• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.891_892
• /
• 2009

This paper presents the rotor study on the deal with the shape design with a flux barrier to minimize the cogging torque of Interior Permanent Magnet Synchronous Motor(IPMSM). In order to consider the notch effect, the torque characteristics according to the shape of notch is performed and analyzed. From the this results, we found that an optimal location and radius of the notch effectively suppresses the torque pulsation of the IPM drive. The rotor shape design also shows improvement in the average torque

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.86-88
• /
• 2007

By reason of variation magnetic field, cogging torque is generated. Cogging torque of Spoke type motor is bigger than other type permanent magnet motor. So, this paper presents a design notch on stator and variation rotor shape to reduce cogging torque of Spoke Type motor. Through Fourier formulation of magnetic field on air gap, we found position of notch. The validity of the proposed design is confirmed with FEM analysis method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.848-851
• /
• 2005

This paper proposes a design of IIR notch filter with modified pole placements. The pole angle is derived from quadratic programming to find the appropriate pole position on the unit circle in z-plane in order to achieve the symmetry of the amplitude response. The simulation results are shown when compared with the conventional design technique. Moreover, it uses the TMS320C31 DSP chip for hardware implementation. Finally, the hardware implementation can be applied to removal of ECG baseline wander and elimination of AC power line interference in ECG signal.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.192-197
• /
• 1994

High-Tc superconducting magnet properties were dependent upon design conditions such as its radius, length, critical current and notch size. In order to study, design and the simulation for small size magnet were implemented. We know that intensity of magnetic fields controled by critical current and factor ${\alpha}$( R$_2$/R$_1$) and uniformity controled by notch size. The optimal condition of intensity and uniformity magnetic field in this experiments are R$_1$=3[cm], R$_2$=12[cm], Z=10[cm], ${\alpha}$=4, notch=6[cm], critical current=12[A].

• Polymer(Korea)
• /
• v.36 no.1
• /
• pp.59-64
• /
• 2012

The impact strength of material is considered the most important design factor for small and light products. Impact strength is a unique material property, thus the impact strength should not depend upon the geometry of specimen. However it varies according to specimen thickness, notching method, and notch shape. In this study, the variations of impact strength have been investigated according to thickness, notch shape, and notching method of specimen. Engineering plastics such as PC, ABS and POM have been used in this study. Experimental results showed impact strength increased as thickness decreasesd. PC showed the highest increment of impact strength when the thickness was thin. Fractured section of PC showed brittle fracture behavior when the specimen was thick. However it showed ductile fracture behavior when it was thin. The impact strength of in-mold notched specimen showed higher than that of milling notched specimen. PC showed the highest notch sensitivity among the materials used in this experiment.

• Journal of Korea Society of Industrial Information Systems
• /
• v.18 no.1
• /
• pp.11-17
• /
• 2013

A design method to achieve multiple band-rejection characteristics in a wideband circular slot antenna is presented. First, a wideband circular slot antenna fed by a coplanar waveguide is designed to operate in the frequency range between 2.3 and 11GHz, which covers WLAN, WiBro, WiMAX, and UWB frequency bands. Next, resonant frequency variations of rejection bands are examined with respect to different slot locations and lengths when slots are inserted on the ground conductor and the circular patch of the antenna. When arc-shaped slots are placed close to the circular transition from a feeding part, multiple notch bands are obtained. In this case, a half of the guided wavelength of the first notch band corresponds to the slot length and other notch bands are integer-multiple of the first band. Single notch band can be obtained when the slot is located off the transition part. Based on this study, a wideband circular slot antenna with five band-rejection frequency bands at 2.45, 3.5, 4.9, 7.35, and 9.8GHz is designed and fabricated. The first arc-shaped slots are located in the ground conductor close to the circular transition from a feeding part to generate notch bands at 2.45, 4.9, 7.35, and 9.8GHz, while the second slot for 3.73 GHz is placed on top side in the circular patch. The proposed design method is validated by good agreement between the simulated and measured results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1215-1216
• /
• 2013

• Tribology and Lubricants
• /
• v.13 no.1
• /
• pp.14-20
• /
• 1997

This paper reports on theoretical study of the pressure overshoot in the delivery ports and pressure rising within balanced type vane pump. Pressure overshoot occur due to the accelerated fluid through the notch, so, result in pressure ripple, flow ripple, and noise. For calculating the pressure rising and fluctuations of pressure, we have modeled mathematically used continuity equation based on compressibility and momentum equation considered fluid inertia in the notch, and analyzed simultaneously. As a results of analysis, we have found oscillation of pressure and compression chamber pressure depend on the rotational speeds, notches. Using the model, notches have been shown to be important design factor in relaxing the rapid pressure rising and reducing the amplitudes of pressure overshoot.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.11
• /
• pp.1535-1540
• /
• 2013

In this paper, the Radial Magnetic Force(RMF) and cogging torque which cause vibration and noise in IPM type BLDC motor were analyzed. The cogging torque and RMF cause electromagnetic vibration. So, a notch was installed for the equilibrium of RMF and cogging torque reduction. The notch was analyzed by using a Fourier Series for the energy distribution of the air-gap. The equilibrium of RMF and the reduction of cogging torque were performed by a Design Of Experiment(DOE) with the notch. Also, operating characteristics and efficiency were analyzed and compared.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.533-539
• /
• 1997

Pressure ripple of hydraulic vane pump results form flow ripple due to pump geometry and reverse flow through the discharge port due to compressibility of fluid and result in vibration and noise of connected hydraulic elements. In a ba;anced type vane pump, cam ring curve is important factor to influence the flow ripple. Therefore, to reduce the now ripple, it has been required that optimal selection of seal region by proper design of cam ring and each port position, and notches for preventing the excessive reverse flow. This paper has been performed analytical study of compression characteristics with major design parameter in side plate and cam ring, and examined into the role of notch and radius reduction ratio.