• 한국터널지하공간학회 논문집
• /
• 제13권1호
• /
• pp.1-8
• /
• 2011

장대 도로터널 및 위험도가 높은 도로터널에 설치되고 있는 물분무소화설비는 성능과 관계된 단위면적당 방수밀도에 대한 검증과정이 없이 사용되어 왔다. 본 연구는 도로터널에 물분무소화설비에 노즐을 설치하여 기준압력에서 방수시험을 실시하여 기준을 만족하는지 여부를 확인하였다. 결론적으로 모든 노즐이 기준을 만족하지 못하였다. 이런 결과는 도로터널용 물분무노즐을 검증하는 시험기준이 없고, 실제 시험을 통한 검증 과정이 존재하지 않았기 때문이라고 판단된다. 따라서 물분무노즐의 성능을 시험할 수 있는 기준의 마련과 설치된 시설을 검증하는 제도적인 보완이 필요하다.

• International Journal of Aeronautical and Space Sciences
• /
• 제4권2호
• /
• pp.51-60
• /
• 2003

An experimental research program is being undertaken to develop a regeneratively-cooled experimental thrust chamber of liquid rocket engine using liquefied natural gas and liquid oxygen as propellants. Prior to firing test using a regenerative cooling with liquefied natural gas in this program, several firing tests were conducted with water as a coolant. Experimental thrust chambers with a thrust of about 10tf were developed and their firing test facility was built up. Injector used in the thrust chamber was of shear-coaxial type appropriate for propellants of gas and liquid phase and cooling channels are of milled rectangular configuration. Periodical variation of the soot deposition and discoloration was observed through an eyes' inspection on the inner wall of a combustion chamber and a nozzle after each firing test, and an intuitive concept of the periodical variation of mixture ratio near the inner wall of a combustion chamber and a nozzle at once was brought about and analyzed quantitatively. Thermal heat flux to the coolant was calculated and modified with the periodical variation model of mixture ratio, and the increment of coolant temperature at cooling channels was compared with measured one.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2004년도 제29회 KOSCI SYMPOSIUM 논문집
• /
• pp.79-84
• /
• 2004

For the non-premixed interacting jet flames, it has been reported that if eight small nozzles are arranged along the circle of 40 $^{\sim}$ 72 times the diameter of single jet, the flames are not extinguished over 2oom/s. In this research, experiments were extended to the partially premixed cases to reduce both flame temperature and NOx emission. Nine nozzles were used- eight was evenly located along the perimeter of the imaginary circle and one at the geometric centre. The space between nozzles, S, the equivalence ratio, ${\Phi}$, the exit velocity and the role of the jet from the centre nozzle were considered. Normally, flame was lifted and flame base was located inside the imaginary circle made by the nozzle. As nozzles went away from each other, blowout velocity increased and then decreased. The maximum blowout velocity diminished with the addition of air to the fuel stream. When the fuel and/or oxidizer were not fed through the centre nozzle, the maximum blowout velocity obtained by varying Sand ${\Phi}$ was around 160m/s. Optimum nozzle separation distance at which peak blowout velocity obtained also decreased with ${\Phi}$ decrease. Flame base became leaner as approaching to the blowout. It seemed that lots of air was supplied to the flame stabilizing region by the entrainment and partially premixing. To approve this idea and to enhance the blowout velocity, fuel was supplied to the centre region. With the small amount of fuel through the centre nozzle, partially premixed flame could be sustained till sonic velocities. It seemed that the stabilizing mechanism in partially premixed interacting flame was different from that of non-premixed case because one was stabilized by the fuel supply through the centre nozzle but the other destabilized.

• 대한기계학회논문집B
• /
• 제29권1호
• /
• pp.71-79
• /
• 2005

For the non-premixed interacting jet flames, it has been reported that if eight small nozzles are arranged along the circle of $40{\sim}72$ times the diameter of single jet, the flames are not extinguished even in 200m/s. In this research, experiments were extended to the partially premixed cases to reduce both flame temperature and NOx emission. Nine nozzles were used- eight was evenly located along the perimeter of the imaginary circle and one at the geometric centre. The space between nozzles, S, the equivalence ratio, ${\phi}$, the exit velocity and the role of the jet from the centre nozzle were considered. Normally, flame was lifted and flame base was located inside the imaginary circle made by the nozzle. As nozzles went away from each other, blowout velocity increased and then decreased. The maximum blowout velocity diminished with the addition of air to the fuel stream. When the fuel and/or oxidizer were not fed through the centre nozzle, the maximum blowout velocity obtained by varying S and ${\phi}$ was around 160m/s. Optimum nozzle separation distance at which peak blowout velocity obtained also decreased with ${\phi}$ decrease. Flame base became leaner as approaching to the blowout. It seemed that lots of air was supplied to the flame stabilizing region by the entrainment and partially premixing. To approve this idea and to enhance the blowout velocity, fuel was supplied to the centre region. With the small amount of fuel through the centre nozzle, partially premixed flame could be sustained till sonic velocities. It seemed that the stabilizing mechanism in partially premixed interacting flame was different from that of non-premixed case because one was stabilized by the fuel supply through the centre nozzle but the other destabilized.

