet boundary condition. In this case, the inlet boundary condition can not be specified Therefore, in this paper, numerical analyses for three different inlet conditions - fa-field inlet boundary condition, inlet boundary condition with a linear nozzle and inlet boundary condition with a converging-diverging nozzle - have been performed and compared with experimental results to solve the problem. It is found that the inlet condition with a linear nozzle or a converging-diverging nozzle can prevent changing of inlet boundary condition, and thus predict more accurately the supersonic flow within turbine cascade than a far-field inlet boundary condition does.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.379-382
• /
• 2017

Flow characteristics of dual bell nozzle with pintle were investigated. Thrust and thrust coefficient were compared with the pintle-bell nozzle of the same condition, and difference according to the pintle stroke was investigated. At stroke 0 mm, the thrust of the dual bell nozzle was about 13.18% higher than the bell nozzle, and when the pintle was backward, it was similar to the bell nozzle. The change in expansion ratio with stroke was considered to be more advantageous for a dual bell nozzle that performs altitude compensation through separation and transition.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.2
• /
• pp.145-147
• /
• 1998