• Journal of Industrial Technology
• /
• v.12
• /
• pp.25-36
• /
• 1992

In this paper, we simulate and calculate the stress and output voltage of the beam structure load cells by using FEM as varing physical structure parameters and loading positions. It is proved that stress enhance as the increase of the notch pitch and radius of the load cell, but decrease as the increase of the notch thickness and beam width. The results are good matched for basic formulas of the single fixed beam, and are verified our simulation is correct. Also, it is found that the stress characteristics of the load cell is varied according to loading positions with structure parameters, and caculated output voltage of the load cell approximate to those of the real manufactured ones. As a result, this study will offer efficient design and analysis technique for making special and variety capacity of load cells.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.862-863
• /
• 2008

This paper presents the improvement of dynamic characteristics in Interior Permanent Magnet (IPM) type BLDC motor with notch. The notch is applied on the surface of the rotor to reduce the cogging torque and to improve dynamic characteristics. The current, inductance and torque of initial model and optimal model are analyzed by FEA. The validity of improved dynamic characteristics is confirmed.

• Proceedings of the KIEE Conference
• /
• 2008.10c
• /
• pp.44-46
• /
• 2008

This paper presented the notch effect of interior permanent magnet motor(IPM) with compound variable number of pole and slot. The selection of proper pole and slot which makes characteristic and efficiency of motor is very important on motor design. The motor which has 6pole and 9slot is at base. This paper is choose the 4pole 6slot motor which has 2:3 ratio then analyzed the characteristic.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1577-1581
• /
• 2014

This paper presents a method to minimize torque ripple of a V-type IPMSM using the PSO (Particle Swarm Optimization) method with FEM. The proposed algorithm includes one objective function and three design variables for a notch on the surface of a rotor. The simulation model of the V-type IPMSM has 3-phases, 8-poles and 48 slots with 2 notches on the one-pole rotor surface. The arc-angle, length and width of the notch are optimized to minimize the torque ripple of the motor. The cogging torque of the model is reduced by 55.6% and the torque ripple is decreased by 15.5 %. Also, the efficiency of the motor is increased by 15.5 %.

• Journal of Power Electronics
• /
• v.12 no.4
• /
• pp.654-663
• /
• 2012

In this paper, a digital control strategy based on equivalent fundamental and odd harmonic resonators is proposed for single-phase DVRs. By using a delay block, which can be equivalent to a bank of resonators, it rejects the fundamental and odd harmonic disturbances effectively. The structure of the single closed-loop control system consists of a delay block, a proportional gain and a set of zero phase notch filters. The principle of the controller design is discussed in detail to ensure the stability of the system. Both the supply voltage and the load current feedforwards are used to improve the response speed and the ability to eliminate disturbances. The proposed controller is simple in terms of its structure and implementation. It has good performances in harmonic compensation and dynamic response. Experimental results from a 2kW DVR prototype confirm the validity of the design procedure and the effectiveness of the control strategy.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.2
• /
• pp.1-7
• /
• 2015

In this paper, a new capacitive pressure sensor has been proposed for a displacement measurement. The new sensor is mainly composed of a gap of $5{\mu}m$ and a notch of $1{\mu}m$. And the sensor has the performance as the high sensitivity and capacitance compared with a commercial capacitive sensor. Therefore, the advantages of the new capacitive pressure sensor are good sensitivity in normal range, mechanically robust and large overload protection. The analytical model is induced for confirming the performance of the proposed sensor. In addition, FEM (finite elements method) simulation has been performed to verify the analytical model. Firstly, the displacement characteristics of diaphragm membrane were simulated by the analytical model and FEM in the case of different structure and materials. At last, through this analysis, these simulation results can be predicted the change of the performance when the device parameters are varied. And it is used as a design tool to achieve at a set of performance we desired.

• Progress in Superconductivity
• /
• v.13 no.3
• /
• pp.195-202
• /
• 2012

In this paper, we designed Active Magnetic Bearing (AMB) for large scale Superconductor Flywheel Energy Storage System (SFESS) and PD controller for AMB. And we experimentally evaluated SFESS including hybrid type AMB. The radial AMB was designed to provide force slew rate that was sufficient for the unbalance disturbances at the maximum operating speed. The thrust AMB is a hybrid type where a permanent magnet carries the weight of the flywheel and an electromagnetic actuator generates the dynamic control force. We evaluated the design performance of the manufactured AMB through comparison of FEM analysis and the results of experimental force measurement. In order to obtain gains of PD controller and design a notch filter, the system identification was performed through measuring frequency response including dynamics for the AMBs, a power amp and a sensor using a sine swept test method after levitating the flywheel. Through measuring the current input of the AMBs and the orbit of a flywheel according to rotational speed, we verified excellent control performance of the AMBs with small amount current for the large scale SFESS.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.271-272
• /
• 2006

This paper presented a new experimental gain tuning technique for a Multi-Axis Servo System. First, the investigation for proportional gain of velocity control loop by using a Dynamic Signal Analyzer (DSA) was performed. Using the FUNCTION characteristic of DSA based on the Bode plot, the Bode plot of open loop transfer function was obtained. In turn, the integral gain of a servo controller can be found out by using the Integration time constant extracted from the Bode plot of open loop transfer function. In the meanwhile, the positional gain of the servo controller has been obtained by using the Bode plot of the closed loop transfer function. We have also proposed the technique to find out an optimal parameter of a notch filter, which has a great influence on vibration reduction, by using the damping factor extracted from the Bode plot of closed loop transfer function.

• Steel and Composite Structures
• /
• v.1 no.4
• /
• pp.411-426
• /
• 2001

This paper treats the failure analysis of prestressing steel wires with different kinds of localised damage in the form of a surface defect (crack or notch) or as a mechanical action (transverse loads). From the microscopical point of view, the micromechanisms of fracture are shear dimples (associated with localised plasticity) in the case of the transverse loads and cleavage-like (related to a weakest-link fracture micromechanism) in the case of cracked wires. In the notched geometries the microscopic modes of fracture range from the ductile micro-void coalescence to the brittle cleavage, depending on the stress triaxiality in the vicinity of the notch tip. From the macroscopical point of view, fracture criteria are proposed as design criteria in damage tolerance analyses. The transverse load situation is solved by using an upper bound theorem of limit analysis in plasticity. The case of the cracked wire may be treated using fracture criteria in the framework of linear elastic fracture mechanics on the basis of a previous finite element computation of the stress intensity factor in the cracked cylinder. Notched geometries require the use of elastic-plastic fracture mechanics and numerical analysis of the stress-strain state at the failure situation. A fracture criterion is formulated on the basis of the critical value of the effective or equivalent stress in the Von Mises sense.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.776-779
• /
• 1992

This paper describes the auto-depth control system with depth control tank for low speed submersible vehicle that can be used for both near surface and deeply submerged keeping operations. The PDA control algorithm is used to design controller and adaptive notch filter is designed to eliminate the dominant frequency of seaway. The computer simulations demonstrate the excellent depth keeping performance of the controller under seaway effects.