• 한국추진공학회지
• /
• 제23권5호
• /
• pp.101-106
• /
• 2019

액체산소/케로신 가스발생기 사이클 엔진의 터빈 노즐목 수트(soot) 침착 특성을 파악하기 위한 변수를 정의하고 한국형발사체 1단 엔진 시험결과에 적용하였다. 터빈 가스의 물성치를 이용한 노즐목의 분출 계수 정의를 하는 방법이 있고 터빈 노즐목 전단과 터빈 배기 노즐목 전단의 압력비와 온도비를 이용하여 분출계수를 정의할 수 있다. 한국형발사체 1단 엔진 시험 결과를 분석한 결과 터빈 노즐목의 분출계수(discharge coefficient)는 시간에 따라 감소하며 동일 엔진에 대한 누적 연소시간에 대해서도 감소하는 경향을 보인다. 누적 시험 초기에는 터빈 노즐목 감소가 그 다음 시험과 연계되지만 일정 시간 이후에는 일정 범위에서 등락을 거듭하는 듯한 특성을 보인다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.472-484
• /
• 2002

To analyze the characteristics of air flow and $CO_2$ extinguishant transfer when extinguishant is injected into a closed space similar to marine engine room, a numerical simulation on a space was performed. Flow fields and $CO_2$ concentration fields are calculated according with the variation of the location & injection angle of nozzles. The results of simulation showed that the pattern of recirculation flow was affected greatly with the location & injection angle of nozzles and such a recirculation flow accelerated mass transfer of $CO_2$ and greatly affected the diffusion process of $CO_2$ extinguishant. It is considered that this result of this study can be useful to designing the arrangement of nozzles for the $CO_2$ fire fighting equipments in a marine engine room.

• International Journal of Aeronautical and Space Sciences
• /
• 제15권1호
• /
• pp.91-96
• /
• 2014

The aim of this work is to determine supersonic nozzle profiles that are used in propulsion, for launchers or embarked with satellites. This design has the role of firstly, providing important propulsion, i.e. with uniform and parallel flow at exit; and secondly, to find short length profiles, without modification of the flow in the nozzle. The first elaborate program is used to determine the profile of the divergent, by using the characteristics method for an axisymmetric flow. The second program is conceived by using the finite volume method, to determine and test the profile found connected to a convergent.

• International Journal of Aeronautical and Space Sciences
• /
• 제3권2호
• /
• pp.67-75
• /
• 2002

In the course of missile system design, jet plume impingement is encountered in designing airframe as well as launchers, requiring careful investigation of its effect on the system. In the present paper, recent works on such topic are presented to demonstrate usefulness of CFD results in helping design the hardware. The jet impinging flow structure exhibits such complex nature as shock shell, plate shock and Mach disk depending on the flow parameters. The main parameters are the ratio of the jet pressure to the ambient pressure and the distance between the nozzle and the wall. In the current application, the nozzle contour and the pressure ratio are held fixed, but the jet impinging distance is varied to illuminate the characteristics of the jet plume with the distance. The same methodology is then applied to a complex vertical launcher system (VLS), capturing its flow structure and major design parameter. These applications involving jets are thus hoped to demonstrate the usefulness and value of CFD in designing a complex structure in the real engineering environment.

• International Journal of Aeronautical and Space Sciences
• /
• 제5권2호
• /
• pp.9-17
• /
• 2004

In this paper, a small supersonic wind tunnel was designed and built to studythe flow characteristics of a supersonic impulse turbine cascade by experiment. Theflow was visualized by means of a single pass Schlieren system. The supersoniccascade with 3-dimensional supersonic nozzle was tested over a wide range ofpressure ratio. Highly complicated flow patterns including shocks, nozzle-cascadeinteraction and shock boundary layer interactions were observed.

• 한국터널지하공간학회 논문집
• /
• 제23권6호
• /
• pp.589-604
• /
• 2021

워터젯 암반 굴착공법은 물과 연마재만을 사용하는 친환경 및 비접촉식 굴착방법으로 다양한 장점을 가지고 있다. 최근에는 기존 천공 공법의 문제점을 보완하고 분진 방지, 소음 저하 등의 이유로 워터젯 공법의 활용이 증가하고 있다. 워터젯 굴착효율을 증대시키기 위해서는 복수의 노즐을 운용하는 것이 유리하다. 복수의 노즐을 사용할 경우, 노즐 운용방법에 따른 굴착성능과 형상을 분석하는 것이 필수적이다. 본 연구에서는 노즐각, 노즐 간 수평거리, 이격거리를 노즐 운용변수로 정의하고 굴착성능과 형상을 분석하였다. 실험결과, 노즐각과 이격거리가 증가할 때 굴착깊이는 감소하였고 유효 굴착깊이는 증가하는 경향을 보였다. 또한, 실험결과를 바탕으로 노즐 삽입에 필요한 굴착형상 기준을 제안하고 기준에 따른 최적 노즐 운용변수를 도출하였다. 본 연구결과는 향후 암반 천공용 다중 워터젯 노즐 개발 시 유용한 기초연구로 활용될 것으로 기대된다.